Kawasaki ZX-14 TITANIUM SIDEWINDER EXHAUST Installation Instructions

0

Filed Under (Kawasaki) by admin on 30-04-2012

download
STEP 2: PRE-ASSEMBLE HEADERS, COLLECTOR, AND MID-PIPE TO INSURE PROPER FIT BETWEEN ALL PARTS: Brock’s Performance pre-assembles the exhaust system before it is shipped to your door. We ask you to this to insure there were no shipping damages incurred before you start disassembling your bike. A lot of our customers use WD-40 applied to the joints to ease assembly, adjustment, and/or disassembly. STEP 3: REMOVE ZX-14 RIGHT AND LEFT DASHBOARDS : The right and left dashboards are held in place by three fasteners (Figure 4) which are removed with a No. 4 hex head wrench. Note that all dashboard and fairing fasteners have thin plastic washers located between the fastener head and the plastic body work. Be careful to save the plastic washers. To avoid losing fasteners and washers it is recommended that the installer place them in a container once they are removed. STEP 4: REMOVE ZX-14 LOWER FAIRING : The lower fairing consists of separate right and left side panels, both of which should be removed. The locations of the bolts and plastic push pins holding the fairing in place are illustrated in Figure 5. Details are provided below. • The plastic push pins is located in the front of the fairing (3) , aft of the front tire, and holds the left and right panels together. Remove the plastic push pins using a thin blade screw driver to lift the rivet head. Then pull the rivet from the bodywork. This will release the right panel from the left panel. • Remove the lower fairing fasteners & washers (1 & 2) on the right fairing panel with a No. 5 hex head wrench. • Remove the upper fairing fasteners & washers (4, 5, & 6) on the right fairing panel with a No. 4 hex head wrench. • Note that the top of the fairing incorporates slots into which hooks at the bottom of the mid fairing (red bodywork) fit. These hooks are shown in Figure 8. Pull the bottom of the lower fairing panel away from the bike and then downward to clear the hooks from the slots. The right side lower fairing should now separate easily from the mid-fairing. • Repeat for the left side lower fairing

Yamaha V-Star 1100 Jetting the Carburetors INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 11-03-2012

download
Remove air filter housing Remove the seat or seats Disconnect Fuel Lines (also the vapor line from tank to charcoal canister on California models) Disconnect instrument connectors from the fuel tank Remove fuel tank Remove air box Disconnect TPS and heater connectors Remove chrome carb cover Disconnect Fuel Lines Remove rubber carb elbows Disconnect throttle cables from carbs Remove the carbs Perform the jetting 1. Remove the Chrome air filter housing. To remove the chrome dog-dish (air filter housing) from the right side of the bike, you will need to remove the two mounting bolts and loosen the clamp that holds the air duct to the back of the housing. You will need a 5 mm Allen wrench and a #2 Philips screwdriver. 2. Remove the seats. This can be accomplished by using a 5 mm Allen wrench and removing the Allen head bolt from just behind the rear seat and the bolt just behind the front seat. Pulling up and back will free the seats. One smooth motion will do it. 3. Gain access to the dashboard plug and unplug it (It is white) Note: Your trip odometer will lose its count, please record the number if you wish to save your current mileage for this tank of gas. Figure A shows the three plastic rivets that need to be removed to gain access to the dashboard plug. Using your Philips head screwdriver, press the small circle in the middle of the rivets down… a click is felt. Remove the rivets by hand. You have freed the cover and you may lift it up to expose the electrical connector that needs to be unplugged. Figure B shows the plug

Toyota Avensis Equipment REMOVAL AND INSTALLATION

0

Filed Under (Toyota Manuals) by admin on 05-10-2011

Trip computer with fuel consumption &average speed display (where standard audio fitted) Outside temperature display Instrument display dimmer Digital odometer with two trip meters Digital Clock Dashboard integrated multi-information display (where standard audio fitted) Fuel Caplocation indicator Rearfoglamps indicator Sequential automatic transmission mode indicator (where sequential automatic fitted) Tachometer Fuel indicator with low fuel warning Water temperature indicator Engine temperature warning Engine management warning Lights Onwarning Door Ajarwarning



Ducati GPS RECEIVER Installation and instruction manual

0

Filed Under (Ducati) by admin on 26-10-2010

download
When supplied, the receiver will start searching for visible satellites. During this phase, the RED LED light is fixedly on. After having identified an adequate number of satellites, the LED will slowly blink. Now, you can enter the coordinates of the finish line simply by pressing the button near the LED when you are crossing the finish line of the track. This operation can be performed both at a halt and when moving. If performed when moving, the system will also acquire the direction of running and it will avoid detecting a false finish line on very narrow tracks (typically Kart or Motocross tracks) where there is a counter straight stretch close to the main straight stretch, but opposite to it. Setup can be also performed at a halt on normal speed tracks. When the finish line is acquired, the LED is blinking quickly. This means that the finish line is within a reach of 5 km. The GPS Receiver will store the finish line coordinates last used even if disconnected. It is necessary to set up a new finish line only when you change the track. Attention: when you restart after having moved a lot of kilometres, the receiver may even take some minutes (5-6) to acquire the satellites and let the LED blink. At the power on, it is always recommended to place the vehicle in an open area where it has got the sky visibility necessary to acquire the GPS signal as quickly as possible. Note: In order to display the acquired Laptimes you must activate the Lap functions on the original dashboard by following the Ducati handbook indications. LED operation RED LED ON FIXED: Receiver searching for satellites RED LED SLOW BLINKING: Satellites properly acquired, press the button on the finish line to set up the end-of-lap. RED LED QUICK BLINKING: Satellites on sight and finish line within a reach of 5Km, the system can detect the crossing of the finish line you have setup.

Ducati 1098 and 1098S ECU connection Installation Manual

0

Filed Under (Ducati) by admin on 25-10-2010

download
ECU can be connected to AIM loggers in two different ways: directly, or using the connector placed on the dashboard. 2.1. – Direct connection between AIM loggers and Marelli IAW 5AM2 ECU IAW 5AM2 is equipped with two 38 pins connectors, named “Body ” and “Engine” – see below: “engine” is black (on the left). “Body” connector is grey (on the right). To connect AIM loggers to Ducati ECU: • connect AIM cable labelled CAN+ to pin 20 of “Body” connector. • connect AIM cable labelled CAN- to pin 29 of “Body” connector. • Vbatt is on pin 17 (vehicle master switch). 2.2 – Dashboard connector Connector is equipped with 26 pins and it is placed on the back of the dashboard. To connect AIM loggers to ECU using the dashboard connector: • connect AIM cable labelled CAN+ to pin 19 (green/black twisted cable) connector. • connect AIM cable labelled CAN – to pin 26 (grey/green twisted cable) connector. • Vbatt is on pin 23 – red /black cable – vehicle master switch. Warning: to use Marelli dashboard , please remove 120 OHM resistance placed between CAN+ and CAN-; otherwise Marelli dash does not work