Kawasaki ZX-9R Ninja TiForce exhaust system Installation Instructions

0

Filed Under (Kawasaki) by admin on 07-05-2012

download
1. Remove the lower fairing. Remove thelower radiator mounting bolts, loosen the upper bolts and pivot the radiator forward to provide access to the exhaust nuts (flange nuts). Remove the oil cooler mounting bolts and pivot the oil cooler forward to provide access. 2. Remove the existing exhaust system and save the flange nuts for reuse. Save the stock exhaust can mounting bolt and nut for reuse as well. 3. Inspect the exhaust gaskets. Replace if necessary. 4. Assemble the head pipes 1 (blue), 2 (red), 3 (yellow), and 4 (green) by matching the joints of the same color to the pair of front Y-pipes. Do not install the exhaust springs at this time. 5. 2000 through 2002 models ONLY!!! Place a billet aluminum exhaust port centering flange Z on each TiForce headpipe -see figure 3 for details. 6. Attachthe assembled head pipe sections to the exhaust ports, but do not tighten the flange nuts fully, allowing for some adjustment in the remaining steps. Reuse the flange nuts saved from step 2 above. Make sure the ends of the headpipes fit flush and snug in the ports and centering flanges Z before tightening (’00-’02 ONLY). 7. Install the S-Bend to the front section of the headpipes and two Y-pipes. 8. Go back and retighten the head pipe flange nuts per factory specifications -make sure the headpipes and flanges Z are centered in each port (’00-’02 ONLY!!! ) . 9. Slide the TiForce end can into place. 10. Loosely attach the two rubber bands, stainless steel bands K, and stay / hanger G to the end can using the supplied 6mm hardware H. See figure 1. 11. Place the bands approximately 108 mm from the edge of the end can. See figure 2. 12. Using the stock provided mounting point on the passenger footpeg, and using the stock mounting bolt, mount the end can loosely, allowing for some adjustment. Insert the stock mounting bolt through the stay / hanger G. 13. Attach the supplied springs to all the joints, starting from the headpipes and working back to the end can. 14. Make sure the exhaust system is free and clear, if necessary jiggle the system to adjust for proper clearance. 15. Carefully align the two stainless bands K so that they are parallel to each other, and spaced properly on the can (refer to step 11 /figure 2), then tighten the 6mm hardware H and the stock mounting bolt hardware. Make sure that the rubber pads fully cover the band(s). USE CAUTIONWHEN TIGHTENING THE 6MM HARDWARE AND THE TWO BANDS SO AS NOT TO CRUSH OR DISTORT THE SLEEVE OF THE CAN.

HARLEY DAVIDSON SOFTAIL OIL COOLER KIT WITH CHROME OIL COOLER COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download
INSTALLATION 1. See Figure 1. Install the oil cooler (2) to the frame with three clamps (4), three socket head screws (1), three nuts (5) and six washers (3) from the kit. Orient the clamps flat side forward and on the forward side of the oil cooler. Tighten the three oil cooler mounting screws to 96-120 in- lbs (10.9-13.5 Nm) . 2. See Figure 2. Remove the spin-on oil filter and oil filter adapter (1) from oil filter mount location. Clean the oil filter mounting area thoroughly. Discard oil filter and adapter. 1 3 4 4 4 3 5 2 is03387 1. Socket head screw (3) 2. Oil cooler 3. Washer (6) 4. Clamp (3) 5. Locknut (3) Figure 1. Oil Cooler Clamp Installation NOTE The oil cooler adapter assembly has two flanges protruding out of the back side. The flanges must be installed toward the oil filter mounting location and through the oil adapter gasket. 3. See Figure 3. From the kit, install the oil cooler adapter gasket (3) onto the oil cooler adapter assembly (1). The oil cooler adapter assembly flanges should be aligned so it is installed into the oil adapter cooler gasket cutout as shown. NOTE Due to the locating flanges, the oil cooler adapter assembly and gasket will only install properly in one position on the oil filter mounting surface. 4. See Figure 3. Install the oil cooler adapter assembly and gasket onto the oil filter mounting surface of the engine with the mounting fitting (2). Ensure adapter locates properly in the mounting surface. Ensure the raised lip of the mounting fitting faces the adapter assembly. Tighten mounting fitting to 12-16 ft-lbs (16.3-21.7 Nm) .NOTE Slide hose clamps from the kit onto the hoses prior to installa- tion. 1 2 is00754 1. Oil filter adapter 2. Oil filter seal surface Figure 2. Stock Filter Mounting Adapter 1 2 3 is00761 1. Oil cooler adapter assembly 2. Mounting fitting 3. Oil cooler adapter gasket Figure 3. Install Oil Adapter 5. See Figure 5. Obtain the left side cooler hose (4) and right side cooler hose (5) from kit. Follow the markings on hoses to connect onto the oil cooler and oil cooler adapter, as shown. 6. Fasten hoses to oil cooler adapter and oil cooler with worm drive clamps (6). Tighten clamps to 8.0 in-lbs (0.9 Nm) . 7. Lubricate a new oil filter’s seal with new engine oil. Thread filter on until seal touches mounting surface, then turn an additional 1/2 to 3/4 turn. NOTE Position the clamps to avoid interference with oil filter installation. Check that hose routing is clear of the oil filter and sharp edges. The hoses must be free of bends or kinks that could obstruct oil flow. 8. Ensure all cables and harnesses are clear of the oil cooler adapter, in order to prevent wear. 9. Thoroughly clean the oil cooler of all dirt, grease and wax with isopropyl alcohol. Use the alcohol to clean the chrome oil cooler cover as needed. Allow to dry. is00745 Figure 4. Apply Sealant Inside Chrome Cover 10. See Figure 4. Apply sealant to the inside of the chrome cover as shown, at the upper and lower corners. NOTES Be careful to avoid getting sealant on the oil cooler cooling fins. Do not operate the motorcycle for 24 hours to allow the sealant to fully cure. 11. Slip the cover over the oil cooler. Remove any excess sealant from the front and back of the oil cooler. Hold the cover firmly in place for one minute. System Flow Test 2005 & Later Models or Models with Later Style Dipsticks Oil level cannot be accurately measured on a cold engine. For pre-ride inspection, with motorcycle leaning on jiffy stand on level ground, oil should register on dipstick between arrows when engine is cold. Do not add oil to bring the level to the FULL mark on a COLD engine. (00185a) 2004 & Earlier Models

Incoming search terms:

HARLEY DAVIDSON CHROME OIL COOLER COVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 03-02-2011

download
INSTALLATION 6 2 1 3 5 4 is04287a 1. Oil Cooler 2. Guard 3. Stock Washer 4. Stock Nut 5. Mounting Bracket 6. Area to Apply Heat Figure 1. Oil Cooler Preparation Be sure to follow manufacturer’s instructions when using the Robinair Heat Gun or any other radiant heating device. Failure to follow manufacturer’s instructions can cause a fire, which could result in death or serious injury. (00379a) 1. See Figure 1. Remove the oil cooler guard (2) from the oil cooler (1) by using the Heat Gun (or equivalent) to apply heat to the top surface. Pull the guard away from the oil cooler and discard. 2. Remove and discard the three locknuts (4) and flat washers (3) fastening the oil cooler to the mounting bracket (5). 3. Raise the oil cooler slightly to separate the studs on the underside of the oil cooler from the mounting bracket. 4. See Figure 2. Place the oil cooler cover (1) onto the oil cooler studs, between the oil cooler and the mounting bracket. 5. Lower the oil cooler and cover into the holes in the mounting bracket. 6. Place a new flat washer and locknut from the kit onto each stud. Line the oil cooler cover up squarely against the oil cooler, and tighten the locknuts to 80-100 in-lbs (9.1-12.4 Nm) . SERVICE PARTS

VICTORY HAMMER, KINGPIN, VEGAS AND JACKPOT ELECTRIC HORN INSTALLATION INSTRUCTIONS

0

Filed Under (Victory) by admin on 29-01-2011

download
1. Remove the left and right plastic side covers and the seat (two allen bolts located below the sides of the seat). Unplug and remove the stock horn (located over the oil cooler). Connect the female ends of the jacketed two wire cable supplied to the original horn wires. Route the other end of the cable up over the engine and back to where the relay will mount as shown in photo (1). 2. Using the relay supplied with this kit and the wiring diagram provided with the horn set, identify the terminals of the relay (there are very small numbers next to each of the terminal). Connect the two (2) wires from the cable to terminals #85 & 86 on the relay. Locate the fuse holder wire assembly supplied and connect the blade terminal to the relay terminal #87 or #30. Connect the other end of the fuse wire to the battery positive terminal (+). 3. Working under the left side of the motorcycle, refer to photo (2) and install the black bracket supplied as shown onto the engine mount. Locate the four thin flat brackets and two (2) 6mm nuts supplied with the horn set and two lock washers supplied with the kit. Bolt two (2) of the brackets to each of the horns using a lock washer and 6mm nut on each and make them snug. Using the remaining 6 x 12mm bolt, nut and lock washer install the horns onto the black bracket and align as shown in photo (3). Adjust the horn location so that they are free to vibrate and do not come in contact with other parts of the motorcycle then tighten all three 6mmm bolts securely. 4. Using the two remaining wire assembles supplied, connect the larger terminals with double wires to one of the horns and the terminals with the single wire to the other horn. Route these wires up thru the frame to the relay. Connect the wire with the female blade connector to the relay terminal #30 or #87. Connect the ring terminal to the battery negative (-) terminal
or any 6m bolt on the frame. Turn on the ignition and test the horns. Secure the relay to the frame or other wiring and all loose wires using the cable ties supplied. Replace the seat and side covers

NACA Oil Cooler Inlet Installaiton

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
Locate the -01 and -02 components. Trial fit the two parts making sure the rectangular outlet face is flush. De-burr and trim as necessary. Caution: Care should be exercised when working with fiberglass/epoxy components. epoxy resin and sanding dust can cause an allergic reaction. When epoxying components they must be clean and free of oils and residues. 2.0 Lightly sand the mating surfaces of the two components with #150 grit sandpaper. 3.0 Clamp the two components together and check to insure the outlet face is flush. When the Inlet Assembly is installed the outlet will have the oil cooler attached to it. Therefore, the flange must
34. Oil Cooler Inlet Install Arion Aircraft, LLC Revision 0 1/4/2007 Page 35 – 3 be cut back from the outlet face. Mark the two flanges 1/8 inch from the end. Cut away the two flanges. Smooth the edges where the cuts were made. Page 2 Part Number 160904-01Rev.A 4.0 Pilot drill four holes per side to accept 1/8 inch “pop” rivets (not supplied). These rivets should be located at least 1.5 inches apart and centered on the flange. Final drill holes to size. 5.0 Separate the parts and de-burr the rivet holes. Final inspect the components and clean the mating surfaces with epoxy thinner, lacquer thinner, or Methyl Ethyl Ketone (MEK). 6.0 Mix a small quantity of epoxy (not supplied) and coat both mating surfaces of the components. Mate the two components and install the rivets. Allow Inlet to cure for 24 hours. 7.0 Cut out the center of -03 plate using the 160904-02 template supplied. Trial fit the Oil Cooler Attachment Flange. Once it mates properly and is flush with the -01/-02 assembly, lightly sand the mating surfaces of the two components with #150 grit sandpaper. Also, sand an area completely around the flange extending ½” outward from the cut-out on one face only. Final inspect the components and clean the mating surfaces with epoxy thinner, lacquer thinner, or Methyl Ethyl Ketone (MEK). 8.0 Mix a quantity of epoxy (not supplied) thickened with colloidal silica (not supplied) to a paste consistency and coat both mating surfaces of the components. Mate the two components and create a fillet completely around the flange. Allow Inlet to cure for 24 hours

Kawasaki 2000- ZX-12R Ninja exhaust system Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove the lower fairing. Remove the lower radiator mounting bolts, loosen the upper bolts and pivot the radiator forward to provide access to the exhaust nuts (flange nuts). Remove the oil cooler mounting bolts and pivot the oil cooler forward to provide access. 2. Remove the existing exhaust system and save the flange nuts for reuse. Save the stock exhaust can mounting bolt and nut for reuse as well. 3. Inspect the exhaust gaskets. Replace if necessary. 4. Assemble the head pipes 1, 2, 3, and 4 by matching the joints of the same color to the pair of front Y-pipes. Do not install the exhaust springs at this time. 5. Place a billet aluminum Mouthpiece ring Z on each TiForce head pipe. (see figure 3 for details) . 6. Attach the assembled head pipe sections to the exhaust ports, but do not tighten the flange nuts fully, allowing for some adjustment in the remaining steps. Reuse the flange nuts saved from step 2 above. Make sure the ends of the head pipes fit flush and snug in the ports and Mouthpiece ring Z before tightening. 7. Install the S-Bend to the front section of the head pipes and two Y-pipes. 8. Go back and retighten the head pipe flange nuts per factory specifications – make sure the head pipes and Mouthpiece ring Z are centered in each port. 9. Slide the TiForce end can into place. 10. Loosely attach the two rubber bands, stainless steel bands K, and stay / hanger G to the end can using the supplied 6mm hardware H. (See figure 1) . 11. Place the bands approximately 118 mm from the edge of the end can. (See figure 2) . 12. Using the stock provided mounting point on the passenger foot peg, and using the stock-mounting bolt, mount the end can loosely, allowing for some adjustment. Insert the stock mounting bolt through the stay / hanger G. 13. Attach the supplied springs to all the joints, starting from the head pipes and working back to the end can. 14. Make sure the exhaust system is free and clear, if necessary jiggle the system to adjust for proper clearance