Kawasaki ZX-9R Ninja TiForce exhaust system Installation Instructions

0

Filed Under (Kawasaki) by admin on 07-05-2012

download
1. Remove the lower fairing. Remove thelower radiator mounting bolts, loosen the upper bolts and pivot the radiator forward to provide access to the exhaust nuts (flange nuts). Remove the oil cooler mounting bolts and pivot the oil cooler forward to provide access. 2. Remove the existing exhaust system and save the flange nuts for reuse. Save the stock exhaust can mounting bolt and nut for reuse as well. 3. Inspect the exhaust gaskets. Replace if necessary. 4. Assemble the head pipes 1 (blue), 2 (red), 3 (yellow), and 4 (green) by matching the joints of the same color to the pair of front Y-pipes. Do not install the exhaust springs at this time. 5. 2000 through 2002 models ONLY!!! Place a billet aluminum exhaust port centering flange Z on each TiForce headpipe -see figure 3 for details. 6. Attachthe assembled head pipe sections to the exhaust ports, but do not tighten the flange nuts fully, allowing for some adjustment in the remaining steps. Reuse the flange nuts saved from step 2 above. Make sure the ends of the headpipes fit flush and snug in the ports and centering flanges Z before tightening (’00-’02 ONLY). 7. Install the S-Bend to the front section of the headpipes and two Y-pipes. 8. Go back and retighten the head pipe flange nuts per factory specifications -make sure the headpipes and flanges Z are centered in each port (’00-’02 ONLY!!! ) . 9. Slide the TiForce end can into place. 10. Loosely attach the two rubber bands, stainless steel bands K, and stay / hanger G to the end can using the supplied 6mm hardware H. See figure 1. 11. Place the bands approximately 108 mm from the edge of the end can. See figure 2. 12. Using the stock provided mounting point on the passenger footpeg, and using the stock mounting bolt, mount the end can loosely, allowing for some adjustment. Insert the stock mounting bolt through the stay / hanger G. 13. Attach the supplied springs to all the joints, starting from the headpipes and working back to the end can. 14. Make sure the exhaust system is free and clear, if necessary jiggle the system to adjust for proper clearance. 15. Carefully align the two stainless bands K so that they are parallel to each other, and spaced properly on the can (refer to step 11 /figure 2), then tighten the 6mm hardware H and the stock mounting bolt hardware. Make sure that the rubber pads fully cover the band(s). USE CAUTIONWHEN TIGHTENING THE 6MM HARDWARE AND THE TWO BANDS SO AS NOT TO CRUSH OR DISTORT THE SLEEVE OF THE CAN.

Yamaha TDM 900 Disconnecting the battery ground REMOVAL AND INSTALLATION

0

Filed Under (Yamaha) by admin on 29-01-2012

download
Remove the seat. • Disconnect the battery ground (negative terminal). Remove the fairing side panels. • Remove the four marked hex screws with plastic washers. Note the positions the screws come from as they are not all the same. • Note that the bottom, rear hex bolt has a retaining plastic washer INSIDE the fairing. The long bolt goes under the ‘twin’ label. • Remove the hex screw indicated on the inside of the fairing panel. • Remove the grey Phillip’s head screw as indicated on the inside panel. • Remove the plastic locking clip on the underside of the fairing behind the radiator.

R1 Addendum Yamaha YZF-R1 and YZF-R6 TiForce exhaust system REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 11-01-2012

download
Remove the lower fairing. Remove the lower radiator mounting bolts, loosen the upper bolts and pivot the radiator forward to provide more access to the exhaust nuts (flange nuts). 2. YZF-R1 ONLY!!! The EXUP control cables are tie-wrapped to the frame, and will need to be disconnected from the servo motor. Do not disconnect the electrical connection to the servo motor, and do not remove the actual servo motor. Simply remove the cables from the EXUP valve and from the servo motor. 3. Remove the existing exhaust system and save the flange nuts for reuse. Save the mounting bolt and nut for the end can to the passenger footpeg for reuse as well. 4. Inspect the exhaust gaskets. Replace if necessary. 5. Assemble the head pipes 1 (blue), 2 (red), 3 (yellow), and 4 (green) by matching the joints of the same color to the pair of front Y-pipes. Do not install the exhaust springs at this time. 6. Attach the assembled head pipe sections to the exhaust ports, but do not tighten the flange nuts fully, allowing for some adjustment in the remainingsteps. Reuse the flange nuts saved from step 3 above. Make sure the ends of the headpipes fit flush and snug in the ports before tightening. 7. Install the S-Bend to the front section of the headpipes and two Y-pipes. 8. Go back and retighten the head pipe flange nuts per factory specifications. 9. Slide the TiForce end can into place. Loosely attach the two rubber bands, stainless steel bands K, and stayarm / hanger G to the end can using the supplied 6mm hardware H. See figure 1. 10. YZF-R1 ONLY!!! Place the bands approximately 180mm from the edge of the end can. See figure 2. 11. YZF-R6 ONLY!!! Place the bands approximately 195mm from the edge of the end can. See figure 2. 12. Using the stock provided mounting point on the passenger footpeg, and using the stock mounting bolt, mount the end can loosely, allowing for some adjustment. Insert the stock mounting bolt through the stay / hanger G. 13. Attach the supplied springs to all the joints, starting from the headpipes and working back to the end can. 14. Make sure the exhaust system is free and clear, if necessary jiggle the system to adjust for proper clearance. 15. Carefully align the two stainless bands K so that they are parallel to each other, and spaced properly on the can (step 10 or 11 / figure 2), then tighten the 6mmhardware H and the stock mounting bolt hardware. Make sure that the rubber pads fully cover the band(s). USE CAUTION WHEN TIGHTENING THE 6MM HARDWARE AND THE TWO BANDS SO AS NOT TO CRUSH OR DISTORT THE SLEEVE OF THE CAN

HONDA CR 500R/ 500AF Hi Power Digital Ignition AND Light Coil Installation Instructions

0

Filed Under (Honda) by admin on 16-12-2011

download
Place the motorcycle on a secure stand. 2.Remove the fuel tank and radiator shrouds. 3.Remove the front number plate if CDI unit is located behind number plate. 4.Remove CDI Ground from coil. 5. Remove Old CDI. 6. Remove ignition cover. 7. Use an electric, pneumatic impact to remove flywheel nut. 8. Use flywheel puller to remove flywheel. Thread the flywheel puller into the flywheel by turning the puller counter clockwise (left hand thread). Turn flywheel puller center nut clockwise with an impact set to low to remove flywheel. 9. Remove 2 bolts that secure the stator.
10. Remove stator. 11. Install new stator by aligning the index mark on the lower stator plate with the index mark on the left crankcase. 12.Install and tighten stator bolts to 9 ft-lbs. (1.2 kg-m). 13. Install new flywheel and tighten flywheel nut to 40ft-lb (5.5 kg-m). 14. The pulser gap is preset to .012″. If you have trouble starting you bike after installation confirm the gap between the pulser and the ignition trigger on the flywheel is .012″. Use a good/no good technique when checking and adjusting the gap. The largest feeler that will fit without forcing the feeler into the gap is the current gap. 15. If the pulser gap needs to be adjusted loosen the pulser mounting bolts adjust the pulser up or down as needed

HONDA XR 250 1996 Dual Sport Kit Installation Manual

0

Filed Under (Honda) by admin on 06-12-2011

download
Get a degree in Mechanical and Electrical Engineering. (Just kidding!) 2. Remove the seat, side panels, radiator shrouds, and gas tank.
If you are color blind or even think you might be a little color blind, now is the time to get someone to assist you. Successful installation of the kit requires good color recognition. You want to go riding this weekend, don’t you? 3. Unplug the green and blue taillight wires from the stock wiring harness, remove the taillight lens, and remove the taillight socket and wiring. 4. Unplug the headlight from the stock wiring harness and remove. 5. Remove the kill switch. Unplug the black/white wire and the black wire from the connector near the base of the odometer. AC Regulator Unplug taillight here Photo 1 6. Locate the AC voltage regulator found mounted on the front top edge of the airbox as shown in Photo 1. Unplug the regulator from the wiring harness and remove regulator (Leave the U-bolt
attached to the airbox and save the bolt for a later step)

1994-1998 HONDA RVF400RR Racing Kit INSTALLATION

0

Filed Under (Honda) by admin on 01-12-2011

download
(1)Fuel High Octane white gasoline (2)Engine Oil Recommended Oil: HONDA Ultra-GP (for four-cycle Motorbike) SAE20W-50 or 10W-40
Full Capacity: 3.0Liter (5.28pt) Oil Exchange: 2.5Liter (4.4pt) Filter Exchange: 2.4Liter (4.224pt) (3)Spark Plug NGK R 847-10(11)(4)Cooling Water Highly recommend checking the water level on each ignition/riding. Ingredient: Tapped water or Drinking water I. Unscrew a radiator cap. Apply water up to limb of intake. II. Hold steering and heave the body two or three times to let air out. III.Add water if necessary. IV. Screw the cap tighten.V. Start Engine then check water level again. Add water if necessary. < Notes for racing condition> • Keep your attention when you re-check the water level since the water would spill out of intake. Also cover the body with wastes. • Drain cooling water in a catch-tank before riding. • Drain whole water in a radiator after riding. It avoids corrosion or clog of components. • It is admitted adding coolant in winter season. Handle carefully when you apply them. It makes the circuit slippery if it drops or spilled.

CR500R/ 500 AF Hi Power Digital Ignition & Light Coil Installation Instructions

0

Filed Under (Honda) by admin on 19-11-2011

download
Place the motorcycle on a secure stand. 2.Remove the fuel tank and radiator shrouds. 3.Remove the front number plate if CDI unit is located behind number plate. 4.Remove CDI Ground from coil. 5. Remove Old CDI.b6. Remove ignition cover. 7. Use an electric, pneumatic impact to remove flywheel nut. 8. Use flywheel puller to remove flywheel. Thread the flywheel puller into the flywheel by turning the puller counter clockwise (left hand thread). Turn flywheel puller center nut clockwise with an impact set to low to remove flywheel. 9. Remove 2 bolts that secure the stator. 10. Remove stator. 11. Install new stator by aligning the index mark on the lower stator plate with the index mark on
the left crankcase. 12.Install and tighten stator bolts to 9 ft-lbs. (1.2 bkg-m). 13. Install new flywheel and tighten flywheel nut to 40ft-lb (5.5 kg-m). 14. The pulser gap is preset to .012”. If you have trouble starting you bike after installation confirm the gap between the pulser and the ignition trigger on the flywheel is .012”. Use a good/no good
technique when checking and adjusting the gap. The largest feeler that will fit without forcing the feeler into the gap is the current gap

Honda CBR-1100xx Blackbird – Installation and Removal Instructions

0

Filed Under (Honda) by admin on 03-11-2011

download
Remove the lower fairing. Remove the lower radiator mounting bolts, loosen the upper bolts and pivot the
radiator forward to provide access to the exhaust nuts (flange nuts). Remove the oil cooler mounting bolts and
pivot the oil cooler forward to provide access.
2. Remove the existing exhaust system and save the flange nuts for reuse. Save the stock exhaust can mounting
bolt and nut for the end can to the passenger footpeg for reuse as well.
3. Inspect the exhaust gaskets. Replace if necessary.
4. Assemble the head pipes 1 (blue), 2 (red), 3 (yellow), and 4 (green) by matching the joints of the same color to
the pair of front Y-pipes. Do not install the exhaust springs at this time.
5. Remove the rubber center stand stop from the stock exhaust system. Insert the rubber stop into the supplied
steel bracket. Mount the bracket to the right side of centerstand using the stock mounting bolt, and tighten fully.
6. Attach the assembled head pipe sections to the exhaust ports, but do not tighten the flange nuts fully, allowing
for some adjustment in the remaining steps. Reuse the flange nuts saved from step 2 above. Make sure the
ends of the headpipes fit flush and snug in the ports before tightening.
7. Install the S-Bend to the front section of the headpipes and two Y-pipes.
8. Go back and retighten the head pipe flange nuts per factory specification.
9. Slide the TiForce end can into place.
10. Loosely attach the two rubber bands, stainless steel bands K, and stay / hanger G to the end can using the
supplied 6mm hardware H. See figure 1.
11. Place the bands approximately 115mm from the edge of the end can. See figure 2.
12. Using the stock provided mounting point on the passenger footpeg, and using the stock mounting bolt, mount
the end can loosely, allowing for some adjustment. Insert the stock mounting bolt through the stay / hanger G.
13. Attach the supplied springs to all the joints, starting from the headpipes and working back to the end can. Please

1995 – 2004 Toyota Tacoma Body Lift Kit Installation and REMOVAL

0

Filed Under (Toyota Manuals) by admin on 24-09-2011

Download
RADIATOR FAN SHROUD: Only raise body high enough to remove and replace body mounts. Always watch the fan shroud for sufficient clearance when raising the body. 2. Remove the 12mm bolts and nuts from the upper steering coupler on the rack and pinion noting the position of the steering column. Note: do not let the steering column turn, keep the column and rack aligned to its original position, mark if necessary. See figure 2. 3. Loosen body mount bolts on the driver’s side of vehicle and remove bolts from opposite side for positions 1,2 and 3, see Figure 1. Place a 2×4 between the jack and body to pread out load. 4. Raise the body on the driver’s side just far enough to remove mounts. Temporarily prop up the cab between cab and the frame with a wooden 2×4 or spacer. (This is to avoid cab from falling while working on body mounts.) The bolts on the opposite side will help ensure that the body does not shift. Make sure cab doesn’t contact bed when lifting. 5. Remove factory mounts one at a time.
6. Install the new S10321 steel bracket, polyurethane body mounts, and steel sleeves in positions 1, 2 and 3. Refer to the diagrams for positions. NOTE: On 2001 and newer models you will need to invert the #2 position bushings so that the M02787 is on top. 7. Install the supplied aluminum steering coupler with the round bosses pointing down. Note: you may have to loosen the pinch bolt at the top of the steering coupler so that it will slide up enough to install the steering coupler. See figure 2. 8. Lower the driver’s side and START the new bolts into the new mounts. Reconnect the steering coupler with the supplied 5/16” bolts from the top and nuts. DO NOT TIGHTEN!
9. Now remove bolts from passenger side of vehicle and repeat steps 3 through 6. 10. Tighten the steering coupler bolts and nuts to 35ft lbs also tighten the upper steering bolt to 35ft lbs

1990- 1995 TOYOTA 4RUNNER BODY LIFT KIT INSTALLATION INSTRUCTIONS KIT

0

Filed Under (Toyota Manuals) by admin on 22-09-2011

Download
Disconnect both battery cables. Disconnect negative cable first, then positive cable Disconnect and move radiator out of the way. . Remove overflow hose from radiator spout. b. Remove four bolts securing radiator to core sup-port. c. Lift radiator up out of slots in core support. d. Straighten tabs on radiator. e. Lay radiator on fan while lifting body. 3. Relocate alternator ground strap if equipped Adhere to recommendations when replacement fasten-
ers, retainers and keepers are called out in the factory service manual. When re-assembling the vehicle it is recommended by the vehicle manufacturer that certain fasteners are replaced in order to maintain proper
retention characteristics. This system may not include all replacement hardware as recommended by the fac-
tory service manual. Additional replacement hardware should be obtained prior to installation of this system to
meet the requirements of the factory service manual.