HARLEY-DAVIDSON SPORTSTER MID-LENGTH INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 07-04-2012

download
1. Find and unplug the O² sensor wires from the wiring harness and remove the ZIPSTRIP holding front O² sensor wires to the frame. Feed the end of the wire through the frame so they are free from the motorcycle. Note: pay attention to wire routing for re-installation. 2. Loosen the heat shield clamps on both the front and rear head pipe to gain easier access to the mounting nuts. 3. Remove the two head pipe mounting nuts from the flange at the heads. 4. Remove the clamp bolts that mounts the rear head pipe to the belt drive cover bracket. 5. Remove the two bolts from each muffler body where they attach to the stock mounting bracket. Carefully remove the exhaust system from the motorcycle and set aside. 6. Using a 7/8″ wrench, carefully remove the O² sensors from the stock head pipes and save for re-use on your RUSH system. 7. Remove the drive belt cover and remove the bracket off the rear cover bolt, bracket will not be re-used. 8. Loosen the brake rod at the rear eyelet using a T-30 torx socket. 9. Remove the three mounting bolts and washers attaching the exhaust mounting bracket. 10. If equipped with mid-controls, remove right side foot peg before installing your new RUSH system.

HARLEY-DAVIDSON SPORTSTER SHORTSHOTS STAGGERED INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-03-2012

download
1. Find and unplug the O2 sensor wires from the wiring harness and remove nylon cable tie holding front wire to frame. Feed the end of the wires through the frame so they are free from the motorcycle. NOTE: Pay attention to wire routing for re-installation. 2. Loosen the heat shield clamps on both the front and rear exhaust pipes. This allows easier access to the head pipe mounting nuts. 3. Remove the two head pipe mounting nuts from each fl ange, located at the cylinder head. 4. Remove the clamp bolt which mounts the rear head pipe to the belt drive cover bracket. 5. Remove the two bolts from each muffl er body where they attach to the mounting bar. Carefully remove exhaust pipes from the motorcycle and set aside. 6. Using a 7/8″ or 22mm wrench, carefully remove the O2 sensors from the stock head pipes and save for re-use with the new system. 7. Remove the drive belt cover and take the bracket off the rear cover bolt, the bracket will not be re-used. 8. Loosen the brake rod at the rear eyelet using a T30 torx driver. 9. Remove the three mount bolts and washers attaching the exhaust mounting bar (save hardware for re-use). 10. Carefully remove exhaust port fl anges and circlips from the stock exhaust system using snapring pliers. NOTE: Replace bent or damaged circlips. Check exhaust port gasket condition

HARLEY-DAVIDSON SPORTSTER SHORTSHOTS STAGGERED BLACK INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 17-03-2012

download
1. Find and unplug the O2 sensor wires from the wiring harness and remove nylon cable tie holding front wire to frame. Feed the end of the wires through the frame so they are free from the motorcycle. NOTE: Pay attention to wire routing for re-installation. 2. Loosen the heat shield clamps on both the front and rear exhaust pipes. This allows easier access to the head pipe mounting nuts. 3. Remove the two head pipe mounting nuts from each fl ange, located at the cylinder head. 4. Remove the clamp bolt which mounts the rear head pipe to the belt drive cover bracket. 5. Remove the two bolts from each muffl er body where they attach to the mounting bar. Carefully remove exhaust pipes from the motorcycle and set aside. 6. Using a 7/8″ or 22mm wrench, carefully remove the O2 sensors from the stock head pipes and save for re-use with the new system. 7. Remove the drive belt cover and take the bracket off the rear cover bolt, the bracket will not be re-used. 8. Loosen the brake rod at the rear eyelet using a T30 torx driver. 9. Remove the three mount bolts and washers attaching the exhaust mounting bar (save hardware for re-use). 10. Carefully remove exhaust port fl anges and circlips from the stock exhaust system using snapring pliers. NOTE: Replace bent or damaged circlips. Check exhaust port gasket condition. Recommended replacement exhaust port gaskets, Harley part number:17048-98 or 65324-83A.

HARLEY DAVIDSON FXD (Dyna Super Glide) TACHOMETER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
1995 Models To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative cable first) before proceeding. Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1.1995 MODELS, REMOVAL OF ELECTRONIC SPEEDOMETER AND BRACKET 1a. Refer to applicable Service Manual procedure and remove seat. 1b. Refer to applicable Service Manual procedure and remove fuel tank. Stop the engine when refueling or servicing the fuel system. Do not smoke or allow open flame or sparks near gasoline. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00002a) 1c. Remove speedometer sensor cable from mounting clips under tank. See Figure 1. The 3-place speedometer sensor connector [65] is located on the frame beneath the seat. Remove connector from t-stud and disconnect. Cut cable tie holding sensor wires to right rear frame tube. 1d. Refer to applicable Service Manual procedure and remove headlamp, for work clearance. 1e Remove handlebar clamp screws securing speedometer bracket. Remove speedometer, bracket, and harness. 2.1995 MODELS, DISCONNECT MAIN WIRING HARNESS 8-PLACE CONNECTOR [21B, A] (FIGURE 2) 2a. Disconnect the battery, negative cable first. Refer to applicable Service Manual procedure and disconnect main wiring harness 8-place connector [21A, B], at the front of the motorcycle. 3.1995 MODELS, REMOVE SPEEDOMETER LEADS FROM 8-PLACE CONNECTOR [21B, A] (FIGURE 2) 3a. See Figure 2 and Service Manual wiring schematic. Pull the following wires and terminals out of connector [21B]. Wire Color Cavity Number Orange/white 5 White/green 1 Black 2 3b. Remove the large female connector from the fuel gauge black wire. 3c. Slide the wires removed in step 2a out of the plastic conduit covering the wires connected to the 8-place connector. 1 WARNING 1 WARNING 1 WARNING Figure 1. Speedometer Sensor Connection [65] 4973 Speedometer sensor connector [65] Figure 2. Tachometer/Speedometer Wire Splices and Terminal Connections [21B, A] i00240-.tif Splices 4.1995 MODELS, REMOVE INDICATOR LAMPS FROM BRACKET 4a. Remove the screws that secure the indicator lamps assembly to the speedometer bracket. Retain screws and indicator lamps assembly for installation on speedometer/tachometer bracket later. 5.1995 MODELS, REMOVE SPEEDOMETER FROM BRACKET 5a. Unscrew boot from speedometer reset switch. Remove cover screws and rear cover. 5b. See Figure 3. Note position of rear speedometer gasket and remove it. Push on rear of speedometer while simultaneously pulling speedometer and front gasket from bracket. Do not remove front gasket from the speedometer. 6.1995 MODELS, INSTALL SPEEDOMETER IN KIT BRACKET 6a. See Figure 5. Place wires from speedometer through front of left opening in double bracket. Lubricate the front and rear gaskets with isopropyl alcohol or glass cleaner to ease installation. 6b. Insert speedometer into the front of the double bracket. Be sure wire guides are aligned with opening at bottom of bracket. 6c. Place rear gasket in position and align gasket tabs. Work gasket into space between speedometer and bracket by pushing speedometer against one side of bracket while pushing gasket into position at the opposite side. 6d. Add amber bulb assembly from kit to speedometer in order for tachometer and speedometer backlighting to match. 6e. Replace cover and boot from reset switch.

Incoming search terms:

HARLEY DAVIDSON TOURING MODEL DRESSER DUALS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 24-12-2010

download
1. Remove both left and right saddlebags and set them aside. 2. Loosen the bolt from the pinch clamp on the front end of each muffl er. 3. Remove the two 5/16″ bolts that mount the muffl er to the saddlebag supports. Repeat this step on the opposite muffl er (save these parts, they will be re-used). 4. Remove the stock muffl ers with sliding hangers and set them aside. NOTE: It may be necessary to use a penetrating lubricant to loosen the muffl er from the head pipe. 5. Find and unplug the O2 sensor wires from the wiring harness and remove cable tie holding front wire to frame. F eed the end of the wires through the frame so they are free from the motorcycle. NOTE: Pay attention to wire routing for re-installation. 6. Remove the right hand fl oor board. 7. Remove both passenger fl oor boards. 8. Loosen the heat shield clamps on both front and rear exhaust pipes. 9. Loosen the rear head pipe clamp located behind the rear cylinder. Remove the section of head pipe connecting the left side muffl er. 10. Remove the nut and carriage bolt holding the front head pipe to the bracket on the transmission housing (save these parts, they will be re- used). 11. Remove the two mounting nuts from each head pipe, located at the cylinder head. Carefully remove the head pipes and set them aside. 12. Using a 22mm wrench, carefully remove the O2 sensors from the stock head pipes and save for re-use with the new system. 13. Remove the rear cylinder bracket by removing the two starter mounting bolts. Install new bracket (stamped 422-P)(supplied) and torque to 13-16 ft. lbs. (Figure 1). NOTE: Twist breather hose down towards the left hand side to get it as far away from the pipe as possible. 14. Install mounting post (from stock system) so the nut is accessible from right side of motorcycle and saddle will support underside of exhaust pipe. 15. Replace the bracket on the transmission housing with new bracket (stamped 423-P)(supplied) and torque to 13-16 ft. lbs. (Figure 2). 16. Carefully remove the exhaust port fl anges and circlips from the stock exhaust system using snapring pliers. NOTE: If circlips look bent or twisted, replace them.