Kawasaki Mule Lift Kit Installation Manual

0

Filed Under (Kawasaki) by admin on 04-05-2012

download
Front Lift Installation 1. Ensuring that the parking brake is set, place jack under center of the Mule front end and lift until front wheels clear the ground. Be careful to support Mule properly so that it is secure, but so that the A-arms and struts can droop to full extension. 2. Remove front wheels. 3. If applicable, remove the heater to allow access to the strut mount behind the heater coil. Heater 4. Starting with the left side (driver side), remove the cotter pin and castle nut that secures the strut to the strut mount. Castle Nut & Pen 5. Push bolt through the bolthole, taking care not to damage the brake line that is attached to the bolt. If you are having difficulty removing the bolt, you may have to remove the brake lines that are attached to the front brakes. In this case refer to owners manual for removing brake lines. Screwdriver NOTE: Keep in mind that if you remove the brake lines you must bleed your brakes according to operator’s manual. 6. Once the bottom of the strut has been loosened, then unbolt the top of the strut. The nuts securing the top strut can be located in the dash of the Mule on the left and right sides. In most cases these nuts are easily accessible, but you may have to remove the glove box or heater coils, depending on the model and options purchased with the Mule.

Incoming search terms:

Honda ATV 650 Lift Kit REMOVAL AND Installation

0

Filed Under (Honda) by admin on 14-01-2012

download
Place jack under center on the ATV front end and lift until front wheels clear the ground. Be careful to support ATV properly so that it is secure, but so that the A-arms and shocks can droop to full extension. 2. Remove front wheels and shocks. 3. Using a shock spring compressor, compress the spring on the shock and remove the spring retaining ring.
CAUTION: The spring is installed under tension. Failure to use a shock spring compressor could cause loss of control of the spring, which could unload rapidly causing bodily injury. If you do not have a shock spring compressor you should acquire one or take it to a dealer or professional mechanic for installation of the stiffeners. 4. Remove the spring. 5. Insert the smaller front spring stiffener onto the shock with the lip of the spring stop, on the shock, mating into the recessed portion of the spring stiffener. 6. Slide the spring back onto the shock and it should rest on the lip of the spring stiffener.
7. Reattach the spring retaining ring. 8. Repeat steps for the opposite side. Once springs are complete reattach the top of the shock to the top shock mount on the ATV and the spring stiffener will be closest to the A-arm. 9. Take two of the ā€œLā€ brackets and connect them to the bottom of the shock, the part that connects to the A-arms. 10. There is a top and bottom to the ā€œLā€ bracket. See the diagram

TOYOTA Steering Intermediate Shaft Knocking Noise

0

Filed Under (Toyota Manuals) by admin on 13-10-2011

download
Some 2009-2010 Corolla and Matrix vehicles ma yexhibitaclunk, pop, or knocking noise when turning the steering wheel to the left or right. Anew intermediate shaft has been developed to address this condition. Use the following repair procedure to remove and replace the steering intermediate shaft. Install a steering wheel lock to ensure the wheels are straight and the steering wheel is centered before removing the steering intermediate shaft. Make sure the steering wheel and front wheels remain stationary. Once the intermediate shaft is removed, do NOT allow the steering wheel to spin freely. 2. Remove the column hole silencer sheet

Toyota Camry TRANSMISSION REMOVAL & INSTALLATION – M/ T

0

Filed Under (Toyota Manuals) by admin on 21-06-2011

Download
1) Disconnect negative battery cable. Remove air cleaner case
with air intake hose. Remove cruise control actuator. Remove clutch
release cylinder with hose attached and secure aside.
2) Remove starter. Disconnect necessary ground straps,
electrical connections and control cables from transaxle. Remove upper
transaxle mounting bolts from cylinder block.
3) Raise and support vehicle. Remove front wheels. Remove
lower engine covers. Drain transaxle fluid. Remove axle shafts from
transaxle. See appropriate AXLE SHAFTS article in AXLE SHAFTS &
TRANSFER CASES section. Remove stabilizer bar mount and bushing from
crossmember

Incoming search terms:

1500cc Honda Goldwing Installation Manual

0

Filed Under (Honda) by admin on 02-12-2010

download
Review entire installation manual Loosen saddle bags and remove rear fender cover Modify rear fender cover Install receiver hitch and double check all bolts Remount rear fender and tighten saddle bags Assemble InstaTrike hitch cart Attach InstaTrike to motorcycle via receiver hitch Attach leanstop brace bolts to receiver hitch Align InstaTrike wheels Double check all bolts for tightness Test ride InstaTrike slowly in an open area to familiarize yourself with handling characteristics Receiver Hitch Installation NOTICE: Install all bolts and brackets loosely until all bolts and brackets are in place 1) Place motorcycle on center stand. NOTE: Some Goldwings are not level when on center stand. Shim underneath center stand to level motorcycle. 2) Remove side covers 3) Loosen saddle bags and remove rear fender cover. 4) Modify rear fender cover. See diagram 5) Remove muffler bolts. Replace with enclosed muffler bolts. (hex bolt head toward inside with washers on bolt head side) This allows clearance between the hitch and muffler bolt. 6) Replace existing motorcycle rear crashbar bolts with those provided (2 each side). Ensure new crashbar bolts are securely tightened before attaching brackets A and B. 7) With brackets A (left) and B (right) attached to bottom of forward arms of hitch, slide hitch under bike and loosely attach A and B to bottom of rear crash bar with provided U-bolts. Use caution not to crush crash bar with U-bolt

Honda GL 500 Installation Manual

0

Filed Under (Honda) by admin on 21-11-2010

download
Wheel Alignment Wheel alignment is critical for proper tire wear and handling. With MiniTrike installed measure A and B . Loosen axle plates and align wheel so A and B are equal to within 1/16th of an inch. Tighten axle bolts and torque to 45 pounds. Repeat for C and D . It may be necessary to shim axle plates for proper alignment. NOTE : The measurement of A and B may not be the same as C and D. This is normal and presents no difficulty. Wheel Height / Traction Adjuster The wheel height/traction adjuster (right and left side) allows you to selectively adjust the position of your trike wheels in order to customize ride, handling, level, and traction characteristics. Your trike is shipped with the adjuster preset to an optimum position for your model of motorcycle however you can make whatever adjustments necessary to customize to your bike and personal preference. Shortening the adjuster arm raises the trike wheels and places more of the weight of your motorcycle on the motorcycle wheel. This increases motorcycle traction and gives a generally softer ride. 1) Loosen jam nuts 2) Shorten adjuster arm by turning adjuster nut A toward bolt C desired amount. 3) Turn adjuster nut B until it tightens against adjuster bracket and adjuster nut A 4) Tighten nuts A and B and jam nuts Lengthening the adjuster arm lowers the trike wheels and places more of the weight of your motorcycle on the trike wheels. This gives a firmer ride and increases handling/cornering. 1) Loosen jam nuts 2) Lengthen adjuster arm by turning adjuster nut B toward bolt D desired amount. 3) Turn adjuster nut A until it tightens against adjuster bracket and adjuster nut B 4) Tighten nuts A and B and jam nuts

Incoming search terms: