tzr 125 1992 down on power

You search Auto repair manual PDF tzr 125 1992 down on power, if there are search results will appear below. If search results do not exist, please search by others keyword.



  tzr 125 1992 down on power Direct Download speed 5282 Kb/s

  tzr 125 1992 down on power Full Version speed 6162 Kb/s



2008 KTM Model Engine Oil Recommendation Chart

0

Filed Under (KTM) by admin on 24-11-2010

download
2008 Model Type Recommended Engine Oil Type Quantity SPORTMINICYCLES AC 50 SX MINI Motorex ATF Super (Dexron II Gear Oil) 0.15-0.2 L SPORTMINICYCLES LC 50 SX JUNIOR Motorex ATF Super (Dexron II Gear Oil) 0.15-0.2 L 50 SX Motorex ATF Super (Dexron II Gear Oil) 0.15-0.2 L 65 SX Motorex Top Speed 4T 15W50 0.5L SX 2 STROKE 85 SX Motorex Top Speed 4T 15W50 0.5 L 105 SX Motorex Top Speed 4T 15W50 0.5 L 125 SX Motorex Top Speed 4T 15W50 0.7 L 144 SX Motorex Top Speed 4T 15W50 0.7 L 250 SX Motorex Top Speed 4T 15W50 0.7 L SX 4 STROKE 250 SX-F Motorex Power Synt 4T 10W50 1.1 L 450 SX-F Motorex Power Synt 4T 10W50 1.35 L 505 SX-F Motorex Power Synt 4T 10W50 1.35 L CROSS COUNTRY 2 STROKE 65 XC Motorex Top Speed 4T 15W50 0.5L 85 XC Motorex Top Speed 4T 15W50 0.5L 105 XC Motorex Top Speed 4T 15W50 0.5 L 200 XC Motorex Top Speed 4T 15W50 0.7 L
200 XC-W Motorex Top Speed 4T 15W50 0.7 L 250 XC Motorex Top Speed 4T 15W50 0.7 L 250 XC-W (e) Motorex Top Speed 4T 15W50 0.7 L 300 XC Motorex Top Speed 4T 15W50 0.7 L 300 XC-W (e) Motorex Top Speed 4T 15W50 0.7 L CROSS COUNTRY 4 STROKE 250 XC-F Motorex Power Synt 4T 10W50 1.1 L 250 XC-F-W Motorex Power Synt 4T 10W50 1.1 L 450 XC-F Motorex Power Synt 4T 10W50 1.35 L 450 XC-W (R) Engine – Motorex Power Synt 4T 10W50 Gearbox – Motorex 4T 10W50 0.7 L 0.9 L 505 XC-F Motorex Power Synt 4T 10W50 1.35 L 530 XC-W (R) Engine – Motorex Power Synt 4T 10W50 Gearbox – Motorex 4T 10W50 0.7 L 0.9 L ENDURO RACING 450 EXC (R) Engine – Motorex Power Synt 4T 10W50 Gearbox – Motorex 4T 10W50 0.7 L 0.9 L 530 EXC (R) Engine – Motorex Power Synt 4T 10W50 Gearbox – Motorex 4T 10W50 0.7 L 0.9 L SUPERMOTO LC4 690 Supermoto Motorex Power Synt 4T 10W60 Approx. 2.0 L SPORT ATV 450 XC Motorex Power Synt 4T 10W50 2.0 L 525 XC Motorex Power Synt 4T 10W50 2.0 L LC8 950 Super Enduro (R) Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 990 Adventure Orange Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 990 Adventure Black Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 990 Adventure S Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 990 Super Duke Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 990 Super Duke R Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L

Incoming search terms:

2006 Model Engine Oil Recommendation Chart

0

Filed Under (KTM) by admin on 26-11-2010

download
2006 Model Type Recommended Engine Oil Type Quantity SPORTMINICYCLES AC 50 MINI ADVENTURE Motorex ATF Super (Dexron II Gear Oil) 0.15-0.2 L 50 SENIOR ADVENTURE Motorex ATF Super (Dexron II Gear Oil) 0.15-0.2 L SPORTMINICYCLES LC 50 SX JUNIOR Motorex Top Speed 4T 15W50 0.15-0.2 L 50 SX Motorex Top Speed 4T 15W50 0.15-0.2 L 65 SX Motorex Top Speed 4T 15W50 0.3L SX 2 STROKE 85 SX Motorex Top Speed 4T 15W50 0.5 L 105 SX Motorex Top Speed 4T 15W50 0.5 L 125 SX Motorex Top Speed 4T 15W50 0.7 L 250 SX Motorex Top Speed 4T 15W50 0.7 L SX 4 STROKE 250 SX-F Motorex Power Synt 4T 10W50 1.1 L 450 SX Motorex Power Synt 4T 10W50 1.25 L 525 SX Motorex Power Synt 4T 10W50 1.25 L CROSS COUNTRY 2 STROKE 200 XC Motorex Top Speed 4T 15W50 0.7 L 200 XC-W Motorex Top Speed 4T 15W50 0.7 L 250 XC Motorex Top Speed 4T 15W50 0.7 L 250 XC-W Motorex Top Speed 4T 15W50 0.7 L 300 XC Motorex Top Speed 4T 15W50 0.7 L 300 XC-W Motorex Top Speed 4T 15W50 0.7 L CROSS COUNTRY 4 STROKE 450 XC Motorex Power Synt 4T 10W50 1.25 L 525 XC Motorex Power Synt 4T 10W50 1.25 L ENDURO RACING 400 EXC Motorex Power Synt 4T 10W50 1.25 L 450 EXC Motorex Power Synt 4T 10W50 1.25 L 525 EXC Motorex Power Synt 4T 10W50 1.25 L ADVENTURE LC8 950 Adventure orange Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 950 Adventure black Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 950 Adventure S Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L SUPERMOTO RACING 450 SMR Motorex Power Synt 4T 10W50 1.25 L 560 SMR Motorex Power Synt 4T 10W50 1.25 L SUPERMOTO LC4 625 SMC Motorex Power Synt 4T 10W50 Approx. 2.1 SUPERMOTO LC8 950 Supermoto orange Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L 950 Supermoto black Motorex Power Synt 4T SAE 10W50 (for temperatures over 32° F) and 5W40 (for temperatures under 32° F) Approx. 3.0 L

Incoming search terms:

Harley Davidson Power Pod Switch Housing Throttle Bracket Installation Instructions

0

Filed Under (Harley Davidson) by admin on 19-03-2012

download
Attach the “Y” bracket to the Power Pod by using the two Power Pod socket head screws that come in your parts kit. (This bracket may already be attached from the factory. ) 2) Remove the two screws on the Right Hand switch housing on your Harley Davidson motorcycle and reinstall them through the two “Y” bracket open holes and back into the switch housing holes. Tighten snugly. In this mounting position, the heads of the two socket head screws holding the “Y” bracket to the Power Pod should be touching the handlebar; this is necessary as it grounds the unit for proper operation. If the unit is not grounded properly, it will not operate. 3) Run the Power Pod’s 60″ power cord to your battery. Make sure as you hide the cord on the way to the battery, that your handlebars turn freely and that the cord does not come in contact with hot engine parts that may melt the wire over time. 4) At some point, before reaching the battery, attach (using the two butt connectors) the in-line fuse holder. TIP: Keeping the in-line fuse holder in an easy to access place (like under a side panel etc) rather than under the seat, may help you service the fuse easier in case of a blown fuse. In most cases, it’s easier to pull a side panel off than it is to remove a seat! 5) Attach the Power Pod lead wire (with in-line fuse now already attached) directly to the battery for power at anytime without using the key. The hot lead can also be run to the fuse box which will require using the ignition switch to “Accessory” or “ON” in some cases. TIP : Always use the in-line fuse for safety. 6) Insert the 20 amp fuse into the in-line fuse holder. Strap down with zip-ties any loose wires and you’re done!

Toyota and Lexus Clogged Power Steering Reservoir Filter

0

Filed Under (Toyota Manuals) by admin on 02-10-2011

download
Clogged Power Steering Reservoir Filter – Toyota & Lexus Toyota and Lexus vehicles with power steering. Noise coming from the power steering pump or reduced assist from the power steering system. Noise or reduced assist may be caused by restriction in the power steering fluid reservoir. Most Toyota/Lexus-style reservoirs have a filter screen at the bottom. Over a period of time this filter could get clogged causing the restriction of fluid. Replace any hose that shows signs of cracking or internal deterioration. Thoroughly flush the power steering system; then remove the reservoir for cleaning as follows: 1. Clean the exterior and interior of reservoir with new power steering fluid or suitable solvent. 2. Blow off the filter screen using pressurized air until restriction or clog is removed. 3. Using a flashlight, check to make sure that the filter screen is free of debris. Note: Contamination may be an indication of internal breakdown of hoses, which must be replaced before operating the vehicle. Failure to replace bad hoses could damage both the pump and steering unit. 4. Reinstall reservoir, referring to the service manual for tightening specs and bleeding procedures.

CYCLE SOUNDS T-TAP POWER HARNESS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 21-04-2012

download
This t-tap plug is designed to work with Cycle Sounds audio systems. However it can be used to wire many add on 12 volt accessories to you Harley Davidson motorcycle. This plug is rated for 6-8 amps of power and should not be used for adding any product that is rated for more than the t-tap plug is rated for. Take the time to check the products power rating for which you want to install to make sure it is compatible with the t-taps amperage rating. Failure to do so couldlead to electrical failures, which could result in serious injuries or even death. it is possible to overload your motorcycles charging system by adding too many electrical accessories. U se amp meter to verify all power connections. Also check product power ratings for anything you are trying to install. Exceeding the maximum amperage can lead to electrical failures, which could result in serious injuries or even death. INSTRUCTIONS: Step 1: remove seat on bike and locate the wire harness under the seat that matches the plugs on the t-tap harness (2120-0026.) Location may vary between bike models. Step 2: unplug bike harness and snap each end of t-tap harness in correct plug opening. When finished connect power wires to the male plug.(all Cycle Sounds audio systems come pre wired with correct wire colors and terminals). When using this t-tap for any other 12 volt accessory, make sure the red and black wires are snapped into their proper pin connectors. Kit does not come with power terminals for the accessories device. See your local bike dealer for purchase of terminals

2003 – 2004 4Runner, 2004 Highlander, Prius, Sienna And Solara POWER WINDOW / ROOF INITIALIZATION PROCEDURES

0

Filed Under (Toyota Manuals) by admin on 17-10-2011

download
Turn the ignition switch ON. 2. Open the window halfway by pressing the power window switch. 3. Fully pull up the switch until the power window is fully closed and continue to hold the switch for at least three (3) seconds after the power window is fully closed. 4. Check that the “AUTO UP/DOWN” function operates normally. B. Back Door Power Window (4Runner) 1. Turn the ignition switch ON. 2. Open the back door glass. 3. Press the back door power window switch until the door glass is fully closed and continue to hold the switch one (1) second or more after the door glass is fully closed. 4. Check that the “AUTO UP/DOWN” function operates normally. C. Power Sliding Roof (4Runner, Sienna, Solara) 1. Turn the ignition switch ON. 2. Initialize the sliding roof by pressing and holding the TILT UP switch until the roof glass tilts upward fully (the roof glass automatically tilts downward slightly after fully tilting upward). 3. Release the switch. 4. Check that the “AUTO OPEN/CLOSE” function operates normally

Tacoma Power Steering Pump Improving Power Steering Reservoir modification

0

Filed Under (Toyota Manuals) by admin on 02-10-2011

download
For my SAS I decided to add hydraulic steering assist as it comes in real handy for rock crawling. I got the Redneck Ram setup from the folks at West Texas Off-road that includes rebuilding an earlier IFS steering box along with drilling and tapping the box for the included ram. One of the down sides of adding a ram is that it slows the steering down because the stock steering pump has to supply the added volume for the hydraulic ram. Another is that it creates a fluid volume change in the system reservoir that needs to be compensated for in some way. After doing some reading on the West Texas site about how to go about modifying a Saginaw pump and reading up on earlier Toyota pump mods for steering assist setups on the Pirate board, I decided to give it whirl and see what I could do about the Tacoma pump. Chuck Gardella was kind enough to supply me with a blown pump that I could rebuild and submit to my endless fiddling and tinkering. I plan to give him my pump in return when I get this one done and installed. You need to do something to allow for more room in the reservoir for the standard hydraulic ram assist setup so I decided to tackle the reservoir first. The reason you need the extra space is because the ram is unbalanced. That is there is a rod on one side of the cylinder and not on the other side so the volume of the fluid has to change in the system to account for the volume of the rod as it travels back and forth. I calculated the volume of the rod that I have at full stroke to be about 2 oz or so. This would equate to plus or minus up to 2 oz. in the pump reservoir. Well first off, it’s no wonder why so many folks boil their steering pumps over with heavy wheeling and have so many other steering problems. The stock power steering reservoir doesn’t even rate pint sized

KTM 125/ 200/ 250/ 300 SX, MXC, EXC SERVICE MANUAL

0

Filed Under (KTM) by admin on 28-11-2010

download
Compression damping of shock absorber (MXC, EXC) The compression damping (during compression) can be adjusted for the MXC and EXC shock absorbers (Mono Compression Control). The degree of damping can be adjusted by turning adjusting screw 1 with a screwdriver. Turning in a clockwise direction will increase the damping, turning in a counterclockwise direction will decrease the damping. STANDARD ADJUSTMENT: -Turn the adjusting screw clockwise to the stop. -Then turn the adjusting screw counterclockwise, counting the number of clicks that corresponds to the respective type of shock absorber. Type White Power 1218X757…………..17 clicks Type White Power 1218X759…………..17 clicks * WARNING * THE DAMPING UNIT OF THE SHOCK ABSORBER IS FILLED WITH HIGH – COMPRESSION NITROGEN . NEVER TRY TO TAKE THE SHOCK ABSORBER APART OR TO DO ANY MAINTEN – ANCE WORK YOURSELF . SEVERE INJURIES COULD BE THE RESULT . NEVER UNSCREW THE BLACK SCREW 2 CONNECTION (24 MM ). Rebound damping of shock absorber (SX, MXC, EXC) By using the adjusting screw 3 , the degree of damping of the rebound can be adjusted. Turn the knob to the right side to increase damping, turn it to the left side to reduce damping during rebounding. STANDARD ADJUSTMENT: -Turn the adjusting screw clockwise to the stop. -Then turn the adjusting screw counterclockwise, counting the number of clicks that corresponds to the respective type of shock absorber. Type White Power 1218X756…………..28 clicks Type White Power 1218X757…………..28 clicks Type White Power 1218X759…………..26 clicks * WARNING * THE DAMPING UNIT OF THE SHOCK ABSORBER IS FILLED WITH HIGH – COMPRESSION NITROGEN . N EVERTRYTOTAKETHESHOCKABSORBERAPARTORTODOANYMAINTE – NANCE WORK YOURSELF . SEVERE INJURIES COULD BE THE RESULT . NEVER UNSCREW THE BLACK SCREW 4 CONNECTION (15 MM )

1997-1998 EFI Harley Davidson 1340 EVO Power Commander Installation Manual

0

Filed Under (Harley Davidson) by admin on 16-03-2012

download
1 Remove the seat. 2 Remove saddlebags if installed. 3 Remove left and right side covers. 4 Remove the battery (negative terminal first). 5 Loosen the two 7/16 nuts that retain the ECU (Fig. A) 6 From the left side (underneath the left side cover area) feed the PC III connectors in front of battery tray, and out the right side (in front of the ECU bracket)(Fig. B). 7 Attach PC II module to battery box. First, clean the PCIII and battery box with the supplied alcohol wipe. Using the supplied velcro attach PCIII to the battery box. Also secure the unit with the included zip ties. If your bike has cruise control, attach the unit to the face of the cruise control module (Fig. C). 8 Disconnect the large connector from the ECU. Remove the rubber dust shield. 9 Install the dust shield onto the matching connector on the PCIII. Zip tie the rubber dust shield to the PCIII connector with zip tie provided. 10 Plug the PCIII connector into the stock ECU. 11 Plug stock connector into the remaining connector from the PCIII (Fig. D). 12 Tighten the two 7/16 nuts that retain the ECU. 13 Route the connectors alongside the ECU and install the right side cover. 14 Replace the battery, the left side cover and the seat. 8 5 Power Commander Connnector Stock Connnector Fig.D Fig.E Adjust Idle Speed here Fig.F Adjusting Your Power Commander Your Power Commander has been programmed with a base map for your application. You can adjust the base map or install an alternate map using your Computer. Please refer to the supplied CD-Rom for more information. You can also adjust your Power Commander using the face plate buttons as described below. 1. With the ignition off, hold down all three buttons on the Power Commander unit. 2. While still holding down the buttons, turn the ignition on. 3. Release buttons

Incoming search terms:

2000-2001 Kawasaki ZX-12R Power Commander Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1) Remove the passenger seat or solo seat cover section. 2) Remove the main seat. 3) Remove the fuel tank shell and prop the front of the fuel tank up. 4) Disconnect the fuel injector connector shown in Fig. A. This connector is located on the backside of the frame towards the bottom of the fuel tank. There are two connectors side by side, disconnect the one on the left. 5) Plug the connectors from the Power Commander in line of these connectors. (Fig. B) 6) Disconnect the rear brake light connector. (Fig. C) Plug the connectors from the Power Commander in line of these connectors. (Fig. D). 7) Connect the ground wire from the Power Commander to the negative side of the battery (Fig. E). 8) Mount the Power Commander in the rear trunk area using the supplied velcro strips. 9) Reinstall the fuel tank and its shell. 10) Reinstall main seat and passenger seat/solo cover

Incoming search terms: