thunderjet carb kit instructions

You search Auto repair manual PDF thunderjet carb kit instructions, if there are search results will appear below. If search results do not exist, please search by others keyword.



  thunderjet carb kit instructions Direct Download speed 5282 Kb/s

  thunderjet carb kit instructions Full Version speed 6162 Kb/s



KAWASAKI 1500 CARB THUNDER Air Filter Kit Installation And removal Instruction

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1) Remove Seat 10mm KAW 1500 CARB ADPTOR QTY PARTS LIST 1 1500 CARB ADAPTOR 1 3″ PIECE OF HOSE 1 DOUBLE BARB 1 L-BARB 1 3/8″ RED PLUG 1 ¼” BLACK VACCUM PLUG 1 M6-1 NYLON INSERT LOCK NUT 3 M6-1 X 16 FLAT SOCKET HD CAP SCREW 1 170 MJ 1 INSTRUCTIONS 2) Remove Dash Plaque 8mm bottom Bolt only 3) Lift from bottom then Remove speedo cable 4) Disconnect Electric Plugs 5) Remove 12mm bolts holding tank 6) Turn petcock OFF – Pinch off fuel line. 7) Disconnect the electric Plug under speedo opening 8) Lift Tank at Rear – Disconnect two Vent Lines; Fuel gage Vent will Pull up – Remove. 9) Remove Chrome Air Cover. 10) Left side Remove two screws – 10mm bolt in side Air box. Pull hoses off Remove 1″ hose going to cross over Tube. 11) Remove two 8mm bolts on Bracket – Remove Bracket 12) Remove Screw on Top of air Box Snorkel 13) Remove both side covers 14) Remove air Backing plate right side (Crank Case Breather hose that connects to stock air box will connect to new) 15) Remove Bracket that holds Carb and holds Backing Plate 16) Take idle adjustable Knob loose – let hang loose 17) Take Choke Knob out of holding Bracket 18) Hose that went to cross over tube MAY BE PLUGGED OR VENTED your Choice (Fresh air unit) ** 98′S or any models with carb warmer should disconnect carb warmer by pinching off line on each side of connector that plugs into carb on bottom. Small bracket with one screw directly on the bottom of carb. 19) Loosen Clamp that holds Carb to intake Manifold, Carb will hang loose 20) Remove intake Manifold 5mm Allen- Remove crossover tube. 21) (- BE CAREFULL-) LINE IT UP RIGHT- Replace intake Manifold (YOU MAY TO SEAL THIS WITH A SEALER LIKE PERMATEX) ( BE SUPER CAREFUL TO KEEP INTAKE COVERED DURING EACH STEP. SCREWS CAN FALL ONTO INTAKE) 22) Drain Float Bowl 3mm allen – very bottom of carb 23) Remove Float Bowl 4 screws (#2 Phillips) let hang down 24) Remove main jet, if Emulsion tube comes out use 8mm and Flat tip to separate jet from Emulsion tube. 25) Install with new jet 26) CAREFULLY Reinstall Float Bowl Cover 27) If installing Needle Remove Top Cover of Carb, Carefully pull the slide out. ( BE CAREFUL WITH DIAPHRAM) Remove Spring + Needle Install new Needle (WE RECOMMEND THE 3RD CLIP FROM TOP WITH TWO WASHERS ON TOP. REINSTALL 28) Be sure to reseat diaphragm – BE CAREFUL Reinstall Cover. 29) Install Carb to Intake – reconnect carb warmer if applicable 30) Reattach idle adjustment 31) Reattach Choke 32) Reattach Bracket in front of Carb- 33) Take Center bolt mount Rubber Gromlet from Stock Air box Plate install in to new Air box Adapter use stock Bolt, Attach to Bracke

Incoming search terms:

Honda Motorcycle Na vigation Kit

0

Filed Under (Honda) by admin on 28-11-2010

download
Honda Motorcycle Na vigation Kit Honda Motorcycle Navigation Kit G e n e r i c A c c e s s o r i e s 2 0 0 8 For your peace of mind Honda Genuine Accessories are carefully designed, researched and stringently test ed tot he highest standards. And since they’re all Honda approved you’llknowthat they’rejustastoughand well made as your Honda motorcycle. Please Note -All prices quoted are correct at time of printing and are subject to change without prior notice. y e a r w a r r a n t y GENUINE ACCESSORIES Honda Motorcycle Navigation Kit Model Part Number Description RRP Remarks NAKED CBF 600 08A 40MER800B CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, £549.99 EARPHONE, MANUAL, MCC AR KIT, UN I TAT TACHM ENT KIT, BATTERY CBF 600 08A 40MER800A CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, £549.99 EARPHONE, MANUAL, MCC AR KIT, UN I TAT TACHM ENT KIT, BATTERY ON/OFF XL700V 08A 40MFF800 * CONTAINS NA VI GAT ION UNIT COMPONENT, £549.99 Must be combined with quartet harness CONTROLLER, EARPH ONE, MANUAL, 08A 30MFF800 MCCAR KIT, UNI TAT TACH ME NT KIT, BATTERY XL 1000V 08A 40MBT800 CONTAINSNAVI GAT ION UNIT COMPONENT, £549.99 Must be combined with quartet harness CONTROLLER, EAR PH ONE, MANUAL, 08A 30MBT800 MCCAR KIT, UNI TAT TACH ME NT KIT, BATTERY TOURERS/SPORT TOUR ERS DN-01 08A 40MEH800 CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, EARPHONE, £549.99 Must be combined with quartet harness MANUAL, MC CAR KIT, UNI TAT TACH MEN T KIT, AND BATTERY -CONTAINS 08A 30MEW800 ADDITIONALSTE ERIN G HANDLE C LAMPS FORV ISU AL INTE GRAT ION OF THE COMPONENT NT700V 08A 40MEW800 CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, EARPHONE, £549.99 Must be combined with quartet harness MANUAL, MC CAR KIT, UNI TAT TACH MEN T KIT, BATTERY

Incoming search terms:

HW Prowler Carburetor Installation Instructions

0

Filed Under (Mikuni) by admin on 31-10-2010

download
1. Remove both seats and the plastic seat pans under the seats. 2. Remove the engine cover 3. Remove the air-box by removing the cross-bar support that runs under the air-box to the framing on each side by the seat framing and disconnect the air box from the carburetor and from the plastic intake in the rear. 4. Disconnect the engine breather hose from the bottom of the air box 5. Set the air-box to the side 6. Disconnect the plug going to the stock carburetor, this is the electronic choke. Wrap the end left on the vehicle with electrical tape. 7. Cut the fuel line just above the fitting on the passenger side of the carb 8. Remove the side cover off the drivers side of the carb where the throttle cable goes in, see fig. #1 9. Pull the throttle cable out and then remove the throttle cable end from the throttle plate See Fig. #2 10. Loosen the clamp on the rear of the carb holding the carb on 11. Pull the carb out of the intake boot 12. Set OE carb to the side. 13. Push the new Carb into the intake boot making sure the carb is perfectly vertical and then tighten the clamp back up. The new carb is slightly larger than the stock one so some additional pressure will be needed to get it in. 14. Route all the breather lines connected to the carb down under the carb. 15. Connect the throttle cable onto the new carb but putting the cable end in the bottom hole of the throttle plate on the passenger side of the carb allowing the cable to ride in the slot in the plate and then turn the throttle plate clock wise allowing the threaded end of the cable to fit into the lower round hole of the throttle cable connection plate. See Fig. #3 16. Make sure you have a nut on each side of the plate turn the nut on the outside of the plate to take up the slack in the throttle cable then tighten the nut on the inside of the plate. See Fig. #3 17. Push the fuel line onto the fuel inlet on the passenger side of the carb and install the supplied clamp to hold it on. The fuel line will be a little hard to push on. 18. DO NOT ATTEMPT TO INSTALL THE CHOKE CABLE PARTS SUPPLIED IN THE KIT UNTIL AFTER THE CHOKE CABLE ITSELF IS INSTALLED AND READY TO SCREW INTO THE CARBUETOR. 19. To install the supplied choke cable, drill a 3/8″ hole in the dash on the left side of the steering wheel in a location convenient to your left hand. 20. Remove the plastic nut from the bottom of the choke handle on the choke cable. 21. Push the choke cable thru the hole you drilled and then slide the nut over the cable to the inside of the dash and reinstall back on the back of the choke mechanism. Some dash screws maybe needed to be removed to accomplish this

HARLEY DAVIDSON CLUTCH CABLE ASSEMBLY INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-03-2011

download
36753-87A This kit fits 1987 and later FXLR model motorcycles. 36755-87A This kit fits 1987 and later FXRS/SP model motorcycles. 38601-89 This kit fits 1988 and later FLTC, FLTC-Ultra, FLHS, FLHTC FLHTC-Ultra and FLHTP model motorcycles. 38606-87A This kit fits 1987 and later FXR, FXRS and FXRT model motorcycles. 38607-87A This kit fits 1987 and later FLST, FXST, FXSTC, FXRP, FLTC, FLHT, FLHTP and FLHTC model motorcycles. 38617-95 This kit fits 1995 and later FXSTSB model motorcycles. 38647-98 This kit fits 1998 and 1999 FXSTB model motorcycles. 38661-00 This kit fits2000 and later FXDL, FXDS-CONV and FXDWG model motorcycles. 38664-00 This kit fits2000 and later FXSTD model motorcycles. 38665-00 This kit fits2000 and later FXSTB model motorcycles. 38666-00 This kit fits2000 and later FXSTS, FLSTS, FLSTC, FLSTF, FXDX, FXD and FXST model motorcycles. 38667-00 This kit fits 2000 and later FLTR, FLTRI, FLHT, FLHTC, FLHTCI, FLHTCUI, FLHR, FLHRI, FLHRCI and FLHP model motorcycles. 38672-01 This kit fits 2001 and later FXDWG2 model motorcycles. Kit Contents: QTY DESCRIPTION 1 O-ring, rubber 1 Cable, clutch 1 Pin, cable pivot 1 Grommet (Kit no. 38607-87A, 38660-00A and 38667-00 only) Installation NOTE A Service Manual for your motorcycle is available from your Harley-Davidson dealer. A SERVICE MANUAL IS NEEDED TO INSTALL THIS KIT. The rider’s safety depends upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have your Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. 1. Refer to the Service Manual for your motorcycle model. Screw the cable adjuster all the way in to allow for maximum cable free play. 2. Remove clutch hand lever from hand-lever bracket at pivot pin. Remove original clutch cable from hand lever and transmission. Retain anchor pin bushings. 3. See Figure 1. Install lever end of new clutch cable. Position cable eyelet in clutch lever slot. Retain with new cable pivot pin through original bushings. NOTE See Figure 2. When routing cable on models where clutch cable passes through inner fairing (FLHTC, FLHTC-U and FLHTP with fairing), clutch cable eyelet may be too large to pass through clutch cable access hole in fairing. If this is the case, use the template supplied with this sheet to file out a hole to accommodate the new eyelet. Place the grommet included with kit no. 38607-87A, 38660-00A, and 38667-00 in the hole after filing. 4. Secure the clutch lever in the lever bracket with the lever pivot pin and retaining ring. 5. Follow steps outlined in the applicable Service Manual and install the transmission-end of the new cable with O- ring. 6. Adjust clutch cable according to procedure in Service Manual.

Incoming search terms:

HARLEY DAVIDSON SKULL FOOT BOARD INSERT KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2011

download
Kit 50704-04 is an Operator Footboard Insert Kit. •This kit fits all 2004 and later FLHRS/I (Road King® Custom) model motorcycles. •This kitalso fits 1986 and later FLHR/I/CI, FLHT/C/CI/CUI and FLTR/I models equipped with Swept-Wing footboard pans 50683-04 (right) and 50688-04 (left) . Kit 50704-04 contains the following items: QTY DESCRIPTION PART NO. 1Operator footboard insert (right) 50705-04 1Operator footboard insert (left) 50706-04 Kit 50707-04 is a Passenger Footboard Insert Kit. •This kitfits 2004 FLHTCSE models, and all 1986 and later Touring model motorcycles equipped with Swept- Wing Grooved Passenger Footboard Kit 50357-04 . Kit 50707-04 contains the following items: QTY DESCRIPTION PART NO. 1 Passenger footboard insert (right) 50708-04 1 Passenger footboard insert (left) 50709-04 Kit 50710-04 is an Operator Footboard Insert Kit. •This kitfits all 1980 and later Touring models except FLHRS, and 1986 and later FL Softail®model motorcy- cles equipped with footboard pans 50621-79A. Kit 50710-04 contains the following items: QTY DESCRIPTION PART NO. 1Operator footboard insert (right) 50711-04 1Operator footboard insert (left) 50712-04 Kit 50713-04 is a Passenger Footboard Insert Kit. •This kit fits all 1986 and later Touring models . •This kit also fits 1986 and later FL Softail models when equipped with accessory passenger footboard kits (Part Number 50602-89B, 50955-97A, 50955-00 or 50602-00). • This kit iscompatible with Chrome Passenger Footboard Cover Kits (Part Numbers 50782-91, 50193-96, 50194-96 and 50246-00). • This kit is notcompatible with Leather Passenger Footboard Fringe Kits (Part Numbers 50947-98 or 50956-98). Kit 50713-04 contains the following items: QTY DESCRIPTION PART NO. 1 Passenger footboard insert (right) 50714-04 1 Passenger footboard insert (left) 50715-04 Installation, Kit 50704-04 (For Swept-Wing Operator Footboards): Removing Previously Installed Inserts 1. Apply liquid dishwashing soap to the rubber beads protruding through the bottom of the footboard pan. 2. With the operator footboard in the “up” position, use a screwdriver to work the rubber footboard beads out through the top of the footboard. 3. Repeat the above steps for the remaining footboard insert. Installing the New Inserts 4. Apply liquid dishwashing soap to the rubber beads on the new footboard insert. 5. Place the footboard insert into position on the footboard pan. From the underside of the footboard, use a pliers to pull each rubber bead into its mating hole in the footboard pan until the beads protrude through the pan. 6. Repeat the above steps for the remaining footboard insert.

Daytona 675 Motorcycle Race Kit Installation Manual

0

Filed Under (Triumph) by admin on 29-10-2010

download
Remove the existing cylinder head gasket in line with the procedures detailed in the Daytona 675 service manual. 2. Fit the chosen race kit cylinder head gasket following the procedures detailed in the Daytona 675 service manual. Caution The use of the following race kit cylinder head gaskets will require changes to the fuelling settings. To alter fuelling settings a third party programmable control unit will be required. Item Description Qty 1 Head gasket (t = 0.65mm) 1 1 Head gasket (t = 0.60mm) 1 1 * Page 7 of 29 © Triumph Designs Ltd 2007. Cams, Valve Spring & Sprocket Kits Parts Supplied Camshaft Inlet Kit – A9618055 Camshaft Exhaust Kit – A9618056 Valve Spring Kit – A9618058 Camshaft Sprocket Kit – A9618057 Warning The race kit must be fitted as a complete set. If it is not fitted as a complete set a failure may result which could cause loss of motorcycle control and an accident. Caution The use of the Camshaft, Valve spring & Sprocket race kits detailed below will require changes to the fuelling settings. To alter fuelling settings a third party programmable control unit will be required. 5 5 4 1 3 2 4 3 Item Description Qty 1 Cam assy, inlet, race 1 Item Description Qty 2 Cam assy, exhaust, race 1 Item Description Qty 3 Valve spring, 14.4id, race12 Item Description Qty 4 Sprocket, camshaft, 34T 2 5 Socket head cap screw, Encapsulated, M6x10 4
Page 8 of 29 © Triumph Designs Ltd 2007. NOTE •The standard inlet cam is 9.25mm max lift and 258.50o duration. The race kit inlet cam is 9.25mm max lift and 268.74o duration. •The standard exhaust cam is 8.5mm max lift and 246o duration. The race kit exhaust cam is 8.5mm max lift and 262.21o duration. •The race kit valve spring must be used in conjunction with the standard spring platforms and retainers. The fitted length of the race springs is the same as the standard spring. 1. The race kit valve springs should be assembled in the same manner as the standard valve springs. Follow the procedure detailed in section 3 of the Daytona 675 service manual. Ensure the springs are installed with the close wound, colour coded end of the springs facing downwards, towards the piston. 2. The race kit camshafts should be assembled in the same manner as the standard camshafts. Follow the procedure detailed in section 3 of the Daytona 675 service manual. 3. The race kit cam sprockets should be mounted and secured to the camshafts using the slotted holes in the sprocket. The slotted holes allow adjustment of the valve timing. The circular holes in the sprockets are for Triumph service tool T3880102 and should not be used to mount the sprockets to the camshafts. NOTE •No timing marks are included on the race sprockets. Race engines will typically have different depths skimmed off the cylinder head and, therefore require specific individual timing. 4. The camshafts should be timed using cam degreeing equipment which typically consists of a degree wheel, pointer, dial indicator and piston stop. Optimum cam timing will depend on the exact specification of the engine, but a recommended starting point is 104o IMOP (Inlet Maximum Opening Point) and 104o EMOP (Exhaust Maximum Opening Point). 5. Always check the inlet and exhaust piston to valve clearance for the timing selected to use, before running the engine. You must ensure both clearances are adequate. As a guide, the standard nominal piston to valve clearance is 1.3mm inlet & 1.5mm exhaust

Incoming search terms:

HARLEY DAVIDSON HEEL REST KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-04-2011

download
Models Kit 50227-01 is designed for forward controls and fits: •1989 and later FX Softail Models with Original Equipment (OE) Forward Controls, •1993 through 2002 FXDWG, •Dyna models equipped with Forward Control Kit 49080- 93 or 49080-93A. Kit 50227-01 does not fit Dyna models equipped with Forward Control Kit 49080-03 or Forward Control Footrest Support 33695-03 (left) or 33697-03 (right). Kit 50236-01 is designed for mid controls and fits: •all 1990 and later Dyna Model Motorcycles with Original Equipment (OE) Mid Controls. Additional Parts Required Proper installation of this kit also requires installing a pair of Heel Rest Pegs, or Shifter Pegs, which can also be mounted as heel rests. Refer to the appropriate Parts Catalog for stock shifter pegs, sold separately. The current Harley-Davidson Genuine Motor Accessories and Parts catalog also has a selection of Heel Rest Pegs or Shifter Pegs and matching Footpegs. Any shifter peg style that is symmetrical in design can be used as a left or right side heel rest. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE A Service Manual for your model motorcycle is available from a Harley-Davidson Dealer. Kit Contents See Figure 1 and Table 1. INSTALLATION NOTE See Figure 1 for the following procedure. 1. Remove the screw (B), lock nut (C) and spring washer (E) securing the left footpeg to the footrest support bracket (A). Save the hardware for later installation. NOTE Heel rest levers are side-specific. Levers mount so the set screws are on the underside. 2. Obtain a Heel Rest Peg or Shifter Peg (D) (purchased separately) and the left side heel rest lever (3). Apply Loctite® 243 (7) to the threads of the peg and install it to the left heel rest lever. 3. Obtain the screw (B), spring washer (E) and lock nut (C) removed in step 1, and the heel rest lever and peg assembly (D). Position the lever assembly to the desired angle on the mount, and slide the lever assembly with the spring washer into the footrest support bracket as shown. NOTE Splines on the lever and mount provide for a limited range of heel rest angle adjustment. For Kit 50227-01. The heel rest lever (3) can be adjusted after the mount (1) is attached but before the set screw (2) is installed. Slide the lever inward off the spline, and rotate it to the desired angle. For Kit 50236-01. The heel rest lever (3) angle cannot be adjusted after the mount (1) is attached without removing them from the footrest support bracket (A). Check to ensure the heel rest (D) is in a comfortable position before tightening the mounting hardware. 4. Install the original screw (B) and lock nut (C) to secure the heel rest assembly to the footpeg mount. Tighten to 33 ft- lbs (45.6 Nm). 5. Obtain a screw (6), spring washer (5) and nut (4) from the kit. Install the footpeg to the heel rest assembly and tighten to 33 ft-lbs (45.6 Nm). 6. Obtain a set screw (2) from the kit. Apply Loctite® 243 (7) to the threads, and install the set screw to the heel rest lever. Tighten to 16 in-lbs (1.8 Nm). 7. Perform Steps 1 through 6 for the right side. USE

Incoming search terms:

240 Sport Bike Swingarm Installation Instructions

0

Filed Under (Tips and Review) by admin on 02-12-2010

download
Motorcycles can be dangerous if not properly maintained and ridden safely. RC Components has no control over the usage of any of its parts. RC Components expects its customers to exercise good judgment as to the proper selection, installation, use, and maintenance of any parts. RC Components assumes no responsibility for damage or injury of any kind because of the misuse or improper application of any parts in any way by any person. RC Components expects the end user to exercise good judgment. • Before installing this kit, read through these directions completely. This will familiarize you with the way in which the parts fit together and the tools needed to complete the job. • Before performing any installation steps, disconnect the motorcycle’s battery to eliminate any possibility of electrical damage or personal injury due to a short circuit. Part Number: NSTSB240 Page 2 of 12 Materials Needed: • Hardware Kit. Kit includes (See picture below): 04-05 GSXR750-600 & 03-04 GSXR1000 Kit Inboard Brake Kit Part Number: INSTSB240 Page 3 of 12 04-05 GSXR750-600 & 03-04 GSXR1000 Kit for Stock Caliper 08 Busa Kit for Inboard Brake Part Number: INSTSB240 Page 4 of 12 05-06 GSXR 1000 Kit for Inboard Brake
Part Number: INSTSB240 Page 5 of 12 05-06 GSXR1000 Kit for Stock Caliper 99-07 Busa Kit for Inboard Brake
Part Number: INSTSB240 Page 6 of 12 99-07 Busa Kit for Stock Caliper Tools Needed: • Bike Specific Service Manual (Refer to manual for all torque specs and tools that are not specified by RC Components.) • Assorted hand tools, metric and standard sockets and wrenches. • Hoist or other means to lift bike. • Torque wrench • Loctite, and anti-seize • Chain breaker • Bike specific sockets are required for some bikes. (Refer to factory service manual). • Die grinder (for chain to frame clearance on some models) Installation Instructions 1.) Stock Component Removal To begin installing this kit it is necessary to raise the rear end of the bike using a suitable hoist. Be sure to keep the bike centered on the front wheel to keep the bike from tipping over. Once you have the bike lifted and properly secured, begin with the removal of the following stock components ( For detailed information on the removal of these parts, please consult your factory manual) : 1.) Muffler or mufflers 2.) Left side and lower body panels 3.) Voltage regulator (08 model only) 4.) Front sprocket cover 5.) Front sprocket 6.) Chain

HARLEY DAVIDSON HYBRID CAM PLATE AND HIGH FLOW OIL PUMP KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the service manual and follow the instructions to remove the seat and disconnect the battery cables, negative (-) cable first. Retain all seat mounting hardware. Gasoline can drain from the carburetor fuel line when disconnected from fuel valve fitting. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. Wipe up spilled fuel immediately and dispose of rags in a suitable manner. (00256a) NOTES Installing this kit requires removal and installation of the cam support plate. Refer to the service manual for instructions with the following exception pertaining to cam compartment compo- nents: The crank and primary cam sprocket flange bolts are specially hardened, and the flat washers are of a special diameter and have ground surfaces. Use ONLY the parts provided in the Drive Gear Retention Kit (H-D Part Number 25533-99A, sold separately) when installing this kit. -J04804 1 of 7
The cr ank sprocket flange bolts and pr imary cam sproc ket flange bolts ARE NOT interchangeable. 2. Refer to the service manual to remove and discard the crank sprocket flange bolts and primary cam sprocket flange bolts and washers. 3. For 1999 models only: Refer to the service manual to remove and discard the currently installed cam drive sprocket. 4. Refer to the service manual to remove and disassemble the cams from the support plate and oil pump. Discard the support plate and oil pump. 5. For 1999 – 2000 Dyna, 2000 Softail, 1999 – 2000 Touring, and 2001 EFI Touring models only: Inspect the cams, chain, sprockets and chain tensioners for wear, and replace as needed. Refer to the service manual for inspection and replacement procedures. For 2001 – 2005 Dyna, 2001 – 2006 Softail, 2002 – 2006 Touring, and 2001 carbureted Touring models only: Inspect the cams and secondary cam chain for wear, and replace as needed. Refer to the service manual for inspection and replacement procedures. The primary cam chain, primary sprockets and both tensioners will be replaced by new components from the kit. For ALL models and years: Discard the guide, as it will not be used. INSTALLATION 1. ALL models: See Figure 1. Obtain the new Rear Cam Roller Bearing Kit (H-D Part Number 8983) from inside the Cam Service Kit (H-D Part Number 17045-99C, purchased separately), and install as indicated in Step 2. NOTE See Figure 2. If not enough of the splined shaft is exposed to install the sprocket, omit the spacer (4) and proceed to Step 2e. When the bearing inner race is started onto the machined area, remove the flange bolt (5), flat washer (6) and sprocket, then assemble using the spacer (4). Repeat Step 2e to fully install bearing inner race. To center thrust washer, be sure o-ring is installed in relief groove. Damage to bearing cage and engine can occur if thrust washer is not centered. (00473b) 2. See Figure 1. Install the O-ring (5), thrust washer (4) and bearing inner race (3) onto the rear camshaft as follows: a. See Figure 2. To properly locate the thrust washer (2), install the O-ring (3) in the grinding relief groove on the splined end of the rear camshaft between the machined area and the secondary cam sprocket.

Incoming search terms:

HARLEY DAVIDSON ADVANCED AUDIO COMMUNICATION SWITCH KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1. Refer to the Service Manual and follow the instructions given to remove the Maxi® Fuse. 2. Refer to the instructions included with the Advanced Audio Hands Free Phone Interface, CB Radio or Intercom Kit, and proceed with that installation until the installation of the items in this kit is called for. 3. Remove the outer fairing and windshield. Refer to OUTER FAIRING/ WINDSHIELD REMOVAL in the Service Manual. 4. On the fairing cap, remove the inner left side hole plug. See Figure 1 and the FAIRING CAP SWITCHES (FLHTC/U) section in the Service Manual. Install the fairing speaker switch (4) in the opening as follows: If a cruise control switch IS present: Follow the instructions in the Service Manual to install the speaker switch. If a cruise control switch IS NOT present: a. Obtain the speaker switch adapter wire (5) from the kit, and the butt splice connector included with the speaker switch. b. Refer to SEALED BUTT SPLICE CONNECTORS in the Service Manual. Splice the adapter wire to the black/ green speaker switch lead. c. Insert the terminated end of the adapter wire into cavity 12 of the fairing cap switch connector [105B] 5. Remove the original equipment left-hand control switch assembly per the HANDLEBAR SWITCHES, REMOVAL, LEFT HANDLEBAR CONTROLS instructions in the Service Manual. 6. Install the new left-hand control switch assembly (3) from the kit. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 7. ALL models: Install the console pod assembly (1), and route the harness forward into the fairing per the instructions packaged with the Advanced Audio Hands Free Phone Interface, CB Radio or Intercom Kit. Be sure that steering is smooth and free without interference. Interference with steering could result in loss of vehicle control and death or serious injury. (00371a) • Be sure the wires do not pull tight when handlebars are turned fully to left or right fork stops. 8. Unless already installed, install the overlay harness per the instructions packaged with the Hands Free Phone Interface, CB Radio or Intercom Kit. 9. Refer to the Service Manual and follow the instructions given to re-install the Maxi Fuse

Incoming search terms: