r15 odaneter details

You search Auto repair manual PDF r15 odaneter details, if there are search results will appear below. If search results do not exist, please search by others keyword.



  r15 odaneter details Direct Download speed 5282 Kb/s

  r15 odaneter details Full Version speed 6162 Kb/s



Honda CBR-929RR/ 954RR – Installation Instructions (slip on system)

0

Filed Under (Honda) by admin on 03-11-2011

download
Remove the lower fairing. Remove the rear turn signals. Remove the existing exhaust system from the HTEV valve rearward, save the mounting bolts for reuse. Save the stock exhaust can mounting bolt and nut for the end can to the passenger footpeg for reuse as well. Install the supplied HTEV joint plate to the rear of HTEV valve (see photo 1) using the stock mounting bolts. Tighten per factory specifications. Install the 2 Y-pipes to the joint plate, but do not install the supplied springs at this time. Install the S-Bend to the two Y-pipes, but do not install the supplied springs at this time. If you plan to keep the passenger footpegs, follow this step, otherwise, skip to step 8. Reassemble the right
passenger footpeg assembly in this order (from the subframe outwards): Spacer A, Stay Arm F, Spacer B, passenger footpeg assembly (from step 7 above). Use the supplied 8x110mm bolts D (2x) to fasten to the subframe (reuse nuts). See figure 3 for details. Proceed to step 8. If you plan to remove the passenger footpeg assemblies, follow this step and ignore step 6 above. Use: Spacer A and place the Stay Arm F against it. Use the supplied 8x50mm bolts E (2x) to fasten to the subframe (reuse nuts). See figure 3 for details, but use only the hardware specified in this step.
Slide the TiForce end can into place. Loosely attach the two rubber bands, stainless steel bands K, and stay / hanger G to the end can using the supplied 6mm hardware H. See figure 1 for details. Place the bands approximately 120mm from the edge of the end can. See figure 2 for details.

Ducati 748 biposto specification

0

Filed Under (Ducati) by admin on 11-11-2010

download
part Number: G790-100-12A Description: Gasket Exhaust 4 Valve Belt product Details: Vee Two Gasket Sets are die cut from high quality gasket material and are supplied with ‘O’ Rings and Oil Seals. uoM: each Year from : all Year to : all part Number: V2-02-7307 Description: Main Bearing – Fits all 2 V + 4 V Belt to 2006 product Details: These bearings are carefully sourced from high end manufacturers and are supplied ro match the specific Bearing Clearances and fitting tolerances required for their particular requirements. uoM: each Year from : all Year to : all part Number: V2-03-604A Description: Camshaft – Road Drop In – Kit of 2 cams inlet only product Details: Drop in Street / Track camshaft, suited to predominately bigger bore 4 valve motors. Gives great bottom end feel due to increased torque. uoM: kit Year from : all Year to : all part Number: V2-03-606 Description: Camshaft – Track – Kit of 4 cams product Details: A predominately race bred camshaft made to produce horsepower at high revs. Very strong above 8500rpm. Must have a very high compression ratio motor, 13.5-1 minimum. uoM: kit Year from : all Year to : all

EDELBROCK NITROUS SYSTEM UNIVERSAL MOTORCYCLE NITROUS SYSTEM

0

Filed Under (Suzuki) by admin on 26-11-2010

download
Wiring Diagram #1 Wiring Diagram #2 Red Red Red Red Black Black Black Black Black Black Factory Harness to Horn Factory Harness to Horn Horn Horn Nitrous Solenoid Nitrous Solenoid Switch Switch Bottom View Bottom View +12V with Key On From Horn Button (Ground when button is pressed) From Horn Button (Ground when button is pressed) To Nitrous Bottle To Nitrous Bottle To Nitrous Nozzle To Nitrous Nozzle Install Relay for OPTIONAL RPM Activated Switch Here. See Section 7.0 for More Details. Install Relay for OPTIONAL RPM Activated Switch Here. See Section 7.0 for More Details ©2007 Edelbrock Corporation Brochure #63-71940 Catalog #71940 Rev. 2/07 – DC/mc Page 4of 4 To Nitrous Bottle To Nitrous Nozzle Nitrous Solenoid To Starter Solenoid Switch Bottom View Ground Starter Button +12V when Pushed Install Relay for OPTIONAL RPM Activated Switch Here. See Section 7.0 for More Details. Wiring Diagram #3 Starter Button Activation for Suzuki Hayabusa 7.0 – WIRING MSD 8950 RPM SWITCH NOTE – This is a suggested wiring application. There are many ways that the RPMswitch may be installed. The installer needs to set RPMswitch to proper RPM and test operation. Use diagrams on page 3 for relay terminal #30 connection. Nitrous Solenoid To Nitrous Bottle To Nitrous Nozzle RPM ACTIVATED SWITCH 10,000 Desired RPM Chip Here Connect as Outlined in Wiring Diagrams White to 4-Coil Tach Adapter #T-101-MSD Black Battery Ground Yellow – N/C Gray – OFF When Set RPMis Exceeded Connect as Outlined in Wiring Diagrams NOTE – RPM Chips are Ordered Separately Red to Switched +12 Volt Tailight Power or any Other +12 Volt Source with the Key On Note – This Method Will Turn the Nitrous Off When Set RPM has Been Exceeded. 85 87A 30 86 87 A Test Light Can Be Used Here to Check Operation 8.0 – OPTIONAL PRODUCTS FOR EFI MOTORCYCLES A Progressive Timing Retard Controller is available from Schnitz Racing for fuel injected motorcycles. The EFIR Series Timing Retard Controllers can be used with or without a Power Commander installed.

2007 Harley-Davidson CVO Family: Specifications

0

Filed Under (Harley Davidson) by admin on 02-11-2010

download
1. Harley-Davidson reserves the right to discontinue models or change specifications at any time without incurring any obligations. Vehicle specifications may vary by country and region depending on local laws. Some models are not available i certain countries. 1. Harley-Davidson reserves the right to discontinue models or change specifications at any time without incurring any obligations. Vehicle specifications may vary by country and region depending on local laws. Some models are not available in certain countries. 1. Harley-Davidson reserves the right to discontinue models or change specifications at any time without incurring any obligations. Vehicle specifications may vary by country and region depending on local laws. Some models are not available in certain countries. 2. Measurement reflects 81.7 kg operator weight. 2. Measurement reflects 81.7 kg operator weight. 2. Measurement reflects 81.7 kg operator weight. 3. Recommended 91 octane or higher fuel (R+M)/2 (87 octane or higher for XL 883 models). Standard and optional fuel systems may vary by country and region. 3. Recommended 91 octane or higher fuel (R+M)/2 (87 octane or higher for XL 883 models). Standard and optional fuel systems may vary by country and region. 3. Recommended 91 octane or higher fuel (R+M)/2 (87 octane or higher for XL 883 models). Standard and optional fuel systems may vary by country and region. 4. Standard and optional wheels may vary by country and region. 4. Standard and optional wheels may vary by country and region. 4. Standard and optional wheels may vary by country and region. 5. Values shown are nominal. Performance may vary by country and region. 5. Values shown are nominal. Performance may vary by country and region. 5. Values shown are nominal. Performance may vary by country and region. 6. Security systems include the immobiliser and siren. 6. Security systems include the immobiliser and siren. 6. Security systems include the immobiliser and siren. 7. Availability of colours may vary from dealer to dealer and is subject to change without notice. 7. Availability of colours may vary from dealer to dealer and is subject to change without notice. 7. Availability of colours may vary from dealer to dealer and is subject to change without notice. 8. Model not available in all markets. 8. Model not available in all markets. 8. Model not available in all markets. 9. See motorcycle owner’s manual for complete details. 9. See motorcycle owner’s manual for complete details. 9. See motorcycle owner’s manual for complete details. 10. Inspections of certain systems and components are required at 4,000 km intervals. 10. Inspections of certain systems and components are required at 4,000 km intervals. 10. Inspections of certain systems and components are required at 4,000 km intervals.

Incoming search terms:

Honda CBR-600 F4 / F4i – Installation Instructions (slip-on)

0

Filed Under (Honda) by admin on 11-11-2011

download
Remove the lower fairing. Remove the existing exhaust system from the middle of the stock pipe. Save the stock exhaust can mounting bolt and nut for the end can to the passenger footpeg for reuse as well. Remove the clamp from the stock exhaust system and save for reuse. Install the S-Bend to the rear of the stock head pipe. Reuse the stock clamp, but do not tighten at this time. Slide the TiForce end can into place. Loosely attach the two rubber bands, stainless steel bands K, and stay / hanger G to the end can using the supplied 6mm hardware H. See figure 1 for details. Place the bands approximately 190-200mm from the edge of the end can. See figure 2 for details.
Using the stock provided mounting point on the passenger footpeg, and using the stock mounting bolt, mount
the end can loosely, allowing for some adjustment. Insert the stock mounting bolt through the stay / hanger G.
Attach the supplied springs to fasten the end can to the S-bend pipe. Make sure the exhaust system is free and clear, if necessary jiggle the system to adjust for proper clearance. Carefully align the two stainless bands K so that they are parallel to each other, and spaced prope rly on the can (refer to step 7 / figure 2), then tighten the 6mm hardware H and the stock mounting bolt hardware. Make sure that the rubber pads fully cover the band(s). USE CAUTION WHEN TIGHTENING THE 6MM HARDWARE AND THE TWO BANDS SO AS NOT TO CRUSH OR DISTORT THE SLEEVE OF THE CAN. Using some brake and contact cleaner on a clean rag, carefully wipe down the entire exhaust system

Twin Tec Installation Instructions for TC88A-IH Ignition

0

Filed Under (Tips and Review) by admin on 29-11-2010

download
INSTALLATION ON 2004 MODELS 1. Turn off the ignition switch and disconnect the battery ground cable before proceeding. 2. Refer to Figures 2 and 3 for wiring details. 3. Remove the Gill Module. 4. Cut off the OE 18 terminal AMP connector used with the Gill module. Refer to the terminal list. Crimp new Deutsch terminals on the wires, and install into the 12 terminal Deutsch connector required by the TC88A-IH module. 5. Install the new TC88A-IH module. 6. Reconnect the battery ground cable. INSTALLATION ON 2005 AND LATER MODELS 1. Turn off the ignition switch and disconnect the battery ground cable before proceeding. 2. Refer to Figures 4 and 5 for wiring details. 3. Remove the Gill Module. 4. Cut off the OE 18 terminal AMP connector used with the Gill module. 5. The crankshaft position (CKP), MAP, and engine temperature (ET) sensor share a common ground Daytona Twin Tec LLC, 933 Beville Road, Suite 101-H, S. Daytona, FL 32119 TC88A-IH (386) 304-0700 www.daytona-twintec.com 10/2009 Page 2 return. This is not compatible with the TC88A-IH and some rewiring will be required. The temperature sensor is not used, but does not require removal. 6. Trace the BK/GN ground return wires from terminal B of the ET sensor and terminal A of the MAP sensor to where they join the BK/GY ground return wire from the CKP sensor. Cut the ET and MAP sensor ground return wires off at this point. You can tape up the ground return wire from the ET sensor – this wire will not be used. 7. Extend the ground return wire from terminal A of the MAP sensor up to the ignition module, crimp on a Deutsch terminal and install in position 4 on the Deutsch connector. 8. Refer to the terminal list. Crimp new Deutsch terminals on the remaining wires, and install into the 12 terminal Deutsch connector required by the TC88A-IH module. 9. Use a DVM to verify isolation (no continuity) between terminals 4 and 9 on the Deutsch connector. 10. Verify continuity between terminal A at the MAP sensor and terminal 4 on the Deutsch connector. 11. Verify continuity between terminal 2 at the CKP sensor and terminal 9 on the on the Deutsch connector. 12. Install the new TC88A-IH module. 13. Reconnect the battery ground cable. Terminal List for American IronHorse Ignition Conversion TC88A Deutsch Connector OE AMP Connector Signal Wire Color Code 1 2 +12V Power W/R

Incoming search terms:

HARLEY DAVIDSON FORK MOUNTING KIT INSTALLATION INSTRUCTION

0

Filed Under (Harley Davidson) by admin on 10-04-2012

download
1. Insert two additional screws into the rear of the extrusion of the light head. See instruction sheet packaged with light head for details. 2. See figure 1. Secure the mounting brackets to the directional Cuda TriOptic light head using the #8-32 KEPS nuts and screws supplied with this kit and light heads. Ensure that drain holes in the light head will be pointing down when installed on the motorcycle. Refer to instructions packaged with light head for details. 3. See figure 2. Remove and retain the top screw from the fork as shown. Attach the assembled bracket to the fork using the previously removed screw and hand tighten the screw. 4. See figure 3. Remove and retain the bottom screw. Rotate the bracket assembly to align with the bottom hole. Replace the previously removed screw. Tighten all hard he Model 350213-03 is a kit for mounting Cuda TriOptic light heads 351012 & 351023 devices to the side of the forks on a Harley Davidson motorcycle. This kit uses hardware supplied with Cuda TriOptic light heads. B. UNPACKING. After unpacking the kit, inspect it for damage that may have occurred in transit. If the unit has been damaged, do not attempt to install or operate it. File a claim with the carrier, stating the extent of damage. Carefully check all envelopes, shipping labels, and tags before removing or destroying them. Ensure that the parts listed in the KIT CONTENTS LIST are included in the package.

Harley Davidson Softail 1987 to Current Trike Conversion Installation Manual

0

Filed Under (Harley Davidson) by admin on 05-03-2012

download
Protect yourself and others when you have a vehicle up in the air. Anytime you lift a vehicle, either by hoist or a jack, make sure that it is securely supported. b. c. d. e. f. Make sure the engine is turned off before you begin work. • Carbon Monoxide poisoning from exhaust gases: Be sure there is adequate ventilation whenever you run the engine. • Burns from hot parts: Let the engine and exhaust system cool before working on those areas. • Injury from moving parts: If running the engine, keep hands, fingers and clothing away from moving/rotating parts. Gasoline vapor and hydrogen gases from batteries are explosive. To reduce the possibility of fire or explosion, be careful when working near gasoline and batteries. Use only nonflammable solvent, not gasoline, to clean parts Never drain or store gasoline in an open container. Keep all cigarettes, sparks or flame away from the battery and all fuel related parts. 1.4 Specifications Overall Length: 66″ Body Length: 92″ Wheel Base: 53″ Load Capacity: 620 Lb Tire Size (15″): 205 / 70 / R15 Wheel Size (15″) (4 lug) Offset +35 mm 15x7JJ 4×4.5 – (Current Installations – Alum Rear End) Wheel Size (15″) (5 lug) Offset +35 mm 15x7JJ 5×4.5 – (Later Installations – Black Rear End) Tire Size (16″) 215 / 60 / R16 Wheel Size (16″) (5 lug) Offset +40 mm 16x7JJ 5×4.5 – (First Installations – Black Rear End) Tire Pressure: 20 PSI Suspension: Internal Swing Arm utilizing OEM shocks Rear Differential: Custom-built rear differential utilizing OEM drive belt. Brakes: Original front plus 2 high performance disc brakes at rear. Storage Capacity: 3.75 cubic feet. 2 full-face helmets and additional storage

Honda Goldwing GL1800 Solid Rear Axle Trike Conversion Installation Manual

0

Filed Under (Honda) by admin on 16-02-2011

download
Specifications Overall Width: 57.75″ Overall Length: 108″ Overall Length w/EZ-Steer 109.5 Wheel Base: 71″ Extended 4.5″ At Rear Axel Wheel Base w/EZ Steer 72.5″ Load Capacity: 500 Lb Tire Size: 205 / 70 / R15 Wheel Size (15″) Offset +35 mm 15x7JJ 4×4.5 Tire Pressure 20 PSI Suspension: “Zero-Flex” Internal Swing Arm utilizing 3 shocks, OEM shock absorber plus 2 coil over shock absorbers. Rear Differential: Champion Lightweight rear axle / differential assembly. Gear Ratio 2.93:1 gear ratio Brakes: Original front plus 2 high performance disc brakes at rear. Storage Capacity: 6.75 cubic feet. 3 full-face helmets and additional storage. Trike Conversion Installation Kit Honda Goldwing GL1800 Champion Trikes Page 7 of 28 Revision 10 4 Removal of Original Parts Most tasks necessary in this guide can be accomplished with the vehicle on its center stand. Secure the center stand to one of the forward crash bars with a ratchet strap to keep vehicle from rolling forward and off the center stand. Be sure that the vehicle is laterally stable as well. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for return of deposit or re-installation after modification shall be duly noted. • Seat (to be re-installed without modification) • Left and right side covers (to be re-installed without modification) • Battery and battery box (to be re-installed without modification) • Left and right saddle bags • Remove taillight and locking assemblies from saddlebags (to be returned for refund of deposit) • Trunk (to be re-installed without modification) • Left and right passenger foot rests (to be re-installed without modification) • Left and right foot rest under covers (to be modified and re-installed) • Left and right rear crash bars • Saddle bag trunk stay (to be modified and re-installed) • Left and right mufflers (Mufflers only, do not remove decorative covers) • Rear wheel • Left and right pivot bolt covers (to be re-installed without modification) • Reverse resistor (to be relocated) • Swing Arm – Note : Carry out brake system modifications (Section 5) prior to removing Swing Arm. • Note : Upper bolt of mono shock can be removed without removing the fuel tank. • Note : Do not remove actuator hose from actuator pump or shock absorber. Dismounting shock actuator pump will allow more movement of shock absorber when removing swing arm.Trike Conversion Installation Kit Honda Goldwing GL1800 Champion Trikes Page 8 of 28 Revision 10 5 Brake System Modification Note : Modification to the vehicle brake system should be carried out prior to removal of the swing arm. From the manufacturer, your Honda Gold Wing brake system utilizes both front and rear brakes when the foot brake is applied. In order to insure safe operation of your Gold Wing when converted to a Champion Sidecars Trike, the brake system must be modified to isolate the front and rear brake systems from each other. Once modification is complete, four of the six pistons in the front calipers operate only when the hand brake lever is applied. The rear brakes operate only when the foot brake pedal is applied. The diagrams below outline the difference between the GL1800 OEM brake system and the system as modified by the Champion Sidecars Trike Conversion Kit.

Incoming search terms:

Harley-Davidson FLH Series 2008 and Down, Independent Suspension Trike Conversion Installation Manual

0

Filed Under (Harley Davidson) by admin on 07-03-2012

download
Protect yourself and others when you have a vehicle up in the air. Anytime you lift a vehicle, either by hoist or a jack, make sure that it is securely supported. b. Make sure the engine is turned off and battery disconnected before you begin work.  Carbon Monoxide poisoning from exhaust gases: Be sure there is adequate ventilation whenever you run the engine.  Burns from hot parts: Let the engine and exhaust system cool before working on those areas.  Injury from moving parts: If running the engine, keep hands, fingers and clothing away from moving/rotating parts. c. Gasoline vapor and hydrogen gases from batteries are explosive. To reduce the possibility of fire or explosion, be careful when working near gasoline and batteries. d. Use only nonflammable solvent, not gasoline, to clean parts e. Never drain or store gasoline in an open container. f. Keep all cigarettes, sparks or flame away from the battery and all fuel related parts. 1.5 Specifications Overall Length: 103″ Overall Width: 57.25″ Wheel Base: 53″ Load Capacity: 600 Lb Tire Size (15″): 205 / 70 / R15 Wheel Size (15″) (4 lug) Offset +35 mm 15x7JJ 4 on 4.5 Tire Pressure: 24-26 PSI Suspension: Double A-arm Independent Rear Differential: Custom-built rear differential utilizing OEM drive belt. Brakes: Original front plus 2 high performance disc brakes at rear. Storage Capacity: 5.75 cubic feet. Two full-face helmets and additional storage.
Harley-Davidson® FLH 2008 & Down Independent Suspension CHAMPION TRIKES Installation Guide Page 6 of 20 Revision 4 2 Removal of Original Parts Secure and raise motorcycle 9 to 10 inches using a quality motorcycle lift. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for reinstallation after modification are noted.  Seat – to be re-installed; without modification.  Left and right side covers – to be re-installed after modification.  Tour Box – to be re-installed (if so equipped).  Left and right saddle bags (if so equipped).  Left and right rear crash bars, saddlebag rails (if so equipped).  Tour Box mounting frame (if so equipped).  Left and right passenger foot rests – to be re-installed without modification.  Left and right mufflers  Rear wheel NOTE: Prior to removing rear wheel, depress foot brake and secure in down position (e.g., zip-tie to floor board). This will prevent fluid flow when rear brake Caliper is removed.  Remove Rear Caliper (disconnect brake line at Caliper). NOTE: Cap line to prevent introduction of dust / debris into line. Remove Caliper