HARLEY DAVIDSON SISSY BAR SIDE PLATE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-02-2011

download
INSTALLATION NOTE When removing rear fender reflectors, be careful not to damage fender paint. 1. Carefully remove the rear reflector. Remove any remaining adhesive from the back side of the reflector and any adhesive from the side of the fender. 2. See Service Parts Illustration. Remove the screws, washers, locknuts and clipnuts that attach the fender support cover and fender support to fender. Discard the button head screws but retain the washers (A), locknuts (B,C) and clipnuts (D) for installation. NOTE Prior to performing the following step, obtain a little slack for the turn signal assembly by reaching under the fender and bending open the aluminum tab on the clip securing wiring to fender. 3. Remove the locknut (B) from the turn signal stud (E) and gently remove the turn signal assembly from fender support cover, fender support and fender. Save locknut for installation. The turn signal will remain loosely attached to motorcycle by rear directional wire. 4. Carefully position the side plate between fender support and fender. While holding sideplate in position, line up the screw mounting holes and make sure the turn signal wiring passes through the cutout (slot) in the side plate. Coat threads of screws (1 and 2) from kit with Loctite 243 (blue) (Harley-Davidson part number 99642-97) and install locknut and clipnut, however do not tighten completely. 5. Add Loctite 243 (blue) (Harley-Davidson part number 99642-97) to turn signal stud and install through fender support cover, fender support, side plate and fender. Install locknut and tighten to 8-13 ft-lbs (11-18 Nm). Making sure sideplate remains aligned, return to fender support screws and tighten to 8-13 ft-lbs (11-18 Nm). 6. Reach under fender and position turn signal wiring into tab on clipnut. 7. Obtain reflector (3) from kit. Peel off protective strip backing and firmly press reflector (3) to side plate (4), centering reflector horizontally and vertically. 8. Repeat steps 1 through 7 on opposite side of fender

HARLEY DAVIDSON SOFT LOWER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-02-2011

download
This kit fits 1980 and later Touring models equipped with engine guards. It does not fit with mustache engine guards INSTALLATION NOTE Soft lowers should not be used in temperatures above 55 degrees Fahrenheit. Engine cooling air flow will be affected and could lead to overheating and possible engine damage. 1. Apply a light coating of silicone grease to cavities of snaps prior to installing soft lowers on motorcycle. 2. See Figure 1. An opening is provided in the soft lowers for mounting highway footrests (1) to engine guard. If using footrests, mount within the opening to prevent buckling of splash guard fabric. 4. Remove adhesive liner from back of reflector. NOTE The ideal temperature should be at least 60° F (16° C) for proper adhesion of the reflectors. 5. Place reflector on fender and press firmly into position. 6. Let the adhesive cure for 24 hours at no less than 60° F (16° C). 7. Repeat steps for other reflector

HARLEY DAVIDSON SOFTAIL SADDLEBAG KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
INSTALLATION Do not exceed saddlebag weight capacity. Put equal weight in each bag. Too much weight in saddlebags can cause loss of control, which could result in death or serious injury. (00383a) NOTES Maximum saddlebag weight capacity is 7 lbs (3.18 kg) for each bag. Proper installation of these kits requires that tasks be completed for one side of the motorcycle first before continuing to the opposite side. 2000-2002 Models with Wide Tire Kit 1. See Figure 1. Remove and discard stock screws (1) and washers (2) from fender support. Button head screws from wide tire kit must be installed with button heads on inside of fender. Fastener contact with tire can lead to premature tire failure, which could result in death or serious injury. (00417b) 2. See Table 3. Determine appropriate screw from wide tire kit. 3. See Figure 2. Install saddlebag using screw (from wide tire kit) (1), washer (2) and nut (3). The screws are installed from inside to outside of fender. NOTE If you do not have the appropriate screw from the wide tire kit, it can be purchased from a Harley-Davidson dealer. Table 3. Wide Tire Kit Screws (3/8-16) Wide Tire Kit 44490-00, Hardware Kit 43763-00 Wide Tire Kit 44490-00, Hardware Kit 43761-00 Part Number and Length X X 4030 – 2-1/2 inch X X 4225 – 3-1/2 inch X X 4224 – 1-1/2 inch X X 4044 – 1-1/4 inch X 4215 – 2 inch X 3912 – 2-3/4 inch X X 4228 – 2-1/4 inch X X 4229 – 3-1/4 inch Failure to tighten saddlebag mounting bolts to specified torque could result in damage to saddlebags. (00406c) 4. Tighten all saddlebag hardware to 22 ft-lbs (30 Nm). NOTE Check that front screws have at least one thread exposed beyond the nut after proper torque has been applied. 5. Install reflectors on saddlebag. Refer to Install Reflectors subtopic.

HARLEY DAVIDSON SOFTAIL RIGID MOUNT SADDLEBAGS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
INSTALLATION NOTE Maximum saddlebag load is 10 lbs. (4.5 kg) for each bag. Do not exceed saddlebag weight capacity. Put equal weight in each bag. Too much weight in saddlebags can cause loss of control, which could result in death or serious injury. (00383a) NOTE Saddlebag hangers must be mounted with the bend in the hanger facing out from the motorcycle. NOTE The saddlebags are symmetrical and can be mounted on either side. 1. See Figure 1. Remove the fender support cover screws from locations shown for mounting saddlebags. 2. Place lock washers (6) on two cap screws (5) and insert through the top holes of the saddlebag hanger. NOTE The FXSTC Does Not use narrow spacers (8) in Step 3 for the saddlebag installation. 3. With the cap screws in place on the hanger, place a wide spacer (7) followed by a narrow spacer (8) on each screw. 4. Thread the cap screws into the location of the original screws previously removed in Step 1 and tighten screws to 22 ft-lbs (30 Nm) . 5. From the inside of the saddlebag install two button head screws (2) with washers (3) through the upper mounting holes in the saddlebag and the hanger. 6. On the backside of the hanger install hex nuts (4) to the screws from previous step and tighten to 22 ft-lbs (30 Nm) . 7. Insert two button head screws through the lower two holes on the backside of the hanger and into the saddlebag. 8. From the inside of the saddlebag install washers and hex nuts to screws and tighten to 22 ft-lbs (30 Nm) . 9. Repeat Steps 1 through 8 for installation of the other saddlebag. Installation with Docking Points 1. If you choose to use the docking points from Kit 53930- 03, repeat the installation of previous Steps 1-8 and substitute the front and rear docking points for the spacers (7) in this Kit. You must use narrow spacers (8) from this kit for both the FLSTSB and the FXSTC when using the docking points. Install Reflectors

HONDA VTX 1800 CHROME RADIATOR COVER INSTALLATION

0

Filed Under (Honda) by admin on 29-12-2010

download
Remove the amber reflectors from the sides of the stock plastic radiator cover. These can be pried off carefully using a wide screwdriver blade or small putty knife. 2. Remove the 3 allen screws from the stock plastic radiator cover, 2 on top and 1 on the bottom. 3. Slide the chrome radiator cover over the stock plastic cover. 4. Re-Install the two original upper screws into the top holes. In the bottom hole install the button head allen screw and washer provided. Tighten all three screws. Firmly press the reflectors back onto the chrome cover