yamaha stratoliner recalls

You search Auto repair manual PDF yamaha stratoliner recalls, if there are search results will appear below. If search results do not exist, please search by others keyword.



  yamaha stratoliner recalls Direct Download speed 5282 Kb/s

  yamaha stratoliner recalls Full Version speed 6162 Kb/s



YAMAHA ROADLINER / STRATOLINER Fuel Injected INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 28-10-2010

download
1. Be sure the main switch is in the off position during the installation process. Failure to do this will cause the “check engine” light to be set. 2. Remove seat exposing the Electronic Control Unit (ECU) and battery. 3. Remove the right side coil cover by removing two allen screws and gently pulling. 4. Disconnect the 6 pin factory connector behind the ignition coils. (Fig 1) 5. Connect Fuelpak 6 pin connectors in-line with factory connectors. 6. Disconnect 3 pin factory connectors behind the ignition coils and connect Fuelpak 3 pin connectors in-line with factory connectors. 7. Route Fuelpak harness up to battery area and reinstall coil side cover. 8. Connect Fuelpak black wire to negative ground wire. (Fig 2) 9. Locate factory 2 pin connector with brown and black wires. Disconnect empty connector and attach Fuelpak red wire connector. 10. Connect Fuelpak 10 pin connector to Fuelpak harness. 11. You are now ready to set-up your Fuelpak. INSTALLATION INSTRUCTIONS FOR P/N 65001 READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION FUEL INJECTION MANAGEMENT SYSTEM ROADLINER / STRATOLINER NOTICE: Fuelpak is intended for racing or off-highway use only, and is not legal for sale or use in California on pollution-controlled vehicles. PLEASE NOTE: FUELPAK USE REQUIRES A HIGH PERFORMANCE AIR FILTER. HOW IT WORKS ENTERING VALUES 1. Remove Fuelpak clear case cover by removing all four screws, save hardware . 2. Turn on main power with key, but do not start engine. Fuelpak display should light up, if not, turn power off and verify the connectors are fully seated. 3. Refer to Fuelpak Setting Reference to locate the Setting Values specific to your bike and exhaust system. If you do not find your setting, visit fuelpakfi.com or call tech support at (562) 921-0071. 4. Starting with mode 1 selected, press the value (+) or the value (-) buttons to input the correct value as indicated in your Setting Value. After entering your first value, press the mode select button to move to mode 2 and enter the value. Continue until you have entered the value for each of the first 18 mode positions. Each time the value (+) is pressed, the value increases by one number. Each time the value (-) is pressed, the value decreases by one number. (Please refer to the “How It Works” section directly above if you have questions about this step. 5. As the next procedure, after you have entered in your values for the first 18 modes, press the mode select button to move to mode 19. Fully twist open the throttle and return to idle position to calibrate the Fuelpak to your bike. 6. By pressing the mode select button twice, move to mode 21 and verify that it reads “0″ with the throttle closed, “50″ at approximately half-throttle and “99″ when fully opened; if not, repeat step 5. Do not proceed to step 7 until mode 21 is verified.

YAMAHA MOTOR CORPORATION, U.S.A. STREET & ENDURO MOTORCYCLE LIMITED WARRANTY

0

Filed Under (Yamaha) by admin on 27-12-2011

download
GENERALEXCLUSIONS from this warranty shall include any failures caused by: a. Competition or racing use. b. Installation of parts or accessories that are not qualitatively equivalent to genuine Yamaha parts. c. Abnormal strain, neglect, or abuse. d. Lack of proper maintenance. e. Accident or collision damage. f. Modification to original parts. g. Damage due to improper transportation. SPECIFIC EXCLUSIONS from this warranty shall include parts replaced due to normal wear or routine maintenance. THE CUSTOMER’S RESPONSIBILITY under this warranty shall be to: 1. Operate and maintain the motorcycle as specified in the appropriate Owner’s Manual. 2. Give notice to an authorized Yamaha motorcycle dealer of any and all apparent defects within ten (10) days after discovery, and make the machine available at that time for inspection and repairs at such dealer’s place of business. You may locate your nearest authorized Yamaha dealer through your local telephone directory. WARRANTY TRANSFER: To transfer any remaining warranty from the original purchaser to any subsequent purchaser, it is imperative that the machine be inspected and registered for warranty by an authorized Yamaha motorcycle dealer. In order for this warranty to remain in effect, this inspection and registration must take place within ten (10) days after transfer. Areasonable dealer imposed fee may be charged for the inspection. In no case will warranty be extended beyond the original period. EMISSIONS CONTROLSYSTEM WARRANTY Yamaha Motor Corporation, U.S.A. also warrants to the ultimate purchaser and each subsequent purchaser of each Yamaha motorcycle covered by this warranty with a displacement of 50cc or greater, that the vehicle is designed, built, and equipped so as to conform at the time of sale with all U.S. emissions standards applicable at the time of manufacture and that it is free from defects in materials and workmanship which would cause it not to meet these standards within the periods listed immediately below. Failures other than those resulting from defects in material or workmanship which arise solely as a result of owner abuse and/or lack of proper maintenance are not covered by this warranty.

Incoming search terms:

YAMAHA ROADLINER AND STRATOLINER LAY DOWN LICENSEPLATE/ TAIL INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 29-01-2011

download
1. Remove the license plate. Remove the license plate holder assembly from the rear fender (three 8mm Allen bolts 5mm wrench). Remove the five 4mm Allen screws underneath the rear fender which secure the taillight/turn signal assembly to the rear fender (3mm wrench). As shown in photo #2, pull the taillight assembly out away from the fender, turn it over, place a towel or rag between the light and fender and allow it to rest on the fender. 2. Locate the supplied triangular license plate mounting block, two 8 x 20mm Allen screws with holes driiled thru and three rubber washers. Place the two Allen screws thru the upper holes in the block and the rubber washers over the screws on the backside of the block. Start the screws into the upper holes on the fender. Use one of the three screws removed earlier from the original mount in the remaining lower hole of the new block sliding the remaining rubber washer between the block and fender. Tighten all three Allen screws secure enough to compress the rubber washers (4-6 ft lbs.). 3. Locate the supplied license plate mounting plate and LED lights. Cut off the excess red and black wires at the end of the black loom or tube. Referring to photo (1) thread the wires of the LED lights thru the small holes in the mounting plate, peel the cover from the adhesive backing on the lights and press them firmly into place as shown. 4. Locate the three supplied ¼” x ½” flat head Allen screws. Hold the plate up to the mounting block installed earlier with the wires at the bottom of the plate. Thread the wires from the LED lights thru the holes in the upper bolts of the block. Install the plate onto the block using the three flat head screws being sure to keep the exposed wire behind he plate as short as possible and fitting into the slot or cut out at the edge of the block. Snug the screws and again check to see tat the wires are in the slot or cut out in the block and do not become pinched as the screws are tightened. Tighten the screws securely. 5. Where the wires from the taillight go thru the fender there is a grommet, pull this grommet out from the fender. Thread the wires from the LED lights thru the grommet with the other wires. Replace the grommet into the fender and remove any slack from the wires under the fender. Cut the LED wires off at 6″ past the grommet.

YAMAHA ROADLINER AND STRATOLINER LAY DOWN LICENSEPLATE/ TAIL LIGHT INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 29-01-2011

download
1. Remove the license plate. Remove the license plate holder assembly from the rear fender (three 8mm Allen bolts 5mm wrench). Remove the five 4mm Allen screws underneath the rear fender which secure the taillight/turn signal assembly to the rear fender (3mm wrench). As shown in photo #2, pull the taillight assembly out away from the fender, turn it over, place a towel or rag between the light and fender and allow it to rest on the fender. 2. Locate the supplied triangular license plate mounting block, two 8 x 20mm Allen screws with holes driiled thru and three rubber washers. Place the two Allen screws thru the upper holes in the block and the rubber washers over the screws on the backside of the block. Start the screws into the upper holes on the fender. Use one of the three screws removed earlier from the original mount in the remaining lower hole of the new block sliding the remaining rubber washer between the block and fender. Tighten all three Allen screws secure enough to compress the rubber washers (4-6 ft lbs.). 3. Locate the supplied license plate mounting plate and LED lights. Cut off the excess red and black wires at the end of the black loom or tube. Referring to photo (1) thread the wires of the LED lights thru the small holes in the mounting plate, peel the cover from the adhesive backing on the lights and press them firmly into place as shown. 4. Locate the three supplied ¼” x ½” flat head Allen screws. Hold the plate up to the mounting block installed earlier with the wires at the bottom of the plate. Thread the wires from the LED lights thru the holes in the upper bolts of the block. Install the plate onto the block using the three flat head screws being sure to keep the exposed wire behind he plate as short as possible and fitting into the slot or cut out at the edge of the block. Snug the screws and again check to see tat the wires are in the slot or cut out in the block and do not become pinched as the screws are tightened. Tighten the screws securely. 5. Where the wires from the taillight go thru the fender there is a grommet, pull this grommet out from the fender. Thread the wires from the LED lights thru the grommet with the other wires. Replace the grommet into the fender and remove any slack from the wires under the fender. Cut the LED wires off at 6″ past the grommet. 6. Referring to photo (2) remove 2″ of the black tubing exposing the red and black wires on the LEDs. Locate the supplied brake/tail light dual function element (a red wire at one end with a red and orange wire at the other) and wire connectors. Cut all three wires on the dual element to 3″ long. Strip the end of the single red wire on the element and both of the red wires from the LEDs then connect them using one of the blue butt connectors. Connect the two black wires from the LEDs to any one of the black wires on the tail light or signals using one of the supplied splice connectors (place both black wires into one of the holes on the connector). Using the remaining splice connectors attach the red wire from the dual element to the yellow wire on the tail light and the orange wire to the blue wire on the tail light. Turn on the ignition and check that the LEDs are working both as tail and brake lights when the brakes are applied.

YAMAHA ROADLINER AND STRATOLINER PASSENGER FLOOBOARDS

0

Filed Under (Yamaha) by admin on 26-12-2010

download
1. Remove the passenger foot pegs pivot bolts and nuts. Remove the pegs, springs, detent ball and shims. 2. Locate the black mounting blocks supplied, notice they are marked “L” and “R” on their outer face. Install the blocks into the slots or clevises where you removed the foot pegs the tapered end should be facing down and the “L” and “R” to the outside. Install the original bolts and nuts removed earlier and tighten the bolts securely

YAMAHA ROADLINER AND STRATOLINER PASSENGER FLOOBOARD RELOCATION ARMS

0

Filed Under (Yamaha) by admin on 23-12-2010

download
1. When installing floorboards at the same time first refer to their instructions and using the longer right side black floorboards mounting block supplied with this set of relocation arms. Leave the final floorboards mounting bolt installed loosely at this time. 2. If installing the relocation arms after installing the floorboards at an earlier date proceed as follows. 3. On the left side remove the Allen screw below the floorboards pivot and remove the floorboard from the black mounting block. Remove the dowel pins from their holes on the block. Locate the left relocation arm (stamped “L” and “R” on their backsides). On the end with the clearance hole (not threaded) Place the two dowel pins into one of the two sets of holes which are directly across from each other (180 degrees apart). Hold the arm with the dowel pins up to the mounting block. Align the dowel pins with each of the three sets of holes in the block one at a time noting the height of the opposite end of the arm where the floorboard will mount. Move the dowel pins to the other set of holes on the arm and again hold the arm with the dowel pins up to the blocks three sets of holes. Choose the set of holes in both the block and arm which will set the floorboard to the desired height and place the arm with the dowel pins onto the block. Using one of the button head Allen screws supplied bolt the arm to the block and tighten securely. 4. Locate two of the dowel pins supplied and one of the Allen screw removed earlier. Place the dowel pins into the holes of the arm which allow the floorboard to be level or parallel to the ground. Place a drop of loctite on the threads of the screw and tighten securely. Install the right floorboard in the same manner. 5. On the right side remove the floorboard from the mounting block. Remove the mounting block and replace it with the longer one supplied. Install the right arm in the same manner as the left using the set of dowel pin holes to match the height or angle of the left arm. Install the right floorboard and tighten securely. Recheck all fasteners for tightness.

Yamaha Stratoliner/ Road liner REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 09-01-2012

download
The LegUp® system has many components. Pleased be sure you have them all before starting your installation. COMPONENTS: 1) Control Switch Box 2) Linear Actuator 3) On-board Computer Module 4) Proximity Sensor 5) Leg Support Stand 6) Leg/Wheel System 7) Hardware Bag 8) Actuator Bracket If you believe you are missing any parts, please contact Chopper Design at 407-834-5007, and we will rectify the situation. Figure 1 6 PREPARE FOR INSTALLATION Place the motorcycle on an acceptable bike lift. You will need to keep the bike on its wheels for most of the installation, and jack the rear wheel off the lift for some portion of the installation. Make SURE the motorcycle is secure on the lift! Remove the seat, saddlebags and side covers, they are not needed until the very end of the installation. We are now ready to begin! 7 INSTALL LEG SUPPORT STAND LegUp has developed a new, stronger attachment system which holds the Leg system to the bike! You will need to remove the two Exhaust Bolts from the exhaust bracket in order to install the support stand. These Bolts are replaced with two from the kit. Remove the Black button-head bolt from the left side of the bike, directly below the left foot peg. This bolt will be replaced. If inserted into the stand, the long stainless steel shaft with the small bolts in the end should have one of the bolts removed, and be slid out of the pipe in the stand. Just set this aside for now. The first step is to install the right upright described above, outside the exhaust bracket and frame. The spacer goes to the inside against the exhaust bracket then the 90 degree bracket outside with two bolts supplied. Get the bolt holes to line up, and install the bolts (with a bit of blue Locktite on the bolts) loosely. The other, longer 90 degree bracket (the one with the rounded relief on it) is hung from the left side of the bike next where you removed the button-head bolt earlier. Again, some Locktite and keep the bolt loose for now!

YAMAHA ROADLINER / STRATOLINER REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 04-01-2012

download
1. Cover the right frame tube in front of the exhaust with duct tape or any suitable material to protect frame during exhaust removal. 2. Remove the three capscrews holding the muffl er assembly to the support bar, loosen the muffl er clamp and carefully remove the muffl er from the motorcycle. 3. Remove and save the two 12mm bolts from the right side fl oorboard assembly (Figure 1) and carefully lower the fl oorboard out of the way. NOTE: Support the fl oorboard with a block of wood or other appropriate material, do not let it “hang” by the brake switch wire. 4. Remove the chrome cover over the power valve pulley. Using a 10mm wrench, remove both cables attached to the power valve pulley (Figure 2). 5. Remove and save the 5mm capscrew on the rear side cover to gain access to the O2 sensor harness plug and unplug O2 sensor from harness (Figure 3). 6. Remove the 4 nuts holding the exhaust system and carefully remove the exhaust system from the motorcycle (may require assistance). NOTE: It may be necessary to loosen the heatshield clamps to access the nuts on the front cylinder. 7. Trace the power valve cables to the drive motor (just under the rear fender on the right side). Remove the power valve cables and mounting clips from the motorcycle. 8. Using a 22mm wrench, carefully remove the O2 sensor from stock exhaust system and save for reuse with the new system. 9. Remove the plastic cover over the clutch banjo bolt (Figure 4). 10. Check the stock exhaust gaskets to be sure they are in good shape. If you have any doubts as to their condition, replace them

Yamaha Stratoliner 2006 3" Big Straights REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 02-01-2012

download
1. Remove right side Foot peg assembly or Floorboard. (Whichever is applicable to your model.) 2. Remove bolts that are holding muffler at rear mounting bracket. 3. Remove Cables from exhaust valve. 4. Remove O2 Sensor from pipe. 5. Remove the two nuts that secure the rear exhaust header pipe to the rear cylinder head. 6. Remove the two nuts that secure the front exhaust header pipe to the front cylinder head. 7. Remove complete pipe assembly. Hard-Krome Exhaust System Installation NOTE: Take care when fitting this Hard-Krome aftermarket exhaust system on your motorcycle. It has been designed to replace a STOCK exhaust system on a motorcycle with its engine, frame and other components in their STOCK design, configuration and location. WARNING : Re-check and re-tighten ALL fasteners and supports after 50 miles, then re-check and tighten as necessary on a periodic basis to ensure proper operation and performance. NOTE: All fasteners should be loose during initial installation to ensure proper fit and location of the new exhaust system. 1. Install new exhaust gaskets. 2. Install mounting bracket using Bolts with flat & lock washers. (See Illustration) 3. Install O2 Sensor onto front pipe and install front pipe onto front cylinder, taking care to not scratch chrome surfaces on pipe, engine or motorcycle. 4. Install the two nuts to secure the flange that holds the exhaust header pipe to the front cylinder head — DO NOT TIGHTEN NUTS! 5. Install 3/8-16 Square nut into each slotted bracket of front pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 6. Carefully install rear pipe onto rear cylinder. 7. Install the two nuts to secure the flange that holds the exhaust header pipe to the rear cylinder head — (Remove chrome plastic valve cover to access top nut) — DO NOT TIGHTEN NUTS! 8. Install 3/8-16 Square nut into each slotted bracket of rear pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 9. Tighten the two bolts that secure the rear exhaust header pipe flange. 10. Tighten the two bolts that secure the front exhaust header pipe flange. 11. Tighten front pipe bolts at mounting bracket. 12. Tighten rear pipe bolts at mounting bracket. 13. Reinstall foot peg assembly or floorboard. 14. If applicable to your model install foot peg relocating brackets and foot pegs as shown in illustration.

YAMAHA YZF-R1R/ YZF-R1RC OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 03-12-2010

download
1. Right turn signal indicator light “” 2. Fuel level warning light “” 3. Oil level warning light “” 4. Neutral indicator light “” 5. Engine trouble warning light “” 6. High beam indicator light “” 7. Left turn signal indicator light “”
INSTRUMENT AND CONTROL FUNCTIONS 3-3 3 EAU04895 Oil level warning light “” This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical cir- cuit. NOTE: Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a malfunction. This model is also equipped with a self-diagnosis device for the oil level detection circuit. If the oil level detection circuit is defective, the following cycle will be repeated until the malfunction is corrected: The oil level warning light will flash ten times, then go off for 2.5seconds. If this occurs, have a Yamaha dealer check the motor- cycle. EAU00061 Neutral indicator light “” This indicator light comes on when the transmission is in the neutral position. EAU04896 Engine trouble warning light “” This warning light comes on or flashes when an electrical circuit monitoring the engine is defective. When this occurs, have a Yamaha dealer check the self-diagnosis system. (See page 3-7 for an explanation of the self-diagnosis device.) The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical circuit. EAU00063 High beam indicator light “” This indicator light comes on when the high beam of the headlight is switched on

Incoming search terms: