2006 TRIUMPH SPEED TRIPLE ALUMINUM, CARBON FIBER, SLIP-ON EXHAUST SYSTEM INSTALLATION

0

Filed Under (Triumph) by admin on 30-10-2010

download
1) Place the motorcycle in a vise or on it’s stand and make sure it is safe and secure. 2) Remove the right side muffler heat shield. Loosen the right side muffler inlet clamp. Remove and retain the muffler mounting bolt and nut. Remove the right side muffler from the motorcycle. 3) If the gasket remained on the stock muffler inlet tube, remove it and inspect. Replace if necessary and then install onto the Jardine muffler inlet tube. 4) Slide the Jardine muffler into the stock s-bend outlet. 5) Attach the rubber strip to the inside of one supplied muffler clamp. Slide the muffler clamp over the muffler withe the offset facing inward. Squeeze both muffler clamp tabs together and secure it to the muffler mounting bracket using the original bolt and nut. Do not fully tighten yet. 6) Adjust the muffler so it is straight and fully tighten the t-bolt clamp, then the muffler clamp hardware. 7) Repeat steps #2-6 for the left side muffler. 8) Clean all fingerprints from the muffler. Start the motorcycle and check for any exhaust leaks. Ratchet 12mm Socket 12mm Wrench Spring Tool or Needlenose Pliers 2 – Mufflers (Left & Right) 2 – Muffler Clamps 2 – Rubber Strips SLIP-ON EXHAUST SYSTEM TRIUMPH SPEED TRIPLE 2006 18-7008-123-02 ALUMINUM 18-7008-323-02 CARBON FIBER PERFORMANCE DELIVERED! All Jardine products are warranted against defective materials and workmanship for a period of 90 days from date of original consumer purchase. Any non-defective item may be returned within 7 working days, and will be subject to a 20% restocking/repackaging fee. WHATIS WARRANTED: Any Jardine product returned, with prior approval, for defective materials or workmanship including chrome blistering, peeling, bubbling, or any unused (new) Jardine product with rust damage

1999-2001 Triumph Sprint RS Slip-On Exhaust System Installation Instructions

0

Filed Under (Triumph) by admin on 29-10-2010

download
1. Make sure the bike is completely cool before starting the installation. Make sure the bike is secure on the side- stand or ideally a rear service stand. 2. Loosen the clamp that holds the connector pipe to the headers under the bike. Remove the hardware that holds the stock muffler at the passenger footpeg bracket. Take off the muffler. 3. Re-using the stock Triumph clamp install the new S- bend. Leave loose for now. 4. Place a bead of the hi-temp sealant on the outside edge of the s-bend. Slide the TBR canister onto the end of the S-bend pipe. Wipe off the excess sealant that will squeeze out. 5. Carefully slide the muffler clamp over the muffler. ( Note: The stainless steel canister clamp and the name badge on the canister come from the factory with a clear plastic protective film. Please remove this film before operation.) You may need to twist and turn the S-bend a little to get it in the right place. Place the spacer between the stock footpeg bracket and the tabs of the clamp. Locate both tabs of the canister clamp on the outside of the spacer. Use the hardware provided along with the stock nut to secure it. Leave loose for now. 6. Make sure everything is aligned and tighten all hardware. Affix the two connector springs to the muffler. 7. Be sure to allow the sealant to dry per the manufacture’s instructions before starting the bike . Before you run the bike, clean off all fingerprints and dirt, as any oily residue will etch the metal and become somewhat permanent when the system gets hot. Run the bike and enjoy. It is normal for some white smoke to appear the first time you start the bike. This is packing/manufacturing oil from inside the pipe burning off. Check for gaps or leaks. If you find a leak, a little high temperature silicon sealant should fix it. After 50 to 100 miles, recheck all fasteners for tightness.

2006-2010 Triumph Sprint St 1050 Exhaust System Installation Instructions

0

Filed Under (Triumph) by admin on 29-10-2010

download
1. Make sure the bike is completely cool before starting the installation. Make sure the bike is secure on center stand or ideally a service lift. 2. Remove the seat and handle: 3. Remove the rear cowling: 4. Remove the fender assembly: 5. Remove the plastic cover on fender assembly to expose the brake and turn signal wires. Disconnect the brake light wires: 6. Remove the OEM muffler: 7. To install the Two Brothers Racing Slip-on Exhaust System: Attach the slip-tube with the X-Lite Ring™ to the muffler using the 4 (four) 6x14mm socket head cap screws and split lock washers provided. Leave loose for now. 8. Attach the rubber lined muffler clamps and plate brackets as shown to the muffler assembly using the 2 (two) 8x20mm socket head cap screws and nuts provided. Leave loose for now. 9. Install muffler assembly using the OEM mounting bolts and joint clamp. 10. Make sure muffler is aligned when the bike is centered. Then tighten the four V.A.L.E.™ assembly bolts and clamp bolts. Make sure there is clearance between wiring and all body parts. 11. Attach the turn signals/taillights and plate lights as shown in Wiring Diagram. Join wires to main wire harness using the supplied splice connectors and blue scotch locks. You can either cut the OEM modular connectors off of the wiring harness or splice new wire to them. The supplied lighting devices will need to have the modular connectors removed. Run all wiring to the left side of the rear frame, away from the muffler assembly making sure there is adequate clearance from all body parts. Make sure all lights work correctly. 12. Re-install the fender assembly, rear cowling, seat and handle from steps 2-4. 13. Double check your work for alignment and fitment. 14. Before you run the bike, clean off all fingerprints and dirt, as any oily residue will etch the metal and become somewhat permanent when the system gets hot. Remove any plastic film from name badge(s) and/or canister clamp(s). Run the bike and enjoy. It is normal for some white smoke to appear the first time you start the bike. This is packing/manufacturing oil from inside the pipe burning off. Check for gaps or leaks. If you find a leak, a little high temperature silicon sealant should fix it. After 50 to 100 miles, recheck all fasteners for tightness

TRIUMPH STREETTRIPLE 675R AKRAPOVIC SLIP-ON EXHAUST SYSTEM Installation instructions

0

Filed Under (Triumph) by admin on 28-10-2010

download
1. Put the motorcycle on a side stand, we recommend a racing stand. Make sure, that surface is solid and flat. 2. Remove the rider’s seat (Figure 1). Unscrew the bolts and remove the side panels on both side of the motorcycle (Figure 2, 3). T-handle 10mm wrench T-handle 12mm wrench T-handle 13mm wrench T-handle 3mm three hexagon key wrench T-handle 4mm three hexagon key wrench T-handle 5mm three hexagon key wrench Combination 12mm wrench Spring puller Figure 1 Figure 2 Figure 3
NAV – 416 3 3. Unscrew the bolt from the metal clamp at the link pipe – collector joint (Figure 4), the boltfrom the muffler hanging bracket and remove the muffler. Perform the process on both sides of the motorcycle (Figure 5, 6). INSTALLATION OF THE AKRAPOVIC SLIP-ON EXHAUST SYSTEM: 1. Correctly position the carbon-fiber clamps and slide them onto the mufflers as seen in the figures. WARNING: open the clamp slightly wider than the diameter of the outer sleeve of the muffler – do not scrape it along the muffler outer sleeve! (Figure 7, 8, 9). Figure 5 Figure 4 Figure 6 Figure 7 NAV – 416 4 Figure 10 2. Coat the bolts and interior of Akrapovic metal hook clamps with Akrapovic anti-seize lead-free copper paste (black tube) and correctly install them onto the stock collector and hand tighten the bolts (Figure 10, 11, 12, 13). Figure 8 Figure 9 Figure 11 Figure 12 Figure 13 NAV – 416 5 Figure 16 3. Install additional Akrapovic muffler bracket using stock bolts and nuts and tighten them. Perform the process on both sides of the motorcycle (Figure 14, 15, 16)

Vespa GTS 250 exhaust system SERVICE INSTRUCTIONS

0

Filed Under (Vespa) by admin on 28-10-2010

download
to replace the exhaust manifold, order part number 872659 as spare part following standard proceedings. OPERATION PROCEDURE The above picture references the old exhaust flange and the replacement exhaust flange kit part number 872659. Replacement Old
Page 5 of 16 With the complete exhaust system removed from the vehicle remove the lambda sensors. Refer to page 88 and 89 of your Vespa GTS workshop manual for exhaust removal. Loosen the 13 mm bolt to loosen the clamp. Bolt Remove lambda sensor
Page 6 of 16 Remove the header pipe from the exhaust box. Remove the exhaust packing and clamp. Remove exhaust manifold Gasket Clamp Page 7 of 16 Once all packing is removed check and make sure all surfaces are clean. This will help the installation of the exhaust gasket. Install the new clamp supplied with the kit, but do not tighten down at this point. Fit the exhaust gasket onto the new manifold. Push the new exhaust gasket in with the manifold until fitted all the way down to the flange

Vespa GTS250IE/ GTV250IE exhaust system installation Manual

0

Filed Under (Vespa) by admin on 28-10-2010

download
1. Remove the stock Silencer. 2. Put enclosed clamp band to the TiForce tail pipe. Lightly attached the assembled tail pipe to the head pipe. 3. Insert the enclosed TiForce can to the lightly attached tailpipe section. Put the silencer band and rubber to the can. Jiggle the whole assemble for better fitment. Lightly attach the assembled silencer section (see Fig. 1) by enclosed aluminum collar, cap bolt (M8x75mm) and M8 large washer. 4. Make sure the exhaust pipe and silencer are free and clear, if necessary jiggle the system to adjust for proper clearance. 5. Securely fasten the tailpipe section followed by the assembled silencer. 6. Attach enclosed spring to the silencer joint. 7. Using some brake and contact cleaner on a clean rag, carefully wipe down the entire exhaust system to remove any residual oils, anti seize, fingerprints and dirt prior to starting the motor. FAILURE TO CLEAN THE TUBING AND CAN MAY RESULT IN PERMANENT STAINING OF THE SYSTEM WHEN HEATED. 8. Make sure all bolts and nuts are securely fastened. Start the motor and check for exhaust leaks. End

Installation Instructions Fuel Control For BMW Oil heads

0

Filed Under (BMW) by admin on 26-10-2010

download
Removethechrome right air filter cover. Release the brake fluid reservoir from its mount. Follow the oxygen sensor lead from the exhaust to the connector. It is mounted to the back of the brake fluid reservoir mounting bracket with cable ties. Cut the cable ties to release the connector from the bracket. Gently pull the connector apart. Insert the male O2 connector from the R259 into the oxygen sensor lead. Connect the female side of the R259sO2 connector to the bike’swiringharness side. Make sure both sets of connectors are fully seated. Cable tie the sensor lead connector back to the bracket and tuck the other O2 connector under the front of theairhorn. -Depressthe retaining bail on the right fuel injector connector and gently pull off the connector. Install this connector on the male R259 injector lead. Install the remaining R259 connector on the right injector. -Connecttheground lead by removing the allen screw (5mmhex) that secures theairboxtothe frame. Place the screw through the lug on the ground lead and reinstall and tighten the screw. Go to section 3 and verify power-up. Tuck the wiring below and behind theairhornand cable tie as necessary. Using the supplied velcro, attach the controller box to the top of theairhorn. Reinstall the brake fluid reservoir in its mount and reinstall the side-cover. Seethe Techlusionwebsite for more detail. Installation R850, R1100, R1150, R1100S -Refertothe appropriate BMW service guides and remove the fuel tank. On some models it maybe possible to have an assistant lift the tank up and to the left to expose the oxygen sensor connector, without fully disconnecting the tank. Locate the oxygen sensor connector by following the lead from the exhaust system. It will be cable tied to the right frame backbone. Cut the retaining cable ties and pull the connector away from the frame. Open the connector and insert the male R259 O2 connector into the oxygen sensor lead, and the female to the bike’swiringharness. Cable tie these back to the right frame backbone. -Routethe R259 wiring harness down the right frame, in-between the battery tray and the rear fuel tank mount. Using the supplied velcro attach the R259 to theairboxlid. Locate the lead on the right fuel injector, and while depressing the locking bail on the connector, gently pull the leadoff. Install this lead on the R259 male injector connector; install the remaining connector on R259 harness to the right injector. Make sure all of the connectors are fully seated. Cable tie any excess wiring away from the fuel lines and throttle mechanism. -Connecttheground lead to the battery negative terminal or an alternate good ground

BMW F650 GS Single Slipp-On Exhaust System Installation Manual

0

Filed Under (BMW) by admin on 26-10-2010

download
Make sure the bike is completely cool before starting the installation. Make sure the bike is secure on the side- stand or ideally a rear service stand. 2. Remove the stock exhaust canisters. 3. Install the 90obracket on the left side of the bike per the photo. Reuse the stock torx bolt to secure. 4. Place a bead of the hi-temp sealant on the outside edge of the header that goes into the S-bend. Slide the barrel clamp onto the end of the s-bend (the end with the slots cut into it). Slide the S-bend and barrel clamp onto the end of the header. Wipe off the excess sealant that will squeeze out. 5. Place a bead of the hi-temp sealant on the outside edge of the s-bend that goes into the canister. Slide the TBR canister onto the end of the S-bend pipe. Wipe off the excess sealant that will squeeze out. 6. Carefully slide the muffler clamp over the muffler. ( Note: The stainless steel canister clamp and the name badge on the canister come from the factory with a clear plastic protective film. Please remove this film before operation.) You may need to twist and turn the S-bend a little to get it in the right place. Locate both tabs of the canister clamp outside of the 90obracket. Use the 8mm x 20mm flange bolt and 8mm nut &washer to secure it. Leave loose for now. 7. Make sure everything is aligned and tighten all hardware. Affix the connector springs to the muffler. 8. Before you run the bike, clean off all fingerprints and dirt, as any oily residue will etch the metal and become somewhat permanent when the system gets hot. Run the bike and enjoy. It is normal for some white smoke to appear the first time you start the bike. This is packing/manufacturing oil from inside the pipe burning off. Check for gaps or leaks. If you find a leak, a little high temperature silicon sealant should fix it. After 50 to 100 miles, recheck all fasteners for tightness

BMW R1200GS Exhaust System Installation instructions

0

Filed Under (BMW) by admin on 26-10-2010

download
The manufacturer, importer or dealer shall not be liable for any incidental damage including personal injury or any other damages caused by improper installation or operation of the Akrapovič exhaust system. When installing the Akrapovič exhaust system be careful that the exhaust system does not touch other parts sensitive to high temperature. 2. Akrapovič makes no representation or warranties with regard to damage caused by the improper installation, use and maintenance of the Akrapovič exhaust system. The warranty is limited to defects recognized by our technical department and due to normal use, and excludes items subject to normal wear (gaskets and damping wool). The guarantee is void in case of accident, modification, improper or competition use. 3. Do not attempt to install the Akrapovič exhaust system on a vehicle model for which it was not made or tested by Akrapovič. 4. When the exhaust system gets very hot during operation, be careful not to burn yourself on the exhaust system or parts which are in direct contact with it, even when the engine is not running. Also protect other people, especially children, from the injuries mentioned above. 5. In some cases Akrapovič exhaust system kits contain chemical products (ceramic anti-seizing grease; bolt sealant). Handle with care, do not inhale or swallow. Avoid excessive contact with skin, eyes or mucous membranes. Keep out of reach of children. 6. Technical specifications of Akrapovič exhaust systems and related products are subject to change without notice. 7. Before removing the original exhaust system from your vehicle, please compare the parts you received with the list of materials provided in the installation manual in order to assure that you have all the parts necessary for the installation of your new Akrapovič exhaust system. 8. Although this manual consists of instructions for installation in written form, as well as photographs and pictures representing individual steps of the installation, please note that the photographs and pictures are symbolic and are intended for representation of general overview only. The photographs and pictures contained herein should serve as a guideline only and actual installation of the exhaust system may not correspond with the photographs and pictures entirely.

BMW K1200 RS/ GT Full Exhaust System Full Exhaust System Installation Manual

0

Filed Under (BMW) by admin on 26-10-2010

download
1. Make sure the bike is completely cool before starting the installation. Make sure the bike is secure on the side- stand or ideally a rear service stand. 2. Remove the lower fairing. 3. Unscrew the O 2 sensor. Remove the stock exhaust system at the rear canister support bracket and where it bolts to the engine. CAUTION -the stock exhaust is very heavy, be careful not to drop it! Also, be careful not to damage the engine sensor located near the front header pipe. 4. Pry out the old exhaust port gaskets and replace with new BMW OE (x4) exhaust port gaskets. Adab of grease will help hold the gaskets in place while you work. 5. Coat the exhaust studs and O 2 sensor threads with high temperature anti-seize compound. 6. Install the TBR headers into the exhaust ports making sure to get a good seat onto the exhaust port gaskets. Next, install the header nuts starting at the rear/outside stud and working your way forward on the outside set of studs. Once that is finished repeat along the inside set of studs. Tighten header nuts only finger tight at this point. 7. Be sure to coat the threads of the sensor with the included packet of hi-temp anti-seize. Install the O 2 sensor into the TBR headers. Turning the sensor in the counterclockwise direction a few times then screwing it clockwise to install will help make it easier to install and prevent the wire from binding. 8. Place a bead of the hi-temp sealant on the outside edge of the headers that goes into the canister. Slide the TBR canister onto the end of the S-bend pipe. Wipe off the excess sealant that will squeeze out. 9. Carefully slide the muffler clamp over the muffler. ( Note: The stainless steel canister clamp and the name badge on the canister come from the factory with a clear plastic protective film. Please remove this film before operation.) Attach it to the canister support bracket using the stock BMWhardware. Both tabs of the canister clamp should be located on the inside of the canister support bracket. Leave loose for the moment. 10. Make sure everything is lined up and start to evenly tighten up the header nuts to BMWfactory torque specification. Tighten the canister support hardware and install the springs as well. 11. Start the bike and check for leaks around the exhaust ports and the header/canister junction. 12. Reinstall the lower fairing