tri glide lift kit install

You search Auto repair manual PDF tri glide lift kit install, if there are search results will appear below. If search results do not exist, please search by others keyword.



  tri glide lift kit install Direct Download speed 5282 Kb/s

  tri glide lift kit install Full Version speed 6162 Kb/s



HARLEY DAVIDSON FRONT THUNDERSTAR WHEELS INSTALLATION

0

Filed Under (Harley Davidson) by admin on 08-11-2010

download
Remove existing front wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to FRONT WHEEL in service manual. For FLSTC and FLSTN Models: Discard moon-style hub cap. -J04065 1 of 8 For FXSTD Models: Discard the tapered r ight side wheel spacer. Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c) NOTE • For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771- 07, 43609-07, 44323-07, 44282-07, 44322-07, 43975-07, 43602-07 and 43773-07 install short valve stem (43157- 83A) included in the installation kit. • For Kits 40943-09, 40966-09 and 40996-09 install long valve stem (43206-01) included in the installation kit. 2. See Figure 2. Install valve stem assembly (L, M or N) on wheel. Refer to TIRES in service manual. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in Service Manual. NOTES Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771-07, 43609-07, 40943-09, 40966-09 and 40996-09: • The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and/or DOT markings to identify it as the brake disc and primary bearing side. • Install the wheel so that the valve stem is on the right side of the motorcycle. For Kits 44323-07, 44322-07 and 44282-07: • Install the wheel so that the hub markings are on the left side of the motorcycle. The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and hub markings to identify it as the primary bearing side. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). • The gross axle weight ratings is unaffected by the installation of this wheel on a vehicle equipped with a 21-inch wheel. For Kits 43975-07, 43773-07, and 43602-07: • The wheel has a machined groove (item 5, Figure 2) in the hub face to identify the right side. • For 2007 and later FX Softail Models and 2008 and later FXDWG: The left side of the wheel is the primary bearing side. For all other models the right side of the wheel is the primary bearing side. • For Kit 43602-07: An arrow is engraved into the right side hub to indicate the direction of rotation. • For Kits 43975-07 and 43773-07: An arrow is cast between the spokes on the right side to indicate the direction of rotation. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake-disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). 4. Install wheel assembly parts from the appropriate Service Parts table for this fitment and stock brake disc. Discard parts from the installation kit that are not required. Refer to FRONT WHEEL in Service Manual. 5. For FLSTC and FLSTN Models: Install wheel kit and right side wheel spacer provided in installation kit. For FXSTD Models: Install wheel kit, stock left wheel spacer and right side wheel spacer from installation kit in place of the tapered right side wheel spacer discarded in Step 1. Refer to FRONT WHEEL in service manual. For FXSTS Models: Install the left side wheel spacer provided in the kit between the stock left wheel spacer and the left fork. All other models: Install wheel spacers previously removed. 6. Install front wheel (1), stock axle and stock axle nut. Refer to FRONT WHEEL in service manual

Incoming search terms:

PRO-CYCLE AND PRO-CYCLE XLT 1,000-Lbs. Capacity Motorcycle Lift

0

Filed Under (Tips and Review) by admin on 27-11-2010

download
1. Always inspect the lift for freight damage and make note of any damage on the bill of lading. 2. In case of freight damage, call the truck line immediately and report the damage as a freight claim. Final Set-Up for model Pro-Cycle This lift is more than 90% factory pre-assembled. The following steps will guide you through the final set-up. IT WOULD BE EASIER FOR TWO MEN TO COMPLETE FOLLOWING STEPS. 1. Unpack the lift from the shipping skid. With the lift table up side down, connect the air hose to the air cylinder (Part # 26). 2. After tightening the hose to the cylinder, flip the lift over with the table surface up. 5 3. Lift up the table manually to the first lock position to make sure the lift is rising freely. Lubricateing the joints again before use will ensure a better performance of the lift. 4. Connect the other end of the air hose to the foot-operated valve. Then connect the foot- operated valve to 100 PSI air supply. DO NOT USE AIR SUPPLY WITH PRESSURE MORE THAN 100 PSI. 5. Release the safety bar by pushing the handle down. Operate the foot valve by stepping on the footpad forward to raise the lift. The safety bar should engage the ladder automatically while lift is rising. Step on the footpad again to set the pad in middle position to stop the lift when it reaches the desired height. ALWAYS LOWER LIFT IN THE NEAREST LOCKED POSITION BEFORE BEGINNING WORK. NEVER USE THE LIFT UNLESS YOU ARE IN A LOCKED POSITION. The lift should never be left unattended while attached to air pressure. Disconnect the air pressure when lift is not attended by qualified persons. 6. Install the vise using bolts and nuts supplied with the lift (part # 6 to 12). See fig #1. 7. Install the approach ramp by dropping it into the holes punched on the rear edge of the table. The final Set-Up for the Pro-Cycle model is complete

Incoming search terms:

Daytona 675 Motorcycle Race Kit Installation Manual

0

Filed Under (Triumph) by admin on 29-10-2010

download
Remove the existing cylinder head gasket in line with the procedures detailed in the Daytona 675 service manual. 2. Fit the chosen race kit cylinder head gasket following the procedures detailed in the Daytona 675 service manual. Caution The use of the following race kit cylinder head gaskets will require changes to the fuelling settings. To alter fuelling settings a third party programmable control unit will be required. Item Description Qty 1 Head gasket (t = 0.65mm) 1 1 Head gasket (t = 0.60mm) 1 1 * Page 7 of 29 © Triumph Designs Ltd 2007. Cams, Valve Spring & Sprocket Kits Parts Supplied Camshaft Inlet Kit – A9618055 Camshaft Exhaust Kit – A9618056 Valve Spring Kit – A9618058 Camshaft Sprocket Kit – A9618057 Warning The race kit must be fitted as a complete set. If it is not fitted as a complete set a failure may result which could cause loss of motorcycle control and an accident. Caution The use of the Camshaft, Valve spring & Sprocket race kits detailed below will require changes to the fuelling settings. To alter fuelling settings a third party programmable control unit will be required. 5 5 4 1 3 2 4 3 Item Description Qty 1 Cam assy, inlet, race 1 Item Description Qty 2 Cam assy, exhaust, race 1 Item Description Qty 3 Valve spring, 14.4id, race12 Item Description Qty 4 Sprocket, camshaft, 34T 2 5 Socket head cap screw, Encapsulated, M6x10 4
Page 8 of 29 © Triumph Designs Ltd 2007. NOTE •The standard inlet cam is 9.25mm max lift and 258.50o duration. The race kit inlet cam is 9.25mm max lift and 268.74o duration. •The standard exhaust cam is 8.5mm max lift and 246o duration. The race kit exhaust cam is 8.5mm max lift and 262.21o duration. •The race kit valve spring must be used in conjunction with the standard spring platforms and retainers. The fitted length of the race springs is the same as the standard spring. 1. The race kit valve springs should be assembled in the same manner as the standard valve springs. Follow the procedure detailed in section 3 of the Daytona 675 service manual. Ensure the springs are installed with the close wound, colour coded end of the springs facing downwards, towards the piston. 2. The race kit camshafts should be assembled in the same manner as the standard camshafts. Follow the procedure detailed in section 3 of the Daytona 675 service manual. 3. The race kit cam sprockets should be mounted and secured to the camshafts using the slotted holes in the sprocket. The slotted holes allow adjustment of the valve timing. The circular holes in the sprockets are for Triumph service tool T3880102 and should not be used to mount the sprockets to the camshafts. NOTE •No timing marks are included on the race sprockets. Race engines will typically have different depths skimmed off the cylinder head and, therefore require specific individual timing. 4. The camshafts should be timed using cam degreeing equipment which typically consists of a degree wheel, pointer, dial indicator and piston stop. Optimum cam timing will depend on the exact specification of the engine, but a recommended starting point is 104o IMOP (Inlet Maximum Opening Point) and 104o EMOP (Exhaust Maximum Opening Point). 5. Always check the inlet and exhaust piston to valve clearance for the timing selected to use, before running the engine. You must ensure both clearances are adequate. As a guide, the standard nominal piston to valve clearance is 1.3mm inlet & 1.5mm exhaust

Incoming search terms:

Harley Davidson Road Rod Saddle Bag System Kit INSTALLATION Instructions

0

Filed Under (Harley Davidson) by admin on 16-04-2012

download
Use locktite on all fasteners!! 2. Put bike on lift and place jack under frame. Raise bike to lift rear wheel. 3. If swing arm pivot shaft is drilled and tapped on each end, they need to be redrilled and tapped to 3/8-16 to a depth of _” deep. If you are unable to drill & tap your swing arm pivot shaft, you can purchase one from Cycle Visions (part #CV6121), See Harley Davidson® V-Rod® Service Manual Section 2, Page 2.89 for removal and installation instructions. 4. Remove seat, passenger seat, turn signal module, rear fender cover, turn signal license plate assembly, and rear foot peg assemblies. NOTE: Our bag system will not work with stock exhaust system… we recommend the 2-into-1 Supertrap, or you may use any exhaust system that is lower than the rear axle bolt. 5. Remove the two upper shock bolts. Relocate the shock spacer from the right side to the left side, and use the new spacer supplied on the right side. 6. Install front bag mount between frame and spacer (see Figure 1), reinstall shock bolts and torque to 31-50 lbs. 7. Install lower bag support frame to swing arm pivot shaft using the 3/8″ bolt through rear foot peg clevis and cover (see in Figure 2). NOTE: There is a right and left covers and bag support, install accordingly. Torque to 35 foot lbs. 8. Install rear fender front mounting tabs using 8mm 1.25 x _ and flat washers (supplied in kit) (see Figure 3). 9. Install upright saddlebag support brackets to the lower bag mount assembly and lower fender extension crossover mount. (see Figure 4). Torque to 25 lbs. NOTE: Install crossover mount with gusset facing down. 10. Remove license plate light from your rear turn signal bracket license plate assembly. Install license plate light on our license plate light bracket (see Figure 5). 11. Install the license plate bracket on the inside of the rear fender extension using the top holes of the license plate frame (see Figure 6 & 7). 12. Install fender washers on the inside of the fender extension (see Figure 8). 13. Install upper fender bracket to rear fender extension with a _-20 bolt supplied in kit (see Figure 9). 14. Install rear fender extension with chrome button fitted bolts. (see Figure 10 & 11). 15. To check alignment and fit of rear fender extension reinstall original rear fender. Once you have everything lined up and fitted, remove original rear fender, drill & tap (2) two 5/16 x 18 holes in rear fender support bracket (see Figure 12). 16. Install Harley Davidson® Part #70909-95 and 47449-97 bracket and receptacle on front and rear bag supports (see Figure 13 & 14). 17. Install Harley Davidson® Part #47449-97 bracket with receptable (see Figure 14). Make sure the bolts come from the inside out. This bracket is adjustable for location.

Incoming search terms:

HARLEY DAVIDSON CLUTCH CABLE ASSEMBLY INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-03-2011

download
36753-87A This kit fits 1987 and later FXLR model motorcycles. 36755-87A This kit fits 1987 and later FXRS/SP model motorcycles. 38601-89 This kit fits 1988 and later FLTC, FLTC-Ultra, FLHS, FLHTC FLHTC-Ultra and FLHTP model motorcycles. 38606-87A This kit fits 1987 and later FXR, FXRS and FXRT model motorcycles. 38607-87A This kit fits 1987 and later FLST, FXST, FXSTC, FXRP, FLTC, FLHT, FLHTP and FLHTC model motorcycles. 38617-95 This kit fits 1995 and later FXSTSB model motorcycles. 38647-98 This kit fits 1998 and 1999 FXSTB model motorcycles. 38661-00 This kit fits2000 and later FXDL, FXDS-CONV and FXDWG model motorcycles. 38664-00 This kit fits2000 and later FXSTD model motorcycles. 38665-00 This kit fits2000 and later FXSTB model motorcycles. 38666-00 This kit fits2000 and later FXSTS, FLSTS, FLSTC, FLSTF, FXDX, FXD and FXST model motorcycles. 38667-00 This kit fits 2000 and later FLTR, FLTRI, FLHT, FLHTC, FLHTCI, FLHTCUI, FLHR, FLHRI, FLHRCI and FLHP model motorcycles. 38672-01 This kit fits 2001 and later FXDWG2 model motorcycles. Kit Contents: QTY DESCRIPTION 1 O-ring, rubber 1 Cable, clutch 1 Pin, cable pivot 1 Grommet (Kit no. 38607-87A, 38660-00A and 38667-00 only) Installation NOTE A Service Manual for your motorcycle is available from your Harley-Davidson dealer. A SERVICE MANUAL IS NEEDED TO INSTALL THIS KIT. The rider’s safety depends upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have your Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. 1. Refer to the Service Manual for your motorcycle model. Screw the cable adjuster all the way in to allow for maximum cable free play. 2. Remove clutch hand lever from hand-lever bracket at pivot pin. Remove original clutch cable from hand lever and transmission. Retain anchor pin bushings. 3. See Figure 1. Install lever end of new clutch cable. Position cable eyelet in clutch lever slot. Retain with new cable pivot pin through original bushings. NOTE See Figure 2. When routing cable on models where clutch cable passes through inner fairing (FLHTC, FLHTC-U and FLHTP with fairing), clutch cable eyelet may be too large to pass through clutch cable access hole in fairing. If this is the case, use the template supplied with this sheet to file out a hole to accommodate the new eyelet. Place the grommet included with kit no. 38607-87A, 38660-00A, and 38667-00 in the hole after filing. 4. Secure the clutch lever in the lever bracket with the lever pivot pin and retaining ring. 5. Follow steps outlined in the applicable Service Manual and install the transmission-end of the new cable with O- ring. 6. Adjust clutch cable according to procedure in Service Manual.

Incoming search terms:

HARLEY DAVIDSON HEEL REST KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-04-2011

download
Models Kit 50227-01 is designed for forward controls and fits: •1989 and later FX Softail Models with Original Equipment (OE) Forward Controls, •1993 through 2002 FXDWG, •Dyna models equipped with Forward Control Kit 49080- 93 or 49080-93A. Kit 50227-01 does not fit Dyna models equipped with Forward Control Kit 49080-03 or Forward Control Footrest Support 33695-03 (left) or 33697-03 (right). Kit 50236-01 is designed for mid controls and fits: •all 1990 and later Dyna Model Motorcycles with Original Equipment (OE) Mid Controls. Additional Parts Required Proper installation of this kit also requires installing a pair of Heel Rest Pegs, or Shifter Pegs, which can also be mounted as heel rests. Refer to the appropriate Parts Catalog for stock shifter pegs, sold separately. The current Harley-Davidson Genuine Motor Accessories and Parts catalog also has a selection of Heel Rest Pegs or Shifter Pegs and matching Footpegs. Any shifter peg style that is symmetrical in design can be used as a left or right side heel rest. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE A Service Manual for your model motorcycle is available from a Harley-Davidson Dealer. Kit Contents See Figure 1 and Table 1. INSTALLATION NOTE See Figure 1 for the following procedure. 1. Remove the screw (B), lock nut (C) and spring washer (E) securing the left footpeg to the footrest support bracket (A). Save the hardware for later installation. NOTE Heel rest levers are side-specific. Levers mount so the set screws are on the underside. 2. Obtain a Heel Rest Peg or Shifter Peg (D) (purchased separately) and the left side heel rest lever (3). Apply Loctite® 243 (7) to the threads of the peg and install it to the left heel rest lever. 3. Obtain the screw (B), spring washer (E) and lock nut (C) removed in step 1, and the heel rest lever and peg assembly (D). Position the lever assembly to the desired angle on the mount, and slide the lever assembly with the spring washer into the footrest support bracket as shown. NOTE Splines on the lever and mount provide for a limited range of heel rest angle adjustment. For Kit 50227-01. The heel rest lever (3) can be adjusted after the mount (1) is attached but before the set screw (2) is installed. Slide the lever inward off the spline, and rotate it to the desired angle. For Kit 50236-01. The heel rest lever (3) angle cannot be adjusted after the mount (1) is attached without removing them from the footrest support bracket (A). Check to ensure the heel rest (D) is in a comfortable position before tightening the mounting hardware. 4. Install the original screw (B) and lock nut (C) to secure the heel rest assembly to the footpeg mount. Tighten to 33 ft- lbs (45.6 Nm). 5. Obtain a screw (6), spring washer (5) and nut (4) from the kit. Install the footpeg to the heel rest assembly and tighten to 33 ft-lbs (45.6 Nm). 6. Obtain a set screw (2) from the kit. Apply Loctite® 243 (7) to the threads, and install the set screw to the heel rest lever. Tighten to 16 in-lbs (1.8 Nm). 7. Perform Steps 1 through 6 for the right side. USE

Incoming search terms:

HARLEY DAVIDSON BLADE FRONT WHEEL KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-03-2011

download
INSTALLATION 1. Remove existing front wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to FRONT WHEEL in service manual. For FLSTC and FLSTN Models: Discard moon-style hub cap. or FXSTD: Discard tapered spacer. NOTE Install short valve stem (43157-83A) included in the installation kit. Discard all other valve stems. 2. See Figure 2. Install valve stem assembly (L) on wheel. Refer to TIRES in service manual. Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c) NOTES Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. The side with the machined groove on the hub face is the primary bearing side for all kits except Kits 41681-07 and 40818-08. For Kit 41681-07: Install the wheel so that the hub markings are on the left side and the machined groove is on the right side of the motorcycle. • For 2006 and later FXDWG Models: When correctly installed, the tire will be 0.08-0.2 in (2-5 mm) off of center, compared to the fender. • For 2007 and later FX Softail and 2008 and later FXDWG Models: The left side of the wheel is the primary bearing side. • For 2006 and earlier FX Softail and 2007 and earlier FXDWG Models: The right side of the wheel is the primary bearing side. For Kit 40818-08: • Proper installation of this kit requires the separate purchase of two floating brake discs (44343-01 for 2004 – 2007 models and 44553-06A (stock) or 41500012 (polished) for 2008 and later models) and a tire (43371-07 on 2004-2008 models and 44026-09A on 2009-later models). The left side of the wheel has machined DOT markings to identify it as the primary bearing side. • For 2008 and later Touring: Install bearing shim (43903- 08) under the primary bearing. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in service manual. 4. For FLSTC and FLSTN Models: Install wheel kit and right hand wheel spacer provided in installation kit. Refer to FRONT WHEEL in service manual. For FXSTD Models: Install wheel kit, stock wheel spacer and right side wheel spacer provided in installation kit in place of the tapered spacer discarded in Step 1. Refer to FRONT WHEEL in service manual. For FXSTS Models: Install wheel kit, stock wheel spacers and spacer provided in installation kit between the left side wheel spacer and the left fork. For all other models: Install previously removed wheel spacers. Refer to FRONT WHEEL in service manual. 5. Install front wheel (1), stock axle and stock axle nut. Refer to FRONT WHEEL in service manual. MAINTENANCE AND CLEANING Chrome parts must be maintained regularly to verify that they keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley-Davidson Wheel and Tire Cleaner, applied with Harley Wheel and Spoke Brush. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner. 3. After cleaning and polishing, seal the finish with a good quality sealer, such as Harley Glaze Polish and Sealant

HARLEY DAVIDSON DETACHABLE TOUR-PAK KIT FOR ELECTRA GLIDE CLASSIC INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
INSTALLATION Install Docking Kits and License Plate Holder 1. Install Rear Detachable Docking kit. Refer to the instruction sheet provided with kit. 2. Install Touring Detachable Tour-Pak Rack. Refer to the instruction sheet provided with kit. 1 4 2 3 is03989 1. License Plate Holder 2. Red Reflector 3. Original Equipment Screws 4. Original Equipment Bottom Support Tube Figure 2. Install License Plate Holder 3. See Figure 2. Install the new license plate holder (1) to the bottom support tube (4) using screws (3) saved from prior step. 4. Remove adhesive backing from red reflector (2) and carefully center and align it with the bottom edge of the license plate holder (1) and press firmly into place. -J03930 1 of 4 MOUNTING ANTENNA RELOCATION BRACKET 1. See Figure 6. Assemble joint assembly (9) to antenna mounting bracket (6) using lock washer (5) and 2 hex nuts (4). Tighten hardware securely. 2 1 5 4 3 is03992 1. Rear Docking Point 2. Docking Point Support Bracket 3. Antenna Mounting Bracket 4. Antenna/Cable Adapter 5. Rear Docking Point Screw and Locknut Figure 3. Relocated Antenna Bracket and Cable 2. See Figure 3. Install assembled antenna bracket (3) by removing screw and locknut (5) securing left rear docking point (1) to docking support (2). Install bracket as shown and reinstall rear docking point screw and locknut. Tighten screw and locknut to 15-19 ft-lbs (20.3-25.7 Nm) . 3. Thread antenna/cable adapter (4) onto joint assembly. ROUTING ANTENNA CABLES 1. See Figure 4. Gently remove left side cover (1) by pulling from frame tubes (no tools required). 2. Connect original antenna cable (not shown) to bottom of joint assembly. 3. Route antenna cable/wiring between left frame rail and fender. 4. See Figure 5. Attach cable to docking point support bracket in location (1) using short cable strap. 5. See Figure 4. Coil excess antenna cable/wiring (2) and use long cable strap (3) to fasten cable to frame under left side cover (1) with vehicle wiring harness. 6. See Figure 6. Cap unused wiring connector with connector housing (10).

Honda Motorcycle Na vigation Kit

0

Filed Under (Honda) by admin on 28-11-2010

download
Honda Motorcycle Na vigation Kit Honda Motorcycle Navigation Kit G e n e r i c A c c e s s o r i e s 2 0 0 8 For your peace of mind Honda Genuine Accessories are carefully designed, researched and stringently test ed tot he highest standards. And since they’re all Honda approved you’llknowthat they’rejustastoughand well made as your Honda motorcycle. Please Note -All prices quoted are correct at time of printing and are subject to change without prior notice. y e a r w a r r a n t y GENUINE ACCESSORIES Honda Motorcycle Navigation Kit Model Part Number Description RRP Remarks NAKED CBF 600 08A 40MER800B CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, £549.99 EARPHONE, MANUAL, MCC AR KIT, UN I TAT TACHM ENT KIT, BATTERY CBF 600 08A 40MER800A CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, £549.99 EARPHONE, MANUAL, MCC AR KIT, UN I TAT TACHM ENT KIT, BATTERY ON/OFF XL700V 08A 40MFF800 * CONTAINS NA VI GAT ION UNIT COMPONENT, £549.99 Must be combined with quartet harness CONTROLLER, EARPH ONE, MANUAL, 08A 30MFF800 MCCAR KIT, UNI TAT TACH ME NT KIT, BATTERY XL 1000V 08A 40MBT800 CONTAINSNAVI GAT ION UNIT COMPONENT, £549.99 Must be combined with quartet harness CONTROLLER, EAR PH ONE, MANUAL, 08A 30MBT800 MCCAR KIT, UNI TAT TACH ME NT KIT, BATTERY TOURERS/SPORT TOUR ERS DN-01 08A 40MEH800 CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, EARPHONE, £549.99 Must be combined with quartet harness MANUAL, MC CAR KIT, UNI TAT TACH MEN T KIT, AND BATTERY -CONTAINS 08A 30MEW800 ADDITIONALSTE ERIN G HANDLE C LAMPS FORV ISU AL INTE GRAT ION OF THE COMPONENT NT700V 08A 40MEW800 CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, EARPHONE, £549.99 Must be combined with quartet harness MANUAL, MC CAR KIT, UNI TAT TACH MEN T KIT, BATTERY

Incoming search terms:

HARLEY DAVIDSON ENGINE GUARD-MOUNTED FOG LAMP KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-02-2011

download
VRSC models: See Figure 3. Place the wire harness from the kit into the area in front of the battery. Do not block the air intake opening. All models except VRSC and 2004 and later XL models: See Figure 4. Install the wire harness from the kit. Place the relay in the opening of the frame under the seat area, and route the long leg of the harness forward along the frame backbone. 2004 and later XL models: See Figure 5. Remove the nuts retaining the ignition module (1) and temporarily reposition the module as shown. Place the relay in the recessed area (2) of the oil reservoir. Install the ignition module. Route the long leg of the harness along the frame backbone. CAUTION 1 WARNING -J02798 Figure 3. Install Fog Lamp Wiring Harness (VRSC Models) Place harness into this area but do not block air intake Air intake i04372 Battery Figure 4. Install Fog Lamp Wiring Harness (All Models Except VRSC. Dyna Model Shown) i02286.eps 1. Relay 2. Ground stud 3. Long leg of harness 2 1 3 2 of 6 Figure 2. Fog Lamp Wiring Harness Figure 1. Fog Lamp Schematic Ground To low beam To main circuit breaker Fuse N.O. Contact Switch Coil Fog lamp Fog lamp i01360a Relay 1. Fuse block 2. Relay 3. Connector to power 4. Ring terminals (Ground) 5. To fog lamps 6. Unterminated wire to low beam 7. Switch with boot and bracket 4 2 5 6 7 1 3 i05708 5. All 2003 and earlier models and VRSC: Cut the connector from the white power lead, and replace it with the ring terminal supplied in the kit. 6. All 2003 and earlier models, except VRSC: Connect the white wire with the ring terminal to the copper stud (BAT) terminal of the main circuit breaker. All 2004 and later models, except VRSC: Connect the white wire with connector to the B+ connector on the harness. All VRSC: Connect the white power lead to the battery positive terminal. 7. See Service Part illustration. Connect the black ground wires with the two ring terminals to the ground stud under the seat, or at any good electrical ground point. Secure the kit harness to the adjacent harnesses with cable straps (item 6) from the kit. When routing wires through the front fork, make sure the wires are clear of moving parts, to avoid pinching and possible short circuits. 8. Route the forward end of the harness past the steering head, and route the lamp switch leg of the harness along the left side of the handlebar to the clutch control. 9. See the Service Parts illustration. Obtain the switch mounting bracket (item 11) from the kit. Unscrew the boot from the lamp switch, and install the switch into the bracket. Replace the boot on the switch. NOTE If the boot becomes worn or damaged, or is lost, replace the boot to prevent moisture from entering the switch. See the Service Parts illustration (Item 12). 10. See Figure 6. Remove the lower screw (1) and washer from the clutch control clamp (3), and install the lamp switch and bracket assembly (2). Install the screw and washer and tighten to 60-80 in-lbs (7-9 Nm). 11. See the Service Parts illustration. Secure the lamp switch leg of the harness to the handlebar using the wire harness retainers already on the bike. Snap the retainers into the holes in the handlebar. 12. Remove the headlamp assembly. See HEADLAMP – REMOVAL instructions for the correct model in the Service Manual. CAUTION 3 of 6 -J02798 Figure 6. Install the Lamp Switch on the Clutch Control Clamp i04370 3 1 1. Lower clamp screw 2. Lamp switch and bracket assembly 3. Clutch control clamp 2 Figure 5. Install the Wiring Harness (2004 and Later Models) i05712 3

Incoming search terms: