2009 Harley-Davidson FLH Series Independent Suspension Trike Conversion Installation Manual

0

Filed Under (Harley Davidson) by admin on 16-02-2011

download
Important Safety Precautions a. Make sure you have a clear understanding of all basic shop safety practices and that you wear appropriate clothing and use safety equipment. Be especially careful of the following: · Read all directions before you begin, and make sure you have the tools, the parts and the skills required to perform the tasks safely and completely.Harley-Davidson® FLH 2009 & Up Independent Suspension CHAMPION TRIKES Installation Guide Page 5 of 18 Revision 8 · Protect your eyes by using proper safety glasses, goggles or face shields anytime you hammer, drill, grind, pry or work around pressurized air or liquids, and springs or other stored-energy components. · Use other protective wear when necessary, for example gloves or safety shoes. Handling hot or sharp parts can cause severe burns or cuts. · Protect yourself and others when you have a vehicle up in the air. Anytime you lift a vehicle, either by hoist or a jack, make sure that it is securely supported. b. Make sure the engine is turned off and battery disconnected before you begin work. · Carbon Monoxide poisoning from exhaust gases: Be sure there is adequate ventilation whenever you run the engine. · Burns from hot parts: Let the engine and exhaust system cool before working on those areas. · Injury from moving parts: If running the engine, keep hands, fingers and clothing away from moving/rotating parts. c. Gasoline vapor and hydrogen gases from batteries are explosive. To reduce the possibility of fire or explosion, be careful when working near gasoline and batteries. d. Use only nonflammable solvent, not gasoline, to clean parts. e. Never drain or store gasoline in an open container. f. Keep all cigarettes, sparks or flame away from the battery and all fuel related parts. 1.6 Specifications Overall Length: 103″ Overall Width: 57.25″ Wheel Base: 53″ Max Load Capacity: 600 Lb Max Tire Size (15″): 205 / 70 / R15 Wheel Size (15″) (4 lug) Offset +35 mm 15x7JJ 4 on 4.5 Tire Pressure: 24-26 PSI Suspension: Double A-arm Independent Rear Differential: Custom-built rear differential utilizing OEM drive belt. Brakes: Original front plus 2 high performance disc brakes at rear. Storage Capacity: 5.75 cubic feet. Two full-face helmets and additional storage. *Champion does not change certain components that will affect EPA, CARB, or any laws that will change the emission characteristics of the motorcycle.

Incoming search terms:

8950 and 8960 Series High Performance Tire Changer Operation Manual

0

Filed Under (Tips and Review) by admin on 23-11-2010

download
GENERAL CAUTIONS A. DURING THE USE AND MAINTENANCE OF THE MACHINE IT IS MANDATORY TO COMPLY WITH ALL LAWS AND REGULATIONS FOR ACCIDENT PREVEN- TION. B. THE ELECTRICAL POWER SOURCE MUST HAVE A GROUND CABLE AND THE GROUND CABLE OF THE MACHINE MUST BE CONNECTED TO THE GROUND CABLE OF THE POWER SOURCE. C. BEFORE ANY MAINTENANCE OR REPAIRS ARE ACCOMPLISHED THE MACHINE MUST BE DISCONNECTED FROM THE AIR AND ELECTRICAL SUPPLY. D. NEVER WEAR TIES, CHAINS OR OTHER LOOSE ARTICLES WHEN USING, MAINTAINING OR REPAIRING THE MACHINE. LONG HAIR IS ALSO DANGEROUS AND SHOULD BE KEPT UNDER A HAT. THE USER MUST WEAR PROPER SAFETY ATTIRE – GLOVES, SAFETY SHOES AND GLASSES. 2.0 INSTALLATION Your new JBC 8950 or 8960 Series Tire Changer requires a simple installation procedure requiring only a few moments. Follow these instructions carefully to insure proper and safe operation. The Tire Changer is delivered mounted to a wooden skid. Remove tire changer from its mounts carefully, taking care to avoid any back strain. Place Changer where proper operation will be unobstructed to all sides. Install the machine in a covered and dry place. 2.0.1 Models with SRA attached (8955IN, 8965IN) Once placed in the desired location the tire changer must be bolted to the floor using only the rear two mounting holes. Mounting anchors are provided with those machines with a Safety Restraint Arm. Tire Changer must be anchored to concrete floor if equipped with a “Safety Restraint Arm” BUILDING ELECTRICAL INSTALLATION MUST BE MADE BY A LICENSED ELECTRICIAN. Check that the electrical specifications of the power source are the same of the machine. The machine uses 110v, 60 hz, single phase 20 amp source. Electric specifications are clearly marked on a label at the rear of the machine. FAILURE TO PROVIDE PROPER ELECTRICAL SUPPLY AND GROUNDING WILL CREATE A SHOCK HAZARD TO THE OPERATOR

Incoming search terms:

Incoming search terms: