2002 Kawasaki 360 ATV WINCH ACCESSORY INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 08-05-2012

download
1. Remove the two 8mm bolts that attach the front bumper assembly to the ATV frame see figure 3. 2. Place Winch mounting plate (A1) into position and fasten the two bent down tabs to the ATV frame using the two 8mm bolts removed in step one, see figure 4, and figure 5. Do not tighten fully at this time. 3. Attach the front of the mounting plate using four 1/4-20 u- bolts (B1), eight lock washers (B2), and eight 1/4-20 hex nuts (B3), see figure 6. 4. Tighten all fastners for the mounting kit at this time. 5. Place winch into position behind the mounting plate. Attach the top two feet of the winch using two 5/16-18 hex cap screws and lock washer. These fasteners will be found in the hardware kit that came with the winch. Note: The winch has floating nuts in its feet. In some instances, a nut may be moved off to one side making it impossible to screw a bolt in. If this becomes the case, take a screwdriver and center the floating nut in the winch to the bolt hole opening. Now attach the bolt through the Winch Plate and into the winch. 6. If using a Cast Hawse Fairlead: It may be neccasary to remove the cast hawse fairlead from the fairlead mounting plate that came with the winch.

2009 Harley Davidson Softail POWER COMMANDER V INPUT ACCESSORY INSTALLATION

0

Filed Under (Harley Davidson) by admin on 26-02-2012

download
1 Remove the seat 2 Uplug the stock wiring harness from the ECM (Fig. A) 3 Remove the 4 nuts that hold the ECM to the bracket and remove the ECM. 4 Remove the bolt that holds the seat strap to the rear fender. 5 Remove the ECM bracket from the fender. Remove one nut at a time or the bracket will fall into the tire. Reinstall the nuts to support the inner fender bracket. Due to the limited amount of room on this bike the seat strap and ECM bracket can NOTbe re-used. 6 Connect the PCVharness in-line of the stock wiring harness and ECM (Fig. B). 7 Place the BLACK PCVto GREYstock connector as close to the fuse box as possible. This connection will NOT lay flat against the frame. 8 Using the supplied velcro secure the ECM to the rear fender. Place the ECM as far down as possible. The upper part of the ECM will just overlap the bolt hole for the seat strap. Make sure to clean both surfaces with the alcohol swab before attaching. If using the Autotune kit offset the ECM about 1″ from center to the right side of the bike. 9 Remove the security module from the top of the battery (Fig. C). This unit slides to the right of the bike.

TOYOTA TACOMA 2008 – INTERFACE KIT FOR IPOD REPAIR

0

Filed Under (Toyota Manuals) by admin on 01-11-2011

download
Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation. These guidelines can be found in the “Accessory Installation Practices” document. This document covers such items as: • Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.). • Safety (eye protection, rechecking torque procedure, etc.). • Vehicle Disassembly/Reassembly (panel removal, part storage, etc.). • Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.). Please see your Toyota dealer for a copy of this document. 1. Vehicle Protection. (a) Place driver seat in mid position. (b) Set emergency brake. (c) Remove the negative battery cable. (Fig. 1-1) (1) Protect the fender before starting. CAUTION: Do not touch the positive terminal with any tool when removing cable. (d) Using protective blankets cover front seats, interior of vehicle and center console and front side of the shift lever. (e) Wait 90 seconds before proceeding to disassemble vehicle. 2. Disassembly of Vehicle. NOTE: Place all removed parts on a protected surface. NOTE: When disconnecting wiring connectors, do not pull on the wiring; pull on the connector only. (a) Remove air conditioning control assembly (L,R). (Fig. 2-1) (1) Apply protective tape. (2) Using a panel remover, disengage the four (4) clips and remove the air conditioning control assembly

2005-2010 TACOMA RUNNING BOARD REPAIR

0

Filed Under (Toyota Manuals) by admin on 31-10-2011

download
Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation. These guidelines can be found in the “Accessory Installation Practices” document. This document covers such items as:- — Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.). — Safety (eye protection, rechecking torque procedure, etc.). — Vehicle Disassembly/Reassembly (panel removal, part storage, etc.). — Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.). Please see your Toyota dealer for a copy of this document. 1. Remove Running Board from Packaging. (a) Remove running board assembly from package and place on a clean protected surface. The boards are sided (Fig. 1-1) (b) Verify kit contents and inspect the running board for damage. 2. Running Board Preparation for Installation (LH/RH Side). (a) Verify hardware bag content by referring to the cover page of this instruction sheet. (b) Loosen the 1/4 – 20 flange nuts at each of the three (3) bracket locations on each running board. (Fig. 2-1) (c) With a small slotted screwdriver, remove the plastic plugs covering M8 weld nuts in body of vehicle at 6 points/side.

2005-2010 TACOMA CARGO DIVIDER Preparation and Bracket Installation

0

Filed Under (Toyota Manuals) by admin on 27-10-2011

download
Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation. These guidelines can be found in the “Accessory Installation Practices” document. This document covers such items as:- — Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.). — Safety (eye protection, rechecking torque procedure, etc.). — Vehicle Disassembly/Reassembly (panel removal, part storage, etc.). — Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.). Please see your Toyota dealer for a copy of this document. 1. Bracket Installation (a) Remove end caps from the back of each vehicle bed side rail. (Fig. 1-1) (b) Slide one clamp plate into each side rail. (Fig. 1-2) (c) Install the LH Bracket (with the WARNING label) onto the LH clamp plate threaded stud

TOYOTA TACOMA 2005 D RING CARGO TIE DOWN Procedure

0

Filed Under (Toyota Manuals) by admin on 14-10-2011

download
Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation. These guidelines can be found in the “Accessory Installation Practices” document. This document covers such items as:- — Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.). — Safety (eye protection, rechecking torque procedure, etc.). — Vehicle Disassembly/Reassembly (panel removal, part storage, etc.). — Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.). Please see your Toyota dealer for a copy of this document. 1. Hole Placement – Left Side (a) Measure vertically 70 mm up from bottom of truck bed, using marking pencil draw a small horizontal line. (Fig. 1-1) (b) Horizontally measure 72 mm from the front of truck bed, using marking pencil draw a vertical line. (Fig. 1-1) (c) Set drill stop at 1″ from drill tip. (d) Use a center punch to mark the intersection of the two lines and drill a 7/16″ hole as shown in Fig. 1-1. NOTE: Illustration is for long bed, D-cab short bed uses the same process. 2. D-ring Assembly Preparation Left Side (a) Insert the D-ring Assembly into the previously drilled hole. (b) Hold the D-ring Assembly in place by using a strip of duct tape.

Victory Vegas Rear LED Turn Signal Assembly Installation Manual

0

Filed Under (Victory) by admin on 31-10-2010

download
Step 1 •Prior to installation it is recommended that you perform a Pre-Function check. To do so, remove the left side battery cover from the bike and expose the post terminals. Hold the positive red lead from the turn signal to the positive red lead of the battery and then place the negative black lead from the turn signal to the negative black lead of the battery. Do one side at a time and ensure that both sides light prior to installation. Step 2 •Remove seat (passenger too if installed) •Remove fender “eyelashes” (required first if passenger seat is installed) •Remove the fender mounting bolts •Disconnect the rear turn signal and taillight harness connector located in the battery box compartment •Remove the fender by gentle prying outward and upward on one side to clear the mounting points, then the other side •Set aside on a flat and smooth surface to protect the fender’s finish (you may want to wrap it in a large towel) Step 3 •Turn the rear fender assembly upside down on a stable and covered/protected surface to prevent damaging the fender/paint •Remove the rear tail assembly and disconnect the wiring harness and license plate light. THIS PART IS NO LONGER NEEDED! Victory Vegas Rear LED Turn Signal Assembly Installation Guide •Remove the stock metal spacers shown below and replace them with the ¼” rubber spacers included in your accessory/installation kit. Step 4 •Place the turn signal assembly mounting arms over the rubber spacers. Align the turn signal in place so the space between the fender and the turn signal tube is consistent. After completing this step, place a small amount of Loc-Tite to the bolt and slowly tighten the stock nuts snugly in place, (extreme over-tightening may damage turn signal or fender lip). You should not need to loosen the mounting arms which are attached to the turn signal bracket to obtain the ideal fit; they are pre-assembled to be aligned. Please also note that due to manufacturing tolerances in the production of the fender, the rolled inner lip of it may interfere with the turn signal assembly seating properly. If this is the case, the lip can be tapped down flush with a rubber mallet or other appropriate tool. Take the necessary precautions to maintain your fender’s finish should this step be necessary. Step 5 •Run the wiring of the turn signal assembly in an appropriate/desireable path to the stock wiring harness. See picture below as an example. Once the wires are run, cut any excess wire and install the bullet connectors (included in the installation/accessory package) to the end of the wires. Due to the small gauge of the wire it’s suggested that you double it over before placing it into the bullet connector and solder it in place. Wire as follows: