HARLEY-DAVIDSON SOFTAIL CROSSOVER REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-04-2012

download
EXHAUST SYSTEM REMOVAL READ ALL INSTRUCTIONS BEFORE BEGINNING 1. Under the oil tank on the right hand side, locate the rear O² sensor connector. Unplug sensor and feed the end of wire through the frame freeing it from motorcycle. NOTE: Pay attention to wire routing for re-installation. 2. Open the plastic cover above the rectifier on front of the frame to access to the front O² sensor connector. Unplug sensor from harness. Remove ZIPSTRIP holding wire to frame and feed the wire through freeing it from motorcycle. 3. On floorboard equipped models, loosen the right hand floorboard mounting bolts to gain clearance for exhaust removal and installation. 4. Loosen the heat shield clamps on both front and rear exhaust pipes. 5. Remove the mounting nuts from each head pipe, located at the cylinder head. 6. Remove the nuts attaching the exhaust mount bracket to the frame. 7. On FLSTD and FLSTF models, you will need to remove the right side passenger foot peg and hanger, as this is attached to the exhaust mount bracket. Replace the passenger foot peg assembly using the BOLT 14 Allen bolt (supplied). 8. Remove the entire exhaust system and set it aside. 9. Remove the two lower mounting studs from the frame See figure 1 . Recommended replacement exhaust port gaskets, H-D P/N: 65324-83A. 10. Carefully remove exhaust port flanges and circlips from the stock exhaust system using snapring pliers. See figure 2 . NOTE: Replace bent or damaged circlips. Check exhaust port gasket condition. 11. Remove O² sensors from stock head pipe and set aside for re-installation on your new RUSH exhaust system. PAGE 1 OF 4 RUSH RACING PRODUCTS EXHAUST SYSTEM INSTALLATION P/N 7020 – 7120 BEFORE INSTALLATION PLEASE READ ALL INSTRUCTIONS 1. Remove header and heat shields from protective packaging. Place each heat shield on a non-abrasive surface such as a blanket or carpet. Using a felt tip pen, mark outside edge of each heat shield to show location of mounting clips that hose clamps will loop through See figure 3. 2. Apply a small amount of anti-seize compound to the threads of the O² sensors and install them into the new head pipe. NOTE: Be careful not to get anti-seize on sensor tip, it may affect sensor function. 3. Install circlips and flanges from stock system onto the new head pipe See Figure 2. Note: Replace circlips if bent or damaged 4. Attach BRKT-007 to frame using two BOLT 12 Tighten to factory specs. 5. Install complete assembly into exhaust ports (rear port first). Use stock flange nuts, Do Not Tighten .

HARLEY-DAVIDSON SPORTSTER SHORTSHOTS STAGGERED INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-03-2012

download
1. Find and unplug the O2 sensor wires from the wiring harness and remove nylon cable tie holding front wire to frame. Feed the end of the wires through the frame so they are free from the motorcycle. NOTE: Pay attention to wire routing for re-installation. 2. Loosen the heat shield clamps on both the front and rear exhaust pipes. This allows easier access to the head pipe mounting nuts. 3. Remove the two head pipe mounting nuts from each fl ange, located at the cylinder head. 4. Remove the clamp bolt which mounts the rear head pipe to the belt drive cover bracket. 5. Remove the two bolts from each muffl er body where they attach to the mounting bar. Carefully remove exhaust pipes from the motorcycle and set aside. 6. Using a 7/8″ or 22mm wrench, carefully remove the O2 sensors from the stock head pipes and save for re-use with the new system. 7. Remove the drive belt cover and take the bracket off the rear cover bolt, the bracket will not be re-used. 8. Loosen the brake rod at the rear eyelet using a T30 torx driver. 9. Remove the three mount bolts and washers attaching the exhaust mounting bar (save hardware for re-use). 10. Carefully remove exhaust port fl anges and circlips from the stock exhaust system using snapring pliers. NOTE: Replace bent or damaged circlips. Check exhaust port gasket condition

HARLEY-DAVIDSON SOFTAIL STRAIGHTSHOTS 2-2 INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-03-2012

download
1. Under the oil tank on the right hand side, locate the rear O2 sensor connector. Unplug sensor and feed the end of wire through the frame freeing it from motorcycle. NOTE: Pay attention to wire routing for re-installation. 2. Open the plastic cover above the rectifi er on front of the frame to gain access to the front O2 sensor connector. Unplug sensor from harness. Remove cable tie holding wire to frame and feed the end of the wire through, freeing it from motorcycle. 3. On FLSTC, FLSTF, FLSTN and FLSTSC models, loosen the right hand fl oor board mounting bolts to gain clearance for exhaust removal and installation. 4. Loosen the heat shield clamps on both front and rear exhaust pipes. 5. Remove the two mounting nuts from each head pipe, located at the cylinder head. 6. Remove the nuts attaching the exhaust mount bracket to the frame. 7. On FLSTN, FLSTF and FXSTD models, you will need to remove the right side passenger footpeg and hanger, as this is attached to the exhaust mount bracket. Remove hanger, and replace the passenger foot peg assembly using the 3/8″ x 2 1/2″ Allen bolt (supplied). 8. If equipped, unbolt the carriage bolt and clamp attached to the bracket under the right side transmission cover. 9. Remove the entire exhaust system and set it aside. 10. If equipped, remove the bracket from under the right side transmission cover. 11. Using a 7/8″ or 22mm wrench, carefully remove the O2 sensors from the stock head pipes and save for re-use with the new system. 12. Remove the two lower mounting studs from the frame (Figure 1). 13. Carefully remove exhaust port fl anges and circlips from the stock exhaust system using snapring pliers. NOTE: Replace bent or damaged circlips. Check exhaust port gasket condition. Recommended replacement exhaust port gaskets, Harley part number:17048-98 or 65324-83A

HARLEY-DAVIDSON DRESSER BIG SHOT DUALS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 18-03-2012

download
1. Remove both left and right saddlebags and set them aside. 2. Loosen the bolt from the pinch clamp on the front end of each muffl er. Note: On older model Dressers, spread the clamps just enough to remove them. 3. Remove the two 5/16″ bolts that mount the muffl er to the saddlebag supports. Repeat this step on the opposite muffl er. 4. Remove the stock muffl ers with sliding hangers and set them aside. Note: It may be necessary to use a penetrating lubricant to loosen the muffl er from the head pipe. 5. Remove the right hand fl oor board. 6. Remove both passenger fl oor boards. 7. Loosen the heat shield clamps on both front and rear exhaust pipes. 8. Loosen the rear head pipe clamp located behind the rear cylinder. Remove the section of head pipe connecting the left side muffl er. 9. Remove the clamp holding the front head pipe to the transmission housing. 10. Remove the two mounting nuts from each head pipe, located at the cylinder head. Carefully remove the head pipes and set them aside. 11. Remove the rear cylinder bracket by removing the two starter mounting bolts. Install new mounting bracket (stamped 353-P), and torque to (13-16) ft. lbs. (Figure 1). Make sure the battery ground cable is secure and properly routed. Install mounting post (from stock system) so the nut is accessible from right side of motorcycle and saddle will support underside of exhaust pipe. Note: Pre 1998 dressers do not come with this mounting post. It can be ordered from your local dealer, Harley part number: 65619-98. 12. Carefully remove the exhaust port fl anges and circlips from the stock exhaust system using snapring pliers. Note: If circlips look bent or twisted replace them

HARLEY-DAVIDSON SPORTSTER SHORTSHOTS STAGGERED BLACK INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 17-03-2012

download
1. Find and unplug the O2 sensor wires from the wiring harness and remove nylon cable tie holding front wire to frame. Feed the end of the wires through the frame so they are free from the motorcycle. NOTE: Pay attention to wire routing for re-installation. 2. Loosen the heat shield clamps on both the front and rear exhaust pipes. This allows easier access to the head pipe mounting nuts. 3. Remove the two head pipe mounting nuts from each fl ange, located at the cylinder head. 4. Remove the clamp bolt which mounts the rear head pipe to the belt drive cover bracket. 5. Remove the two bolts from each muffl er body where they attach to the mounting bar. Carefully remove exhaust pipes from the motorcycle and set aside. 6. Using a 7/8″ or 22mm wrench, carefully remove the O2 sensors from the stock head pipes and save for re-use with the new system. 7. Remove the drive belt cover and take the bracket off the rear cover bolt, the bracket will not be re-used. 8. Loosen the brake rod at the rear eyelet using a T30 torx driver. 9. Remove the three mount bolts and washers attaching the exhaust mounting bar (save hardware for re-use). 10. Carefully remove exhaust port fl anges and circlips from the stock exhaust system using snapring pliers. NOTE: Replace bent or damaged circlips. Check exhaust port gasket condition. Recommended replacement exhaust port gaskets, Harley part number:17048-98 or 65324-83A.

YAMAHA V-STAR 650 CA SHORTSHOTS STAGGERED INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 29-12-2011

download
Check condition of stock exhaust gasket. Replace if damaged or worn. 2. Install mounting bracket (stamped 384-P) in the original bracket mounting position using two 8mm bolts (supplied)(Figure 1). Note: Install two 5/16″ x 5/8″ fl ange bolts (supplied)(Figure 1) into top holes of bracket before installing bracket onto motorcycle. 3. Mark outside surface of front and rear heat shields with location of mounting clips that are welded to the inside (Figure 2). Place each heat shield on a non abrasive surface such as a blanket or carpet. Lay each head pipe/muffl er onto its respective heat shield (Figure 3). 4. Loosely install each hose clamp by feeding tail end of clamp into heat shield clip (Figure 2). #20 hose clamps are for head pipes and #28 hose clamps for muffl er area. Take note of clamp screw head direction (Figure 4). Screw head should be accessible when system is installed on motorcycle for adjustment purposes. Note: Do not tighten yet. 5. Install 6″ fl ange bolts (supplied) engaging nut plate. Leave T-bolt clamp onto front muffl er (Figure 4&5). Slide muffl er onto front head pipe. Slide nut plate (supplied) inside bracket welded to backside of front muffl er (Figure 6). Attach muffl er to mounting bracket 384-P using two 5/1head pipe/muffl er assembly loose at this time. 6. Using stock Allen bolts, carefully install rear head pipe/ muffl er assembly into exhaust port. (Assistance may be required). Note: Do not tighten yet. 7. Slide nut plate (supplied) inside bracket welded to backside of rear muffl er (Figure 6). 8. Align muffl ers so they are parallel when viewed from the right side of the motorcycle and muffl er tips align at the same length. Tighten 5/16″ fl ange bolts securing muffl ers to bracket. 9. Tighten cylinder exhaust port bolts securing head pipes to cylinder head. 10. Tighten T-bolt clamp securing front muffl er to head pipe. 11. Adjust heat shields so that muffl er tips protrude 1/4″ from heat shields (Figure 7) and rotation of heat shield matches muffl er tip. Tighten all hose clamps securing heat shields. 12. After installation and before starting motorcycle, completely clean pipes and muffl ers with cleaning solvent and a clean, soft cloth that will not leave a residue. Note: Any residue, oil, or fi ngerprints will stain the chrome when the metal heats up. 13. All hardware must be properly tightened before starting motorcycle

HONDA AERO 750 CRUZER EXHAUST SYSTEM REMOVAL And INSTALLATION

0

Filed Under (Honda) by admin on 18-11-2011

download
Install mounting bracket (stamped 363-P) in the original muffler mounting position, using two 10mm bolts and
one 10mm nut. (supplied)(Refer to figure 2). 2. Mark outside surface of front and rear heat shields with location of mounting clips that are welded to the inside.(Refer to figure 3).Place each heat shield on a non-abrasive surface such as a blanket or carpet. Position each head pipe/muffler over its respective heat shield. (Refer to figure 4).
3. Feed tail end of each hose clamp through each mounting clip welded to back side of front and rear heat shields. Take note of clamp hex screw head direction. (Clamp head direction is critical for adjustment when system is installed on bike.) Wrap each clamp around back side of head pipe threading tail end into clamp head. (Refer to figure 3 & 4).
4. Install front head pipe/muffler using stock flange nuts. Slide dog bone shaped nutplate (supplied) inside
bracket welded to backside of muffler. Attach muffler to mounting bracket 363-P using (supplied) 5/16” flange
bolts engaging dog bone nutplate. Leave head pipe/muffler assembly loose at this time (Refer to figure 4). Repeat this step with the rear head pipe.5. Align mufflers so they are parallel when viewing from right side of the motorcycle. Tighten 5/16” flange bolts securing upper and lower muffler positions.. Tighten cylinder exhaust port flange nuts securing head pipes to cylinder heads. 7. Adjust heat shields so they meet front of muffler taper. (Refer to figure 6). Tighten all hose clamps securing heat shield locations. NOTE: Heat shields should cover muffler/head pipe weld joint.

SUZUKI SV1000S EMISSION CONTROL INFORMATION/ SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
EMISSION CONTROL SYSTEMS FUEL INJECTION SYSTEM SV1000S motorcycles are equipped with a fuel injection system for emission level control. This fuel injection system is precision designed, manufactured and adjusted to comply with the applicable emission limits. BEFORE-PRESSURIZED FUEL PRESSURIZED FUEL * I’ RELIEVED FUEL ~%~~~ Ift 0 0 9 0 0 0 EMISSION CONTROL INFORMATION 9-3 CRANKCASE EMISSION CONTROL SYSTEM The engine is equipped with a PCV system . Blow-by gas in the engine is constantly drawn into the crankcase, which is returned to the combustion chamber through the breather hose, air cleaner and throttle body . C * FRESH AIR FUEL/AIR MIXTURE 411111110 BLOW-BY GAS 9-4 EMISSION CONTROL INFORMATION EXHAUST EMISSION CONTROL SYSTEM (PAIR SYSTEM) The exhaust emission control system is composed of the PAIR system and THREE-WAY CATALYST system. The fresh air is drawn into the exhaust port with the PAIR solenoid valve and PAIR reed valve . The PAIR solenoid valve is operated by the ECM, and the fresh air flow is controlled according to the TPS, ECTS, IATS, ZAPS and CKPS. H02 sensor (Except for USA) I 0 0 0 0 0 NOISE EMISSION CONTROL SYSTEM TAMPERING WITH THE NOISE CONTROL SYSTEM PROHIBITED : Federal law prohibits the following acts or the causing thereof: 1. The removal or rendering inoperative by any person, other than for purposes of maintenance, repair or replacement, of any device or element of design incorporated into any new vehicle for the purpose of noise control prior to its sale or delivery to the ultimate purchaser or while it is in use, or 2. The use of the vehicle after such device or element of design has been removed or rendered inoperative by any person. AMONG THOSE ACTS PRESUMED TO CONSTITUTE TAMPERING ARE THE ACTS LISTED BELOW : • * Removing or puncturing the muffler, baffles, header pipes, screen type spark arrester (if equipped) or any other component which conducts exhaust gases . • * Removing or puncturing the air cleaner case, air cleaner cover, baffles or any other component which conducts intake air . • * Replacing the exhaust system or muffler with a system or muffler not marked with the same model specific code as the code listed on the Motorcycle Noise Emission Control Information label . EVAPORATIVE EMISSION CONTROL SYSTEM (FOR E-33)

YAMAHA V-STAR 650 CRUZER EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 28-12-2010

download
STOCK EXHAUST SYSTEM REMOVAL 1. This Exhaust system is specifically designed for California models, before continuing be sure it is the correct system for your application. 2. Loosen clamp that connects muffler to front head pipe. 3. Remove cylinder exhaust bolts from rear head pipe that connects rear head pipe to cylinder (save for re- use). 4. Remove bolts that connect mufflers to mounting bracket. Remove complete system. Note: Assistance may be required. Page 1of 4 Y411IN Rev. 1.0 YAMAHA V-STAR 650 CRUZER EXHAUST SYSTEM, CA Model Part #31505 Tools required for installation: 1/2”, 12mm & 10mm wrenches 5mm, 6mm Allen wrenches 5/16″ nutdriver / flat blade screwdriver VANCE & HINES EXHAUST SYSTEM INSTALLATION 1. Check condition of stock exhaust gaskets. Replace if damaged or worn. 2. Install mounting bracket (stamped 370-P) in the original muffler mounting position, using two 8mm bolts (supplied)(Figure 1). 3. Mark outside surface of front and rear heat shields with location of mounting clips that are welded to the inside (Figure 2). Place each heat shield on a non abrasive surface such as a blanket or carpet. Lay each head pipe/muffler onto its respective heat shield (Figure 3). 4. Loosely install each hose clamp by feeding tail end of clamp into heat shield clip (Figure 4). Take note of clamp screw head direction (Figure 3). Screw head should be accessible when system is installed on motorcycle for adjustment purposes. Note: Do not tighten yet. 5. Install T-bolt clamp onto front muffler. Slide muffler onto front head pipe. Slide dog bone shaped nut plate (supplied) inside bracket welded to backside of front muffler. Attach muffler to mounting bracket 370-P using two 5/16″ flange bolts (supplied) engaging dog bone nut plate. Leave head pipe/muffler assembly loose at this time (Figure 4). 6. Using stock Allen bolts, carefully install rear head pipe/muffler assembly into exhaust port. (Assistance may be required). Note: Do not tighten yet. 7. Slide dog bone shaped nut plate (supplied) inside bracket welded to backside of rear muffler

HONDA VT750 EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Honda) by admin on 24-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Remove the header flange nuts at the exhaust port on the front and rear head pipes. 2. Remove the two 8mm nuts from the muffler mounting bracket, while supporting the entire exhaust system. Lower the system down and set it aside. Note: Save the stock hardware for reuse. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Check the stock exhaust gaskets to be sure they are in good shape. If you have any doubts as to their condition, replace them. 2. Install the muffler mounting bracket (stamped 268) to the original muffler mounting point, using the two stock 8mm nuts. Refer to figure 1. 3. Slide one dog bone shaped nut plate under the bracket that is welded to the backside of the front muffler. 4. Install the front head pipe to the cylinder head using the stock nuts. Attach the muffler to the mounting bracket using the two 5/16″ flange bolts (supplied). Leave the nuts and bolts loose at this time. 5. Repeat steps 2 and 3 with the rear header. 6. Align the mufflers so they are parallel when viewing from the right hand side of the motorcycle. Tighten all the hardware evenly. 7. Unscrew all of the hose clamps (supplied) until they are completely loose. Mark the top edge of both heat shields with the location of the mounting clips that are welded to the backside. Position the front heat shield over the head pipe and feed the tail end of the hose clamps into the clips. Be sure that each hose clamp is engaged with both clips. Repeat this step with the rear heat shield. 8. Rotate the hose clamps on both heat shields so they are accessible with a screw driver and tighten each of them evenly. The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. Note : The heat shields should cover the weld on the muffler. 9. Be sure to remove any dirt, oil or finger prints from the entire exhaust system before starting the motorcycle.