roadmax transmission parts

You search Auto repair manual PDF roadmax transmission parts, if there are search results will appear below. If search results do not exist, please search by others keyword.



  roadmax transmission parts Direct Download speed 5282 Kb/s

  roadmax transmission parts Full Version speed 6162 Kb/s



HARLEY DAVIDSON ENGINE/ TRANSMISSION INTERFACE AND TOP COVER INSTALLATION

0

Filed Under (Harley Davidson) by admin on 25-12-2010

download
1. Refer to the Owner’s Manual and follow the instructions given to remove the maxi-fuse. 3 1 2 is02998 1. Transmission top cover screw (4) 2. Oil spout assembly screw 3. Upper bearing housing screw (2) Figure 1. Interface Cover Installation 2. See Figure 1. Remove and retain the four socket head cap screws (1) that fasten the front and right side of the transmission cover. See Figure 3. Obtain the chrome top interface cover (3) from the kit. NOTE The top interface cover can be carefully brought into position on top of the transmission housing from either the right or left side without removing or loosening any vehicle components. 3. Position the top interface cover over the transmission top cover. Loosely fasten the chrome cover to the top of the transmission housing with the screws removed in Step 2. 4. Obtain the chrome filler neck cover (4), 1/4-20 socket head screw (5), flat washer (6) and spacer (7) from the kit. Remove the oil level dipstick from the oil spout on the side of the transmission housing, wipe off and set it aside for later installation. NOTE Insert a clean shop rag into the oil spout opening while the dipstick is not installed. With the dipstick removed, small parts or other foreign material could fall into the transmission, leading to equipment damage or malfunction. 5. See Figure 1. Remove and discard the socket head cap screw (2) that fastens the oil spout assembly to the transmission housing. DO NOT remove the oil spout from the vehicle. 6. Place the flat washer over the threads of the new screw, and insert the screw into the unthreaded hole in the chrome filler neck cover. Place the spacer onto the screw threads. Apply a few drops of Loctite® 243 (Blue) to the screw threads, and position the chrome cover onto the oil spout on the transmission housing. Lubricate the filler neck gasket with soapy water to aid in installation. Tighten the screw to 84-132 in-lbs (9.5-15 Nm) . 7. See Figure 3. Obtain the chrome lower side interface cover (1), one #10-24 socket head screw (8) and one chrome flat washer (9) from the kit. NOTE For models with mid controls, the right-side rider footrest (foot peg) support bracket must be loosened to allow installation of the lower side interface cover. After the cover has been installed, tighten the footrest bracket attaching screws to 25- 35 ft-lbs (34-47 Nm) . 8. Position the cover around the chrome filler neck cover installed in Step 6. Loosely fasten the cover to the threaded hole in the filler neck cover with the screw and washer. 9. Obtain the chrome upper side interface cover (2), three #10-24 socket head screws (8) and three chrome flat washers (9) from the kit

HARLEY DAVIDSON ENGINE/ TRANSMISSION INTERFACE AND TOP COVER INSTALLATION INSRUCTIONS

0

Filed Under (Harley Davidson) by admin on 31-01-2011

download
INSTALLATION Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) 1. Refer to the Owner’s Manual and follow the instructions given to remove the maxi-fuse. 3 1 2 is02998 1. Transmission top cover screw (4) 2. Oil spout assembly screw 3. Upper bearing housing screw (2) Figure 1. Interface Cover Installation 2. See Figure 1. Remove and retain the four socket head cap screws (1) that fasten the front and right side of the transmission cover. See Figure 3. Obtain the chrome top interface cover (3) from the kit. NOTE The top interface cover can be carefully brought into position on top of the transmission housing from either the right or left side without removing or loosening any vehicle components. 3. Position the top interface cover over the transmission top cover. Loosely fasten the chrome cover to the top of the transmission housing with the screws removed in Step 2. 4. Obtain the chrome filler neck cover (4), 1/4-20 socket head screw (5), flat washer (6) and spacer (7) from the kit. Remove the oil level dipstick from the oil spout on the side of the transmission housing, wipe off and set it aside for later installation. NOTE Insert a clean shop rag into the oil spout opening while the dipstick is not installed. With the dipstick removed, small parts or other foreign material could fall into the transmission, leading to equipment damage or malfunction. 5. See Figure 1. Remove and discard the socket head cap screw (2) that fastens the oil spout assembly to the transmission housing. DO NOT remove the oil spout from the vehicle. 6. Place the flat washer over the threads of the new screw, and insert the screw into the unthreaded hole in the chrome filler neck cover. Place the spacer onto the screw threads. Apply a few drops of Loctite® 243 (Blue) to the screw threads, and position the chrome cover onto the oil spout on the transmission housing. Lubricate the filler neck gasket with soapy water to aid in installation. Tighten the screw to 84-132 in-lbs (9.5-15 Nm) . 7. See Figure 3. Obtain the chrome lower side interface cover (1), one #10-24 socket head screw (8) and one chrome flat washer (9) from the kit

HARLEY DAVIDSON ENGINE/TRANSMISSION INTERFACE AND TOP COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-04-2011

download
INSTALLATION Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) 1. Refer to the Owner’s Manual and follow the instructions given to remove the maxi-fuse. 1 4 3 2 is03621 1. Transmission top cover screw (3) 2. Upper and lower rear bearing housing screw (2) 3. Upper front bearing housing screw 4. Lower front bearing housing screw Figure 1. Interface Cover Installation 2. See Figure 1. Remove the two rear bearing housing screws (2) from the side of the transmission case. 3. Remove the oil level dipstick from the oil spout on the side of the transmission housing, wipe off and set it aside for later installation. NOTE Insert a clean shop rag into the oil spout opening while the dipstick is not installed. With the dipstick removed, small parts or other foreign material could fall into the transmission, leading to equipment damage or malfunction. 4. See Figure 2. Obtain the rear interface mounting bracket (1) from the kit. 5. Apply a few drops of Loctite 243 (Blue) to the threads of the two bearing housing screws removed in Step 2. Install the rear interface mounting bracket to the bearing housing with the screws, and tighten to 13-18 ft-lbs (17.6-24.4 Nm) . 6. See Figure 1. Remove the upper front bearing housing screw (3) from the side of the transmission case. Loosen the lower front bearing housing screw (4). 7. See Figure 2. Obtain the front interface mounting bracket (2) from the kit. 8. Apply a few drops of Loctite 243 (Blue) to the threads of the upper front bearing housing screw removed in Step 6. Hook the slot in the front interface mounting bracket under the loosened lower screw head. Install the bracket to the bearing housing with the upper screw, and tighten both screws to 13-18 ft-lbs (17.6-24.4 Nm) . 9. See Figure 1. Remove and retain the three socket head cap screws (1) that fasten the right side and left front corner of the transmission cover. 10. Remove and retain the screw fastening the rear brake line P-clamp to the rear fork bracket. 11. See Figure 2. Obtain the right rear interface cover (3), two chrome 1/4-20 screws (6) and two flat washers (7) from the kit. 12. From the rear of the motorcycle, bring the right rear interface cover into position behind the rear exhaust pipe, over the bearing housing. The hole in the top surface of the cover should be positioned over the right rear transmission top cover hole. 13. Loosely fasten the interface cover to the rear interface mounting bracket with the two chrome screws and flat washers. 14. Obtain the chrome top interface cover (4) from the kit. 15. Position the top interface cover over the transmission top cover, overlapping the tab at the top front of the chrome right rear interface cover

A750 Transmission Solenoid Identification Automatic Transmission/ Transaxle

0

Filed Under (Toyota Manuals) by admin on 19-09-2011

Download
Provided below isachartlisting the Repair Manual name of each solenoid used in the A750 transmission, as well as the part name description provided in the electronic parts catalog. REPAIR MANUAL SOLENOID NAME PARTS CATALOGP ART DESCRIPTION S1 3WayTransmission Solenoid S2 Transmission Solenoid#3 SL1 Clutch Control Solenoid#1 SL2 Clutch Control Solenoid#2 SLT Line Pressure Control Solenoid SLU Lock UpControl Solenoid SR

HARLEY DAVIDSON CHROME TRANSMISSION HARDWARE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 17-03-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect battery cable, negative (-) cable only. NOTE The starter does not need to be removed to install this kit. 2. Remove exhaust system only if needed to access transmission top cover hardware. Refer to Service Manual for instructions. NOTES Replace existing zinc hardware with chrome-plated hardware one at a time so the transmission top and side covers do not need to be replaced. 3. Remove and discard existing six 1/4-20 x 1 in. hex socket- head screws and washers from top transmission cover. Install six chrome hex socket head screws (1) and washers (2) on top transmission cover (3). Tighten to 84-108 in-lbs (9.5-12.2 Nm). 4. Remove and discard existing two 1/4-20 x 1 in. hex socket head screws and washers from side transmission cover. Install two chrome hex socket head screws (1) and washers (2) on side transmission cover (5). Tighten to 84- 108 in-lbs (9.5-12.2 Nm). 5. Remove and discard existing four 1/4-20 x 1-1/2 in. hex socket head screws and washers from side transmission cover. Install four chrome hex socket head screws (4) and washers (2) on transmission side cover (5). Tighten to 84- 108 in-lbs (9.5-12.2 Nm). 6. Install exhaust system if previously removed. Refer to Service Manual for instructions. 7. Connect negative (-) battery cable

Harley-Davidson Motorcycle Reverse Gear Installation Instructions

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
2.1 Obtain a small tube of Loctite® #262 (red) for use later. 2.2 Drain the transmission oil. 2.3 Remove the clutch adjustment cover (left side). 2.4 Remove rear exhaust header pipe (cross over exhaust pipe). 2.5 Remove the muffler support bracket. 2.6 Remove the clutch release cover (right side). 2.7 Remove clutch push rod and oil slinger. To be disassembled and modified later. 2.8 Remove the two nuts from the main (rear) and counter (front) transmission shafts. 2.9 Remove the transmission bearing housing (puller available from Champion Sidecars). To be replaced with new reverse gear transmission bearing housing (Trap Door). 2.10 Cover the exposed gears in the transmission with a cloth in preparation to cut the shifter fork shaft. 3 Install New Main and Countershaft Gears NOTE: Gears and Tapered Split Rings are factory matched sets. Do not mix!. 3.1 Locate the shifter fork rod, mark fork rod flush at transmission case and pull out 1/4″. Figure 1 Figure 2. Exposed Shoulders Mark shifter fork rod flush with case Remove Spacers Vehicle Transmission Counter Shaft Main Shaft Front of Motorcycle Figure 1
Reverse Gear Installation Instructions For EVO / 5 Speed and Twin Cam Harley-Davidson® Motorcycle Page 3 of 6 Revision 7 © 2007 Champion Motorcycle Accessories International, Inc. dba Champion Sidecars 11841 Monarch Street Garden Grove, CA 92841 (800) 875-0949 (714) 847-0949 www.championsidecars.com www.championtrikes.com Figure 6 CAUTION: Do not pull the shifter fork rod out of the transmission more than 1/4″. If you pull the shifter fork rod out too far, it will be difficult to realign it with the internal shifter fork. 3.2 Cut the shaft at the mark and push it back in. The shaft end MUST NOT stick out of the transmission case. If the shaft is in deeper, fill the hole with silicone to prevent the shaft from moving in and out. NOTE: Shifter fork is made of non-tempered metal and may be cut with a hacksaw or Dremel® cutting tool. 3.3 Important: Remove stock spacers from main and counter shafts. Spray with silicon remover (Brake-Clean) then, using supplied cleaning pad, clean shafts, new counter and main shaft gears and tapered lock rings (inside and outside) Figure 1 3.4 With motorcycle in neutral, pull both the shafts out and simultaneously push the OEM outermost gears in until seated completely to expose the shoulders of both shafts. The countershaft shoulder should be flush with the gear face. For the main shaft the gear would “hang over” the shoulder a small bit. Figure 2 3.5 Apply supplied Champion Super-Lock retaining compound to the inside and outside surfaces of the large gear tapered split ring, to the inside of the new countershaft gear (large gear) and to the transmission countershaft (the forward most shaft). 3.6 Install new countershaft gear to the transmission countershaft. Insert tapered split ring (tapered end first) into the countershaft gear. Install ring seat tool and spring to counter shaft and new countershaft gear. Torque ring seat tool to 40 ft-lb’s. Figures 3 and 4

Incoming search terms:

Automatic Transmission/ Transaxle Fluid Level Inspection Temperature Rang es

0

Filed Under (Toyota Manuals) by admin on 12-10-2011

download
For vehicles equipped witha transmission requiring the use of the overflow type automatic transmission fluid (ATF) inspection process, the A TF must be withinaspecific temperature range for accurate fluid level inspection. Inspecting the A TF outside of the specified temperature range may result in incorrectA TF fluid levels and could lead to shift quality, M.I.L. “ON”, and/or transmission damage issues. Please seethe information in this bulletin for updated A TF level inspection temperature ranges. HINT For additional information including animations and video illustrations, please seethe Technical Training course E076: “Toyota ATF Level Inspection”. NOTE Please see TSB No. TC 010-07, “World Standard Automatic Transmission Fluid”, for important tips when working with A TFWS. ©2008 ToyotaMotor Sales, USA Page 1of3
T-SB-0129-08 July9,2008 Page 2of3 Automatic Transmission/Transaxle Fluid Level Inspection Temperature Ranges Warranty Information OP CODE DESCRIPTION TIME OFP T1 T2 N/A Not Applicable to Warranty – - — Parts Information PREVIOUS PART NUMBER CURRENT PART NUMBER PART NAME QTY 00289-ATFWS Same ATFWS As needed Required Tools&Equipment

Rokon Illustrated Repair Procedures and Parts Manual

0

Filed Under (Rokon) by admin on 20-11-2010

download
Front and Rear Brake. Check brake action. Check pucks to see that they are not over worn. There should be visible brake material on both sides of the brake disc. See Section 6. Fuel Tank. Check fuel level. Fill as necessary. Use super unleaded for altitudes above 10,000 ft. Engine Oil. The engine holds .6 qt. of SAE10W30/40 motor oil. Fill to the dipstick “full” line. Miter Box and Transmission. They are filled at the factory and need not be checked at the start. The miter box should have 2.5 oz. of EP 80W90 gear lube oil. The transmission takes 6 oz. of EP 80W90 gear lube oil. The transmission has a fill to plug near the bottom of the transmission( shown on page 46). There is no fill level for the miter box. Over filling of either the miter box or transmission will result in leakage. Throttle. Check for proper throttle cable operation. Look for smooth response to twist action. Wheels and Tires. Check Tire pressure, wear and damage. Fittings and Fasteners. Check all fittings and fasteners. Drive Chains. Check chains for tension and lubrication. Adjust tension for 1/2″ – 3/4″ deflection at mid point. Engine Manual. Read your engine manual completely and follow all instructions Periodic Maintenance and Adjustment 1. Inspect all fasteners for tightness. 2. The drive chains require adjustment at intervals, depending on the mileage and the care which the operator has given the chains. Initial wear must be taken up by adjustment after the first few hours of use. Total deflection should be 1/2″ to 3/4″ when measured midway between the two sprockets of the most loose position. To adjust the chains, loosen the axle bolts and the adjusting bolt lock nuts, and turn the adjusting bolts equally in or out as required to give the chain the proper setting. After adjusting the chain, rotate the wheel and check to make sure the chain is aligned properly. Periodically, the chains should be removed from the machine and cleaned in solvent and re-lubricated. They should be lubricated with one of the chain lubricants on the market which can be applied to the chain in a liquid form and will penetrate to the inner parts of the rollers. 3. Clean the air filter based on use. See Engine Manual. 4. Use normal repair procedures for tires and tubes. Re-seat the tire beads with 40 PSI , then deflate to the 3 -5 PSI operating pressure.

Honda CBR 400RR Service and Repair Manual

0

Filed Under (Honda) by admin on 16-12-2011

download
Once you have found al1 the identification nurnbers, record thern for reference when nbuying parts. Since the rnanufacturers change specifications, parts and vendors (cornpanies that rnanufacture various cornponents on the
rnachine), providing the ID nurnbers is the only av to be reasonablv sure that vou are buvina Model, c ~ d e and
production year CBR400RR-J (1988) CBR400RR-K (1 989) CBR400RR-L (t990 and 91) CBR400RR-N (1992 and 93) CBR400RR-R (1 994-on) , the correct parts. Whenever possible, take the worn pari to the dealer so direct cornparison with the new cornponent can be rnade. Along the trail frorn the rnanufacturer to the parts shelf, there are nurnerous places that the part can end up with the wrong nurnber or be listed incorrectly. The two places to purchase new parts for
your rnotorcycle – the accessory shop and the rnotorcycle dealer – differ in the type of parts they carry. While dealers can obtain virtually every part for your rnotorcycle, the accessory shop is usually lirnited to norrnal high wear iterns such as shock absorbers, tune-up parts, various engine gaskets, cables, chains, brake parts, etc. Rarely will an accessory outlet have rnajor suspension cornponents, cylinders, transrnission gears, or cases. Used parts can be obtained for roughly half the price of new ones, but you can’t always be sure of what you’re getting. Once again, take your worn part to the breaker for direct cornparison. Whetherhu~ng new, used or rebuilt parts, the best course is to dea1 directly with sorneone who specialises in parts for your particular rnake. Frame nwnber NC23-1020001 t0 1036454 NC23 t090001 t0 10981 16 NC29-1000001 to 101 0598 NC29-1050001 on NC29-l t00001 on Unofficial (grey) imports
All CBR400RR rnodels in the LIK are unofficial (grey) irnports frorn Japan. The rnajority are second-hand rnachines and are allocated age-related licence plates for UK use (the licence plate letter reflects the production year in Japan), although new CBRs are allocated current year UK registration letter plates. Cornrnon changes rnade prior to sale in the UK are the disabling of the rev-lirniter device (or more correctly ‘speed-lirniter’ device), which is fitted to cornply with Japanese rnarket regulations. The device is located inthe speedorneter head and is linked to th

Incoming search terms:

New Automatic Transmission for Motorcycles Human-Friendly Transmission

0

Filed Under (Honda) by admin on 18-12-2011

download
High-pressure fluid flow The engine rotates the pump swash plate, which has a gear mechanism. The rotating swash plate pushes the pump pistons to increase the pressure on the hydraulic fluid and feed it to the high-pressure annular chamber. The high- pressure fluid is then fed to the oil motor piston chamber where it pushes the pistons forward, which then push the motor swash plate. Power Fluid flow from pump to motor Fluid flow from motor to pump Low-pressure fluid flow The lower-pressure hydraulic fluid returns to the pump through the low-pressure annular chamber. In this way, the fluid circulates between the pump and the motor. Movement of distributor valves and pistons The distributor valves play an important role in fluid circulation. The valves are placed both in the oil pump and motor. When the pump pistons move to the compression side, the valves connect the piston chamber and the high- pressure chamber. When the pump pistons move to the expansion side, the valves allow a connection between the piston chamber and the low-pressure chamber. The valve in the oil motor moves opposite to its counterpart in the pump, ensuring the circulation of fluid within the system