scematic drawing of harley davidson 1989 fxrs swingarm pivot bolt and spacer setup

You search Auto repair manual PDF scematic drawing of harley davidson 1989 fxrs swingarm pivot bolt and spacer setup, if there are search results will appear below. If search results do not exist, please search by others keyword.



  scematic drawing of harley davidson 1989 fxrs swingarm pivot bolt and spacer setup Direct Download speed 5282 Kb/s

  scematic drawing of harley davidson 1989 fxrs swingarm pivot bolt and spacer setup Full Version speed 6162 Kb/s



HARLEY DAVIDSON PIVOT BOLT COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 22-02-2011

download
This kit fits all 2004 and later XL (Sportster®) model motorcycles INSTALLATION Right-Side Pivot Bolt Cover Installation Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) 1. See Figure 1. Start a set screw (2) from the kit into one of the pivot bolt covers (1) about two or three turns. 2. Note the position of the bottom-most flat on the rear-fork pivot hex-head bolt (3). Line up the pivot bolt cover over the bolt head so the set screw is centered on the hex flat. Use the 3/32 inch hex key from the kit to tighten the set screw securely to the head of the rear-fork pivot bolt. 3. Make sure the pivot bolt cover is clean and free of any oil or grease. Remove the protective backing from the adhesive disk on the back of the decorative insert (9). Install the decorative insert onto the end of the pivot bolt cover with the image or text upright and parallel to the ground. Press the insert firmly against the end of the pivot bolt cover and hold pressure for 30 seconds. After releasing pressure, avoid direct contact with the insert for about 20 minutes. Left-Side Pivot Bolt Cover Installation 4. Models without passenger footrests: Use an 8 mm hex key to remove the bolt (5) retaining the double-tube clamp (4). Models with passenger footrests: Use an 8 mm hex key to remove the two bolts (5) and the left-side passenger footrest and bracket assembly (6). 5. Start a set screw (2) from the kit into one of the pivot bolt covers (1) about two or three turns

HARLEY DAVIDSON Softail Big Shots Staggered Exhaust System Installation Manual

0

Filed Under (Harley Davidson) by admin on 20-12-2010

download
STOCK EXHAUST SYSTEM REMOVAL 1. If equipped, loosen the floor boards to gain clearance for exhaust removal and installation. 2. Loosen heat shield clamps on both the front and rear head pipes. 3. If equipped, loosen crossover pipe clamp, located between front and rear head pipes. 4. Remove two cylinder exhaust port flange nuts from each head pipe, located at the cylinder head. 5. Remove the bolts that attach mufflers to the frame. 6. Remove the complete exhaust system and set aside. Assistance may be required. 7. Remove stock mounting bars and brackets. 8. On models equipped with upper mounting bar attached at swing arm pivot bolt, go to step 9. If upper mounting bar is attached with two torx bolts (not swing arm bolt) go to step 10. 9. Remove right side 1/4″-20 bolt which holds lower fender in place. The fender will flex outwards allowing removal of right passenger foot peg bolt. Park the motorcycle on its side stand. Position a floor jack under right hand frame tube of the motorcycle below swing arm pivot bolt. Raise jack just enough to take the weight off swing arm pivot bolt. Remove swing arm pivot bolt and stock upper mounting bar. Replace swing arm pivot bolt and torque to 120 ft. lbs. Reinstall passenger foot peg using 1/2″-20 x 3″ bolt and 1 5/8″ long spacer (supplied). Reinstall 1/4″-20 fender bolt. 10. Using a T50 torx driver, remove the three mounting bolts and mounting bar. (Two of the bolts are visible, the third also attaches right hand passenger foot peg pivot and is accessed by removing foot peg. Reinstall foot peg using 3/8″x 2-1/2″ Allen bolt and 3/4″ long spacer (supplied). 11. Carefully remove exhaust port flanges and circlips from the stock exhaust system using snapring pliers. NOTE: Replace bent or damaged circlips. Check exhaust port gasket condition. (Recommended replacement exhaust port gaskets, Harley part number:17048-98 or 65324-83A)

Incoming search terms:

Ducati Sport Clutch Lever INSTALLATION INSTRUCTIONS

0

Filed Under (Ducati) by admin on 26-10-2010

download
1 To remove your stock lever, use a 19mm wrench or (adjustable wrench) to remove the large sheet metal nut attached to the main pivot bolt that holds the lever. (Photo 1a) Once the locknut is removed, push the main pivot bolt out with your finger or if necessary tap lightly with a rubber mallet or plastic handle end of a screwdriver (Photo 1b) After the pivot bolt is removed, the lever will detach from the master cylinder. (Photo 1c) 1a See other side for further instructions INSTALLATION INSTRUCTIONS FOR PART # CRC552 ® C/5 Sport Clutch Lever Part # CRC552 1b 1c INSTRUCTIONS_CRC552 12/27/07 10:05 AM 23 4 2 Included with your ASV lever is a plastic bag that contains a custom pivot bolt, spacer & locknut. These parts will replace the OEM Brembo parts that were used with your stock lever. 3 Carefully place the lever into the master cylinder while aligning the plunger rod into the plunger cup on your ASV lever as shown in photo 3. 4 Align the lever and the master cylinder pivot bolt holes and Install the main pivot bolt, you will need to pre-load the lever into the master cylinder to get the bolt through the holes. The bolt head has two cut outs on the sides that need to be aligned with the matching area on the master cylinder. Be sure the head of the bolt seats down into the slotted area of the master cylinder. It may be necessary to use a rubber mallet or Plastic end of a screwdriver (Photo 4) to tap the head of the bolt down into its slot. 5 On the other side of the pivot bolt where the threads are, you will see that there is space around the pivot bolt. You will need to install the aluminum spacer that was supplied in the plastic bag with the pivot bolt and locknut. The spacer has a small flange on one side. The flange should be on the outer side when installing it into the hole surrounding the bolt. (Photo 5a) You may need to use pressure to seat the spacer fully into the hole surrounding the pivot bolt. You should be able to do this by using your fingers or thumbs as shown in photo 5b.

HARLEY DAVIDSON REAR SWINGARM AXLE COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
INSTALLATION Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) NOTE XL Sportster 883 and XL1200R models may require loosening or removal of the rear muffler in order to install the right side rear axle cover. See the EXHAUST SYSTEM REMOVAL section of the Service Manual. 1. Support the vehicle, and loosen or remove the rear muffler if necessary. XL Sportster 883 and XL1200R models: Remove the right-side lower shock absorber mounting bolt. Save for re-installation. All other models: Remove and discard the right-side lower shock absorber mounting bolt. 2. Swing the bottom of the shock absorber out of the way. Position the right-side swingarm axle cover (2) over the swingarm and behind the shock absorber. 3. Reposition the shock absorber. XL Sportster 883 and XL1200R models: Install the shock absorber mounting bolt removed in Step 1. All other models: Install the shoulder bolt (3) from the kit. All models: Tighten the bolt to 45-50 ft-lbs (61-68 Nm) . NOTE When torquing the bolt, align two of the bolt-head flats parallel to the ground. This will allow proper orientation of the bar and shield logo on the bolt cover. 4. Position the bolt cover (4) over the bolt head (3) with the Bar-and-Shield logo oriented upright, and lock in place with the set screw (5). Tighten securely. Reposition and tighten the muffler per the Service Manual instructions. 5. Remove and discard the left-side lower shock absorber mounting bolt. Move the bottom of the shock absorber out of the way. Position the left-side swingarm axle cover (2) over the swingarm and behind the shock absorber. 6. Reposition the shock absorber and install the shoulder bolt from the kit. Tighten to 45-50 ft-lbs (61-68 Nm) , aligning two of the bolt head flats parallel to the ground. 7. Position the bolt cover over the bolt head with the Bar-and- Shield logo oriented upright, and lock in place with the set screw. Tighten securely

HARLEY DAVIDSON SOFTAIL SWINGARM PIVOT COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-04-2011

download
INSTALLATION 1. Use rubbing alcohol to clean the swingarm surface, pivot bolt, and nut. 2. Place the larger left-side pivot cover (3) over the pivot nut. Position the set screw (4) at the bottom of the cover. Tighten set screw to 16 in-lbs (1.8 Nm) . 3. Remove adhesive backing from and apply the left-side trimplate to the swingarm. Apply pressure to the trimplate on the swingarm for one minute. 4. Remove adhesive backing from and apply an emblem to the center of the pivot cover. Apply pressure to the emblem for one minute. 5. Repeat Steps 1-4 for the right side of the swingarm. 6. Allow adhesive to cure for 24 hours before operating the vehicle. SERVICE PARTS 4 2 5 3 1 5 6 3 is01811 Figure 1. Service Parts: Swingarm Pivot Cover Kit Table 1. Service Parts: Swingarm Pivot Cover Kit Part Number Description (Quantity) Item Not Sold Separately Right-side trimplate and adhe- sive 1 Not Sold Separately Left-side trimplate and adhesive 2 Not Sold Separately Adhesive emblem (2) 3 Not Sold Separately Left-side pivot cover 4 3231B Set screw (2) 5 Not Sold Separately

HARLEY DAVIDSON SOFTAIL Shortshot Exhaust System REMOVAL AND INSTALLATION

0

Filed Under (Harley Davidson) by admin on 17-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. On FLSTC, FLSTF, FLSTN and FXSTS loosen the right hand floor board mounting bolts to gain clearance for exhaust removal and installation. 2. Loosen the heatshield clamps on both front and rear exhaust pipes. 3. Loosen the crossover pipe clamp, located between the front and rear head pipe. (This step is not necessary on 2000 models). 4. Remove the two mounting nuts from each head pipe, located at the cylinder head. 5. Remove the bolts that attach the mufflers to the frame. 6. Remove the entire exhaust system and set it aside. 7. On pre 2000 models remove the lower mounting bar. 8. FLSTN, FLSTF and FXSTD models have an upper mounting bar that must be removed in addition to the lower bar. 9. Park the motorcycle on its side stand. Remove the right side 1/4″-20 bolt which holds the lower fender in place. The fender will flex out of the way allowing the removal of the right passenger foot peg bolt. Position a floor jack under the right hand frame tube of the motorcycle below the swing arm pivot bolt. Raise the jack just enough to take the weight off the pivot bolt and remove the bolt and stock mounting bar. Set the mounting bar aside. Replace the pivot bolt and torque it between 120 -150 ft. lbs. Reinstall the passenger foot peg using the 1/2″-20 x 3″ bolt and an 1 5/8″ long spacer (supplied). 10. On 2000 year models, using a #50 Torx driver, remove the three mounting bolts, and set the mounting bar aside. (Two of the bolts are visible, the third is accessed by removing the right hand passenger foot peg.) Replace the foot peg using the 3/8″-16 x 2 1/2″ bolt and 3/4″ length spacer (supplied). 11. Carefully remove the flanges and circlips from the stock exhaust system using snapring pliers. NOTE: If circlips look bent or twisted replace them with new circlips. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Vance and Hines recommends you replace your exhaust gaskets with Sceamin’ Eagle gaskets part number 17048-98. 2. Install the mounting bracket to the frame, by aligning the two 3/8″ holes in the bracket with the two holes in the frame below the right rear footrest, using the two 3/8″-16 x 3/4″ flange head bolts (supplied), do not tighten at this time. When the bracket is mounting correctly, it should bend out and away from the motorcycle, with the four holes of the bracket toward the front of the motorcycle. 3. Install the circlips and flanges from the stock system on to both of the new head pipes

HARLEY DAVIDSON CHROME FOOTPEG BOLT KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 04-04-2011

download
The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE The bolts supplied in this kit are designed for a one-time installation only. If this kit is removed after initial installation, you must re-apply Loctite 243 (Blue) to the threads of the bolts. Kit Contents 3 1 3 is05122a Figure 1. Service Parts: Chrome Footpeg Bolt Kit Table 1. Service Parts Part Number Description (Quantity) Item 94128-01 Washer, chrome (2) 1 8023 Nut, chrome (2) 2 4233 Screw, TORX®, button head, chrome (2) 3 INSTALLATION 1. Remove existing nut and bolt securing footpeg to mount. Discard nut and bolt. 2. See Figure 2. Install chrome washer to bolt, then install bolt through mount and footpeg as shown. 3. Install nut to bolt. Tighten hardware to 10-16 ft-lbs (13.6- 21.7 Nm) . 4. Repeat Steps 1 through 3 for the opposite side

Harley Davidson Road Rod Saddle Bag System Kit INSTALLATION Instructions

0

Filed Under (Harley Davidson) by admin on 16-04-2012

download
Use locktite on all fasteners!! 2. Put bike on lift and place jack under frame. Raise bike to lift rear wheel. 3. If swing arm pivot shaft is drilled and tapped on each end, they need to be redrilled and tapped to 3/8-16 to a depth of _” deep. If you are unable to drill & tap your swing arm pivot shaft, you can purchase one from Cycle Visions (part #CV6121), See Harley Davidson® V-Rod® Service Manual Section 2, Page 2.89 for removal and installation instructions. 4. Remove seat, passenger seat, turn signal module, rear fender cover, turn signal license plate assembly, and rear foot peg assemblies. NOTE: Our bag system will not work with stock exhaust system… we recommend the 2-into-1 Supertrap, or you may use any exhaust system that is lower than the rear axle bolt. 5. Remove the two upper shock bolts. Relocate the shock spacer from the right side to the left side, and use the new spacer supplied on the right side. 6. Install front bag mount between frame and spacer (see Figure 1), reinstall shock bolts and torque to 31-50 lbs. 7. Install lower bag support frame to swing arm pivot shaft using the 3/8″ bolt through rear foot peg clevis and cover (see in Figure 2). NOTE: There is a right and left covers and bag support, install accordingly. Torque to 35 foot lbs. 8. Install rear fender front mounting tabs using 8mm 1.25 x _ and flat washers (supplied in kit) (see Figure 3). 9. Install upright saddlebag support brackets to the lower bag mount assembly and lower fender extension crossover mount. (see Figure 4). Torque to 25 lbs. NOTE: Install crossover mount with gusset facing down. 10. Remove license plate light from your rear turn signal bracket license plate assembly. Install license plate light on our license plate light bracket (see Figure 5). 11. Install the license plate bracket on the inside of the rear fender extension using the top holes of the license plate frame (see Figure 6 & 7). 12. Install fender washers on the inside of the fender extension (see Figure 8). 13. Install upper fender bracket to rear fender extension with a _-20 bolt supplied in kit (see Figure 9). 14. Install rear fender extension with chrome button fitted bolts. (see Figure 10 & 11). 15. To check alignment and fit of rear fender extension reinstall original rear fender. Once you have everything lined up and fitted, remove original rear fender, drill & tap (2) two 5/16 x 18 holes in rear fender support bracket (see Figure 12). 16. Install Harley Davidson® Part #70909-95 and 47449-97 bracket and receptacle on front and rear bag supports (see Figure 13 & 14). 17. Install Harley Davidson® Part #47449-97 bracket with receptable (see Figure 14). Make sure the bolts come from the inside out. This bracket is adjustable for location.

Incoming search terms:

Harley Davidson Softail Sideshots Exhaust System Installation Manual

0

Filed Under (Harley Davidson) by admin on 20-12-2010

download
STOCK EXHAUST SYSTEM REMOVAL 1. On FLSTN, FLSTF, FLSTH and FLSTC loosen the right hand floor board mounting bolts to gain clearance for exhaust removal and installation. 2. Loosen the heat shield clamps on both front and rear exhaust pipes. 3. Loosen the crossover pipe clamp, located between the front and rear head pipe. (Not necessary on 2000- up models). 4. Remove the two mounting nuts from each head pipe, located at the cylinder head 5. Remove the bolts attaching the mufflers to the frame. 6. Remove the entire exhaust system and set it aside. 7. On pre 2000 models remove the lower mounting bar. 8. FLSTN, FLSTF and FXSTD models have an upper mounting bar that must be removed in addition to the lower bar. On pre 2000 models go to step #9, on 2000-up models go to step #10. 9. Remove the right passenger foot peg bolt. Position the motorcycle on the side stand with a floor jack under the swing arm pivot bolt on the right hand side. Raise the jack just enough to take the weight off the pivot bolt, remove the bolt and stock mounting bar. Reinstall the pivot bolt and torque to 120 -150 ft. lbs. Reinstall the passenger foot peg using the 1/2″ x 3″ Allen bolt and 1-5/8″ length spacer (supplied). 10. Using a #50 Torx driver, remove the three mounting bolts, and set the mounting bar aside. (Two of the bolts are visible, the third is accessed by removing the right hand passenger foot peg.) Replace the foot peg using the 3/8″ x 2 1/2″ Allen bolt and 3/4″ length spacer (supplied). 11. The bolts and spacers used in the above steps may also be used on all Softail models to space the right rear foot peg away from the exhaust. 12. Carefully remove the flanges and circlips from the stock exhaust system using snapring pliers (save for reuse). NOTE: If circlips look bent or twisted replace them with new circlips.

HARLEY DAVIDSON BLADE FRONT WHEEL KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-03-2011

download
INSTALLATION 1. Remove existing front wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to FRONT WHEEL in service manual. For FLSTC and FLSTN Models: Discard moon-style hub cap. or FXSTD: Discard tapered spacer. NOTE Install short valve stem (43157-83A) included in the installation kit. Discard all other valve stems. 2. See Figure 2. Install valve stem assembly (L) on wheel. Refer to TIRES in service manual. Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c) NOTES Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. The side with the machined groove on the hub face is the primary bearing side for all kits except Kits 41681-07 and 40818-08. For Kit 41681-07: Install the wheel so that the hub markings are on the left side and the machined groove is on the right side of the motorcycle. • For 2006 and later FXDWG Models: When correctly installed, the tire will be 0.08-0.2 in (2-5 mm) off of center, compared to the fender. • For 2007 and later FX Softail and 2008 and later FXDWG Models: The left side of the wheel is the primary bearing side. • For 2006 and earlier FX Softail and 2007 and earlier FXDWG Models: The right side of the wheel is the primary bearing side. For Kit 40818-08: • Proper installation of this kit requires the separate purchase of two floating brake discs (44343-01 for 2004 – 2007 models and 44553-06A (stock) or 41500012 (polished) for 2008 and later models) and a tire (43371-07 on 2004-2008 models and 44026-09A on 2009-later models). The left side of the wheel has machined DOT markings to identify it as the primary bearing side. • For 2008 and later Touring: Install bearing shim (43903- 08) under the primary bearing. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in service manual. 4. For FLSTC and FLSTN Models: Install wheel kit and right hand wheel spacer provided in installation kit. Refer to FRONT WHEEL in service manual. For FXSTD Models: Install wheel kit, stock wheel spacer and right side wheel spacer provided in installation kit in place of the tapered spacer discarded in Step 1. Refer to FRONT WHEEL in service manual. For FXSTS Models: Install wheel kit, stock wheel spacers and spacer provided in installation kit between the left side wheel spacer and the left fork. For all other models: Install previously removed wheel spacers. Refer to FRONT WHEEL in service manual. 5. Install front wheel (1), stock axle and stock axle nut. Refer to FRONT WHEEL in service manual. MAINTENANCE AND CLEANING Chrome parts must be maintained regularly to verify that they keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley-Davidson Wheel and Tire Cleaner, applied with Harley Wheel and Spoke Brush. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner. 3. After cleaning and polishing, seal the finish with a good quality sealer, such as Harley Glaze Polish and Sealant