saziki max 100 hatlaiet kaneksan wariegn

You search Auto repair manual PDF saziki max 100 hatlaiet kaneksan wariegn, if there are search results will appear below. If search results do not exist, please search by others keyword.



  saziki max 100 hatlaiet kaneksan wariegn Direct Download speed 5282 Kb/s

  saziki max 100 hatlaiet kaneksan wariegn Full Version speed 6162 Kb/s



Sanyang JET 50/100 and JET Euro 50/100 Specifications And Service Manual

0

Filed Under (Sym) by admin on 24-11-2010

download
Carbon monoxide If you must run your engine, ensure the place is well ventilated. Never run your engine in a closed area. Run your engine in an open area, if you have to run your engine in a closed area, be sure to use an extractor. Caution Exhaust contains toxic gas which may cause one to lose consciousness and even result in death. Gasoline Gasoline is a low ignition point and explosive material. Work in a well-ventilated place, no flame or spark should be allowed in the work place or where gasoline is being stored. Caution Gasoline is highly flammable, and may explode under some conditions, keep it away from children. Used engine oil Caution Prolonged contact with used engine oil (or transmission oil) may cause skin cancer although it might not be verified. We recommend that you wash your hands with soap and water right after contacting. Keep the used oil beyond reach of children. Hot components Caution Components of the engine and exhaust system can become extremely hot after engine running. They remain very hot even after the engine has been stopped for some time. When performing service work on these parts, wear insulated gloves and wait until cooling off. Battery Caution y Battery emits explosive gases; flame is strictly prohibited. Keep the place well ventilated when charging the battery. y Battery contains sulfuric acid (electrolyte) which can cause serious burns so be careful do not be spray on your eyes or skin. If you get battery acid on your skin, flush it off immediately with water. If you get battery acid in your eyes, flush it off immediately with water and then go to hospital to see an ophthalmologist. y If you swallow it by mistake, drink a lot of water or milk, and take some laxative such as castor oil or vegetable oil and then go to see a doctor. y Keep electrolyte beyond reach of children. Brake shoe Do not use an air hose or a dry brush to clean components of the brake system, use a vacuum cleaner or the equivalent to avoid dust flying. Caution Inhaling dust may cause disorders and cancer of the breathing system. Brake fluid Caution Spilling brake fluid on painted, plastic, or rubber parts may cause damage to the parts. Place a clean towel on the above-mentioned parts for protection when servicing the brake system. Keep the brake fluid beyond reach of children

Yamaha V-Star 650 REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 10-01-2012

download
Instruction sheet 54-600 1 Front head pipe 54-600-01F 1 Rear head pipe 54-600-01R 1 Front heat shield 54-600-02F 1 Rear heat shield 54-600-02R 1 Outlaw muffler 50-103-127 1 Muffler bracket 54-600-40 1 Head flange 54-110-41 7 2″ standard hose clamps 70-100-35 2 1 3/4″ HD Hose clamp 70-100-37 2 5/16″-18 carriage bolts 70-100-10 2 5/16″-18 flange nuts 70-100-15 1 8mm x 1.25 x 25mm flange bolt for front head flange 70-100-09 2 8mm x 1.25 x 20mm bolts /muffler bracket 70-100-05 2 10mm x 1.25 x 35mm bolts 70-100-85 2 Spacer .250 x .438 x .875 50-100-74 2 8mm x 1.25 Flange nut 70-100-22
Disassembly 1. Remove both Allen bolts that hold the muffler together (Fig. 1) . Also Loosen clamp from the front muffler to front head pipe (Fig. 2) , and remove allen bolts from rear head pipe and remove in one peace carefully (Fig. 3) . Figure 1 Figure 2 Figure 3 2. Once the two mufflers are removed with the rear head pipe, remove bracket by removing two 8mm bolts as shown and remove bracket. (Fig 4) Figure 4
3. Remove spring from brake light switch to the brake rod located on the right side footrest. (Fig 5) Figure 5 4. Remove two bolts holding the footrest, and brake pedal (Fig. 6) . Carefully rest right side footrest on the floor or you can use a two by four to rest the footrest onto. Figure 6

Incoming search terms:

HERO HONDA CD-100 / SS100 / SLEEK / SPLENDOR / PASSION

0

Filed Under (Honda) by admin on 14-11-2011

download
1500 91255-169-003 30-42-11 FRONT FORK SEAL (S/S) (SLEEK) Improved Quality 200 20 PCS
1500A ————— SET OF 2 PCS FRONT FORK DUST SEAL (S/S) 100 10 PCS 1501 90756-198-000 7-37-7.5 FRONT FORK TRIPLE (COLLER) (CD-100) 200 20 PCS 1502 91202-302-01013.8-24-5 KICK SHAFT 200m20 PCS 1502A 91202-302-010m13.8-24-5+1514 KICK SEAL(SPL.GRADE O.E TYPE) MATERIAL WITH PUCH ROD RUBBER 100 10 PCS 1503 91205-350-000 6-25-6 CLUTCH 200 20 PCS 1504 91202-GK4-722 18.9-30-5 MAGNET
200

Incoming search terms:

Aprilia RS125 Specifications And Repair Manual

0

Filed Under (Aprilia) by admin on 24-11-2010

download
TECHNICAL DATA DIMENSIONS Max. length 1955 mm (76.97 in.) Max. width 720 mm (28.34 ) in. Max. height (at headlight fairing) 1100 mm (43.31 in.) Seat height 805 mm (31.69 in.) Wheelbase 1345 mm (52.95 in.) Minimum ground clearance 163 mm (6.42 in.) Weight in running order (including fluids and fuel) 137 kg (302.03 lb.) ENGINE Type Single-cylinder 2-stroke with reed intake. Separate lubrication with automatic variable mixer ( 1.0 – 3.0 %). Number of cylinders 1 Total displacement 124.82 cu cm (7.62 cu. in.) Bore/stroke 54 mm /54.5 mm (2.12 in. /2.14 in.). Compression ratio 12.5 ± 0.5 : 1 Squish clearance 1.5 mm (0.06 in.) Engine idling speed 1250 ± 100 rpm Engine maximum rpm 11000 ± 100 rpm Ignition CDI ignition system with electronic spark timing Starting Electric starter Clutch Multiplate wet clutch, with control lever on left handlebar Gearbox mechanical, 6-speed, with control pedal on left side of engine Gearbox lubrication Splash lubrication Lubricating system Separate lubrication with automatic variable mixer ( 1.0 – 1.3 %) CAPACITIES Fuel (including reserve) 14 l ± 0.5 l (3.70 USgal ± 0.13 USgal) (3.08 gal ± 0.11 gal) Fuel reserve 3.5 l (0.92 USgal) (0.77 gal) Gearbox fluid 600 cu cm (36.61 cu. in.) Gearbox fluid 600 cu cm (36.61 cu. in.) Coolant 0.8 l (50% water + 50% antifreeze with ethylene glycol) (0.21 USgal) (0.17 gal) Mixer oil (reserve included) 1,7 l (0.45 USgal) (0.37 gal) Mixer oil reserve 0.6 l (0.16 USgal) (0.16 gal) Front fork oil/air 440 ± 2,5 cm³ (26.85 ± 0.15 cuin) Seat 2 Vehicle max. load (rider + passenger + luggage) 180 kg (396.83 lb.) TRANSMISSION SYSTEM GEAR RATIOS Ratio 1st 2nd 3rd 4th 5th 6th Primary 19/63 = 1: 3.316 Final 10/30 = 1: 3.000 14/29 = 1: 2.071 17/27 = 1: 1.588 19/25 = 1: 1.316 21/24 = 1: 1.143 22/23 = 1: 1.045 Final ratio 17/40 = 1: 2.353 Total ratio 1 : 23.406 1 : 16.161 1 : 12.391 1 : 10.266 1 : 8.916 1 : 8.156 FUEL SYSTEM Type Carbureted Model DELL’ORTO PHBH 28 FUEL SYSTEM Fuel Premium-grade unleaded petrol, minimum octane rating 95 (RON) and 85 (MON), as per DIN 51 607

Lilac LS-18 Motorcycle Maintenance Standards

0

Filed Under (Lilac) by admin on 25-11-2010

download
CYLINDER AND CYLINDER HEAD MAINTENANCE ITEM STANDARD REPAIR LIMIT METHOD REMARKS Cylinder Bore 54 -0.01 54.1 Boring After boring honing should be performed Ovality 0.01 0.05 Boring After boring honing should be performed Taper 0.01 0.05 Boring After boring honing should be performed Oversize 0.25 steps 55 max. Do R and L cylinders at same time / 4 steps Valve Seat Width 0.8 – 1.0 1.3 Adjust Use a cutter Angle 45∞ Combustion Chamber Volume 18.2cc -0.5cc Remove carbon if heavy accumulation Compression Ratio 7.8:1 Head Gasket Thickness 1.0 Cylinder Head Nut Torque 3.0 kg/m (22 ft.-lb.) Out standard Adjust 8mm nut Intake and Exhaust Ports Port Wall SurfaceMust be smooth Remove carbon Intake and Exh. Valve GuidesOD 12 +0.09 +0.1 ID 7 +0.01 -0.0 7.06 Exchange Intake Valve Stem Diameter 7 -0.02 -0.03 6.9 Exchange Head Thickness 1 0.7 Exchange Exhaust Valve Stem Diameter 7 -0.02 -0.03 6.9 Exchange Head Thickness 1 0.7 Exchange Intake and Exhaust Valve Seat Face Width Range 0.8~1.0 1.3 Use valve seat cutter Intake Valve Guide Clearance 0.02~0.04 0.08 Replace valve or guide Exhaust Valve Guide Clearance 0.06~0.08 0.12 Replace valve or guide Valve Spring (Large) Installed Load 10.2 kg 8.7 kg Replace Fitted length 31.5 Free Length 36.5 34.7 Replace Tilt 1.5/100 3/100 Replace Valve Spring (Small) Installed Load 5.48 kg 4.65 kg Replace Fitted length 29.5 Page 4 of 10 Free Length 33.5 31.8 Replace Tilt 1.5/100 3/100 Replace Rocker Arm ID 12 +0.00 +0.02112.07 Replace Rocker Shaft OD 12 -0.06 -0.024 11.92 Replace Arm and Shaft Clearance 0.045~0.006 0.10 Replace arm or shaft Tappet Clearance 0.05 Out standard Adjust Measure cold at TDC Rocker Arm Ball Surface 1.8îR -0.006 -0.024 Replace if severe wear Pushrod Bend 0.1 0.5 Straighten Over 100mm (2) CRANKSHAFT, PISTON AND CONROD MAINTENANCE ITEM STANDARD REPAIR LIMIT METHOD REMARKS Piston OD @ Top 53.65 -0.02 Max Diameter 53.95 -0.015 53.85 Replace Ovality 0.1 Piston and Cylinder Clearance 0.04~0.05 0.15 Replace Piston Ring Groove Clearance 0.03~0.07 0.10 Replace Piston Oversize Step 0.25 4 steps Top Ring and 2nd Ring Thickness 2 -0.01 -0.03 1.92 Replace Width 2.5 -0.01 0.55kg Tension 0.85 – 1.15kg 1 Replace End Gap 0.15 – 0.35 Replace Oil Ring Thickness 3.2 -0.01 -0.03 3.12 Replace Width 2.5 -0.1 Tension 1.0~1.3kg 0.65kg Replace End Gap 0.15~0.35 1 Replace Ring Gap Position 120∞ 3 equal spacesOut standard Adjust Avoid Piston Pin Axis Ring Oversizes 0.25 steps 4 steps Piston Pin OD 15 -0.0 +0.006 14.95 Replace Pin Hole in Piston ID 15 +0.012 -0.015.05 Replace Pin and Piston Clearance -0.006 ~ +0.012 0.06 Replace Hand push fit piston at 100∞C Conrod Small End Bush ID 15+0.027+0.016 15.07 Replace bush Conrod and Piston Pin Clearance 0.01~0.027 0.07 Replace Crankpin OD 24.94 +0.0+0.0124.90 Replace Crankpin Roller OD 5 (+0.001+0.003) Refer to conrod ID Replace 3Sizes; 52 per assembly for selective fit 5 (+0.0 -0.002) 5 (-0.003 -0.005) Conrod ID 34.95+0.03+0.02435.02 Axial Play 0.2~0.4 0.5 Adjust Radial Play 0.026~0.036 0.06 Replace

Incoming search terms:

APRILIA QUASAR 50-100-125-180 maintenance Manual

0

Filed Under (Aprilia) by admin on 26-11-2010

download
CHANGING ENGINE OIL CAUTION In case of oil leakage or malfunctions, contact an Aprilia Authorised Dealer . Do not dispose of oil in the environ- ment. Dispose of engine oil – stored in a sealed container – through the nearest waste oil reclamation firm or through the supplier. Carefully read page 34 (MAINTE- NANCE) To change engien oil: ◆ Ride for a few kilometres until engine reaches the operating temperature, then stop the engine. ◆ Position a graduated container (1), under the drain plug (2). ◆ Loosen oil filler plug (4) and drain plug (2). ◆ Let oil flow out of the sump. ◆ Loosen oil filter (3) and carefully clean it. ◆ Refit the filter and tighten fully. ◆ Tighten drain plug (2) and pour recommended oil into filler plug (4), see page 58 (LUBRICANT CHART). ◆ Tighten the filler plug. CAUTION Carefully tighten filler and drain plugs and ensure oil does not leak out. Periodically check for leaks at the casing cover gasket. Do not use the vehicle with insufficient lubrication or with contaminated or unsuitable lubricants, since this would cause early wear of the moving parts and may also cause irreparable failures Fluid reservoir (1) is under rear right wheelhouse. CAUTION Position the vehicle on firm and flat ground. ◆ Make sure that the fluid contained in the reservoir exceeds the ” MIN ” mark stamped on the reservoir. MIN = minimum level. WARNING Do not use the vehicle if the braking system is leaking fluid. CAUTION Do not use the vehicle if the fluid is below the “MIN” mark. 1
27 use and maintenance Quasar 50 – 100 – 125 – 180 CAUTION Brake fluid level decreases as the brake pads wear down. Should the level be too low: ◆ Check the brake discs and pads for wear, see page 27 (CHECKING THE BRAKE PADS FOR WEAR) If the pads and/or the disc do not need re- placing: ◆ Contact an Aprilia Authorised Dealer that will top up the fluid. WARNING Check the brake for proper operation. When the brake lever has exceeding travel or if you notice a loss of braking, contact an Aprilia Authorised Dealer . The braking system may need bleed- ing. CHECKING THE BRAKE PADS FOR WEAR Carefully read page 26 (BRAKE FLUID – recommendations) , page 26 (DISC BRAKES) and page 34 (MAINTE- NANCE). Periodically check brake pad wear. The rate at which brake pads will wear depends on vehicle usage, riding style and road surface condition. Outlined below is a quick brake pad inspection procedure: ◆ Visually check between brake disc and pads, check both pads (1) looking from the bottom at the rear end. ◆ Should friction material (of even one pad only) be worn down to 1.5 mm of thickness, have both pads replaced

Triumph MITY MAX 3 PHASE INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 30-10-2010

download
The output of the Power Control Module is 12 volts for Triumph, BSA and Norton, etc. Polarity is determined by which wire is grounded. (Black for negative ground; red for positive ground) The output of the PCM should be connected to the battery or ignition switch. The PCM case is electrically isolated from the circuitry and does not require grounding. The case must be tightly mounted to some part of the motorcycle that does not vibrate more than the frame and the case must not be allowed to rub or vibrate againt any other component. Tighten the mounting bolts down until there is no free movement. Do not attempt to shock mount the PCM. The guarantee covers defects in workmanship or materials only; defaced or abused PCM’s will not be repaired or replaced without cost. The date stamped on the PCM is the month and year of warranty expiration. (55 would be the end of the 5th month of 2005) Units are warrantied for two years from the date of manufacture

Triumph Mity Max Single Phase PCM INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 30-10-2010

download
The output of the Power Control Module is 12 volts for Triumph, BSA and Norton, etc. Polarity is determined by which wire is grounded. (Black for negative ground; red for positive ground) The output of the PCM should be connected to the battery or ignition switch. The PCM case is electrically isolated from the circuitry and does not require grounding. The case must be tightly mounted to some part of the motorcycle that does not vibrate more than the frame and the case must not be allowed to rub or vibrate againt any other component. Tighten the mounting bolts down until there is no free movement. Do not attempt to shock mount the PCM. The guarantee covers defects in workmanship or materials only; defaced or abused PCM’s will not be repaired or replaced without cost. The date stamped on the PCM is the month and year of warranty expiration. (55 would be the end of the 5th month of 2005) Units are warrantied for two years from the date of manufacture

YAMAHA V-MAX PERIODIC MAINTENANCE AND MINOR REPAIR

0

Filed Under (Yamaha) by admin on 25-11-2010

download
PERIODIC MAINTENANCE AND MINOR REPAIR -. 1. Screw (x 2) EAU03003 Replacing the headlight bulb This motorcycle is equipped with a quartz bulb headlight. If the headlight bulb burns out, replace it as follows. 1. Remove the headlight unit by re- moving the screws. 2. Disconnect the headlight coupler, and then remove the headlight unit and bulb cover. 1. Headlight bulb holder 3. Remove the headlight bulb holder by turning it counterclockwise, and then remove the defective bulb. EWOOOl19 Headlight bulbs get very hot. Therefore, keep flammable products away from a lit headlight bulb, and do not touch the bulb until it has cooled down. 4. Place a new bulb into position, and then secure it with the bulb holder. 1. Do not touch this area. EC000105 Do not touch the glass part of the headlight bulb to keep it free from oil, otherwise the transparency of the glass, the luminosity of the bulb, and the bulb life will be adversely affected. Thoroughly clean off any dirt and fingerprints on the headlight bulb using a cloth moistened with alcohol or thinner. 5. Install the bulb cover, and then connect the coupler. 6. Install the headlight unit by install- ing the screws. 7. Have a Yamaha dealer adjust the headlight beam if necessary. 6-40 PERIODIC MAINTENANCE AND MINOR REPAIR 1. Screw (x 2) 1. Tail/brake light bulb (x 2) EAU00855 Replacing a turn signal light bulb or the tail/brake light bulb 3. Insert a new bulb into the socket, push it in, and then turn it clock- wise until it stops. 1. Remove the lens by removing the screws. 2. Remove the defective bulb by pushing it in and turning it counter- clockwise. 1. Turn signal light bulb 4. Install the lens by installing the screws. EC000108 Do not overtighten the screws, oth- erwise the lens may break

Incoming search terms:

Moto Guzzi Griso V1100 workshop manual

0

Filed Under (Moto Guzzi) by admin on 27-11-2010

download
DIMENSIONS Max. length 2260 mm (88.98 in.) Max. width 880 mm (34.64 in.) Max. height 1070 mm (42.12 in.) (excluding the rear/view mirrors) Seat height 800 mm (31.49 in.) Wheelbase 1554 mm (61.18 in.) Minimum ground clearance 185 mm (7.28 in.) Weight in running order 240 kg (529.1 lb) ENGINE Type twin-cylinder, 90° V transversal, 4-stroke engine Number of cylinders two Cylinder arrangement V, 90° Total displacement 1064 cu cm (65 cu in) Bore/stroke 92 x 80 mm (3.6 x 3.1 in). Compression ratio 9.6 : 1 Starting electric Engine idling speed 1100 ± 100 rpm Clutch dry, twin disc Lubricating system System under pressure, adjustment by valves and vane pump Air filter cartridge, dry Cooling system air cooled TIMING SYSTEM Timing diagram: 2 valves, with rods and rocker arms Values with inspection clearance between rocker arms and valve intake 0.10 mm (0.0039 in.) exhaust 0.15 mm (0.0059 in.) CAPACITIES Fuel (reserve included) 17.2 litres Fuel reserve 3.3 litres Engine oil Engine oil and oil filter change 3600 cu. cm (219 cu in) Gearbox fluid 500 cu cm (30.5 cu in) Transmission fluid 380 cu cm (23.2 cu in) Fork oil 520±2.5 cu cm (31.7 ± 1.5 cu in) (per leg) Seats 2 Max. vehicle load 210 kg (462.97 lb) (rider + passenger + luggage) TRANSMISSION SYSTEM primary drive gear, ratio: 24/35 = 1:1.4583 gearbox Mechanic, with 6 speeds, controlled by a pedal on engine left side overall gear ratios: 1st gear 17/38 = 1:2.2353 2nd gear 20/34 = 1:1.7 3rd gear 23/31 = 1:1.3478 4th gear 26/29 = 1:1.1154 5th gear 31/30 = 1:0.9677 6th gear 29/25 = 1:0.8621 final drive with cardan joint ratio 12/44 = 1:3.6667 FUEL SYSTEM Type Electronic injection (Weber – Marelli) with stepper motor Choke Ø 36 mm (1.417 in.) Fuel Premium grade unleaded petrol, minimum octane rating 95 (RON) and 85 (MON). FRAME Type Tube, with double cradle in high-strength steel Steering head angle 26°30′ Trail 108 mm (4.25 in.)