process for tightening front primary pulley 2000 electra glide

You search Auto repair manual PDF process for tightening front primary pulley 2000 electra glide, if there are search results will appear below. If search results do not exist, please search by others keyword.



  process for tightening front primary pulley 2000 electra glide Direct Download speed 5282 Kb/s

  process for tightening front primary pulley 2000 electra glide Full Version speed 6162 Kb/s



Harley Davidson FL series Electra Glide, Ultra Classic, Road King, Road Glide Left and Right Mounting Plate Installation Installation Manual

0

Filed Under (Harley Davidson) by admin on 25-02-2012

download
Remove existing control arm end cap and grind the outside flush. See picture below for reference. The swing arm will drop if both sides are removed at the same time. To ease installation, complete one side before starting on the other. Note: there is a left and right. Left and right end caps shown. 2. Install mounting plate assembly 10002351 on top of the end cap using 7/16″ hex head bolt and lock washer in the bottom hole. Use the 7/16″ counter sink bolt in the top hole. Make sure the end cap is seated properly. The end cap notch should fit into the recess on the frame. The pivot arm assembly is shipped on mounting plate assembly; you may remove the pivot arm to make installation easier. 3. Snug up the bolts evenly, make sure the end caps are not crooked in relation to the frame. Tighten both bolts to 25 ft lbs. (Further tightening will be required after the toe in is set). 4. If you removed the left hand pivot arm assembly, remount it now, 10002575-A (pg 20) with seal, bearings (2), washer, nut, cotter pin and dust cover. 5. Repeat for right hand side. 5 Toe In Adjustment Adjustment made with the mounting plates, bolts, pivot arms, and hubs (without wheels and tires) in place

HARLEY DAVIDSON CHROME INNER PRIMARY HOUSING INSTALLATION INSTRUCTION

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
Kit Contents Table 1. Kit Contents Part Number Description (Quantity) Not sold separately Chrome Inner Primary Housing 786A Sealing fastener (5) INSTALLATION NOTES Whenever the sealing fasteners are loosened or removed, they must be replaced. Always replace using Harley-Davidson® Original Equipment sealing fasteners part 786A. Do not use part 786. The primary housing included in this kit installs in the same manner as the stock inner primary housing with the following exception: Use the five sealing fasteners included with this kit. Install and tighten fasteners to the torque specified below. For 2006 Dyna model motorcycles: Remove dowel pins from the chrome inner primary housing before attempting installation. Using a pair of pliers or vice grips, remove the dowel pins by carefully twisting and pulling on the pins. Be careful not to scratch or mar the chrome or sealing surfaces of the chrome inner primary housing. Remove the chain tensioner anchor plate, bolt and screws from the stock inner primary housing after it has been removed, then install it on the chrome inner primary housing. See the appropriate Service Manual for the proper tightening procedure, and torque specifications. 1. See the Drive section of the appropriate Service Manual, and remove the stock inner primary housing. Clean the internal threads in the crankcase and transmission case where the sealing fasteners were removed using a wire brush. Install the chrome inner primary housing as indicated below. Replace the five stock sealing fasteners with the five bolts included in this kit. Put a light coat of primary oil under the head of the sealing fasteners and then tighten to 23-25 ft- lbs (31-34 Nm)

Incoming search terms:

HARLEY DAVIDSON BLACK ENGINE GUARD KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
REMOVAL NOTE This Instruction Sheet covers several different Harley-Davidson models and years. Be sure to locate and follow the procedures that apply to the motorcycle receiving the new guard. For Models without Lower Fairings 1. Proceed to For All Models section. For Model FLHTCUI (Ultra Classic Electra Glide) with Factory-Installed Lower Fairings 1. Remove the lower fairings following the instructions in the appropriate Service Manual. 2. When the lower fairings have been removed, proceed to For All Models section. For Models FLHR/I (Road King), FLHT (Electra Glide Standard) or FLHTC/I (Electra Glide Classic) with Harley-Davidson Genuine Motor Accessory Lower Fairings 1. See Figure 1. Remove the two black screws (1) that attach the fairing cap (2) to the lower fairing (5). Remove the cap. Set the parts aside for re-installation. 2. Remove the screw (7), rubber washer (8) and locknut (10) and the clamp (9) that attaches the bottom of the lower fairing to the engine guard and set aside. 3. Remove the two locknuts (3), U-bolt (6) and U-bolt retainer (4). 4. Remove the lower fairing by sliding it out from behind the engine guard. 5. Repeat Steps 1 through 4 for the opposite side. 6. Proceed to For All Models section. For Model FLTR/I (Road Glide) with Harley-Davidson Genuine Motor Accessory Lower Fairings Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the battery, negative (-) battery cable first, following the instructions in the appropriate Service Manual. 2. Remove the seat following the instructions in the appropriate Service Manual. 3. Remove the cable strap holding the clutch cable to the engine guard. 4. See Figure 2. Remove the TORX screw (8), rubber washer (9) and locknut (11) and the clamp (10) that attaches the bottom of the lower fairing (4) to the engine guard and set aside INSTALLATION 1. Hold the engine guard in position, and loosely fasten the top of the guard with the new hex socket screw and flat washer from the kit. 2. Install the bottom brackets to the motorcycle frame with the two new TORX screws and locknuts. 3. Tighten all three screws to 15-20 ft-lbs (20.3-27.1 Nm) . For Model FLHTCUI (Ultra Classic Electra Glide) with Factory-Installed Lower Fairings 1. Install the lower fairings following the instructions in the appropriate Service Manual. For Models FLHR/I (Road King), FLHT (Electra Glide Standard) or FLHTC/I (Electra Glide Classic) with Harley- Davidson Genuine Motor Accessory Lower Fairings 1. Carefully place one lower fairing in position from behind the engine guard. 2. See Figure 1. Install the lower fairing to the top of the new engine guard with the U-bolt (6) from the back, through the holes at the top of the fairing. Install the retainer (4) in position on the U-bolt and secure to the engine guard with the two locknuts (3). Do not tighten the locknuts at this time. 3. Attach the bottom of the fairing to the engine guard with the clamp (9) removed earlier. Install the clamp around the engine guard in the direction shown, with the tabs toward the rear of the vehicle and the flat side of the clamp against the lower fairing. Insert the screw (7) through the lower fairing, rubber washer (8) and clamp (9). Secure the assembly with the locknut (10). Tighten to 12 ft-lbs (16.3 Nm) .

Incoming search terms:

HARLEY DAVIDSON FLHT (Electra Glide Standard) FAIRING COMPARTMENT POUCH INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 31-03-2011

download
General This kit is designed for 1996 and later FLHT, Electra Glide Standard, model motorcycles Kit contents: QTY DESCRIPTION 1 Pouch 4 Velcro™strip Installation 1. Wash inside of fairing compartment with a clean, soft, nonabrasive cloth, water and mild soap. 1 CAUTION DO NOT use benzine, paint thinner, gasoline, powdered abrasives, alkaline cleansers, or any other harsh cleansers to clean the fairing compartment. They will damage the surface. Never scrape fairing surfaces with a razor blade or other sharp instrument because permanent damage will result. 2. Arrange pouch in compartment. 3. Align and attach velcro strips from kit to top, bottom and sides of compartment so they match the placement of velcro strips on pouch. 4. To secure pouch to fairing compartment, press pouch velcro strips against compartment velcro strips. Care of Pouch 1. When necessary, remove and wash pouch with mild soap and warm water

HARLEY DAVIDSON DETACHABLE TOUR-PAK KIT FOR ELECTRA GLIDE CLASSIC INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
INSTALLATION Install Docking Kits and License Plate Holder 1. Install Rear Detachable Docking kit. Refer to the instruction sheet provided with kit. 2. Install Touring Detachable Tour-Pak Rack. Refer to the instruction sheet provided with kit. 1 4 2 3 is03989 1. License Plate Holder 2. Red Reflector 3. Original Equipment Screws 4. Original Equipment Bottom Support Tube Figure 2. Install License Plate Holder 3. See Figure 2. Install the new license plate holder (1) to the bottom support tube (4) using screws (3) saved from prior step. 4. Remove adhesive backing from red reflector (2) and carefully center and align it with the bottom edge of the license plate holder (1) and press firmly into place. -J03930 1 of 4 MOUNTING ANTENNA RELOCATION BRACKET 1. See Figure 6. Assemble joint assembly (9) to antenna mounting bracket (6) using lock washer (5) and 2 hex nuts (4). Tighten hardware securely. 2 1 5 4 3 is03992 1. Rear Docking Point 2. Docking Point Support Bracket 3. Antenna Mounting Bracket 4. Antenna/Cable Adapter 5. Rear Docking Point Screw and Locknut Figure 3. Relocated Antenna Bracket and Cable 2. See Figure 3. Install assembled antenna bracket (3) by removing screw and locknut (5) securing left rear docking point (1) to docking support (2). Install bracket as shown and reinstall rear docking point screw and locknut. Tighten screw and locknut to 15-19 ft-lbs (20.3-25.7 Nm) . 3. Thread antenna/cable adapter (4) onto joint assembly. ROUTING ANTENNA CABLES 1. See Figure 4. Gently remove left side cover (1) by pulling from frame tubes (no tools required). 2. Connect original antenna cable (not shown) to bottom of joint assembly. 3. Route antenna cable/wiring between left frame rail and fender. 4. See Figure 5. Attach cable to docking point support bracket in location (1) using short cable strap. 5. See Figure 4. Coil excess antenna cable/wiring (2) and use long cable strap (3) to fasten cable to frame under left side cover (1) with vehicle wiring harness. 6. See Figure 6. Cap unused wiring connector with connector housing (10).

HARLEY DAVIDSON ULTRA CLASSIC AND ELECTRA GLIDE CLASSIC TOUR PACK ADJUSTMENT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 23-04-2012

download
1. Open the Tour Pack and remove all of the contents. 2. Remove map bag and inner pack liner. Pack liner comes out quite easily once map bag is removed. 3. Remove the 4 bolts inside the tour pack that are located on top of the metal support plate that hold the tour pack to the luggage rack. Have your assistant hold the pack in place before removing the last bolt. 4. Gently tip the tour pack forward to expose the supporting luggage rack under the pack. 5. While your assistant holds the pack up, place the two adjusting bars on top of the supporting luggage rack. Use the 4 flat head screws supplied with the kit to mount the bars snugly to the support rack (see fig. 1). 6. Reposition the tour pack over the threaded holes in the adjusting bars at the 2″ or 3″ position and bolt it in place snugly (see fig. 2). 7. Replace the trunk liner and map case and the installation is complete

Incoming search terms:

Harley-Davidson Electra Glide LED Motorcycle Lightbar Installation Guide

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
Mounting IMPORTANT! The lightbar should be located a minimum of 16″ from any radio antennas! This product is designed to mount in the lowest, visable section of the motorcycle windshield. The mounting procedure requires removal of the front facia panel of the motorcycle. 1. Remove the 3 screws along the base of the windshield from the upper section of the faring facia panel. 2. Remove the 4 remaining screws (shown above) that secure the facia panel to the faring. With these screws removed, the facia and windshield can now be removed from the motorcycle faring. 3. Position the lightbar into its mounting position. The base of the lightbar fits onto the three screw bosses used by the screws removed in step 1. 4. With the facia panel removed, the lightbar should now be wired. 5. Route the wires to their respective destinations. It is left to the installation technician’s discretion to select a path for these wires that will both protect them from possible damage and not interfere with the operation of any other vehicle components or equipment. 6. Using the original hardware removed in steps 1 & 2, remount the faring and windshield according to the motorcycle manufacturers service manual

1937-1984 Big Twins BRUTE II EXTREME BELT DRIVES INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 27-10-2010

download
Remove the outer primary cover. Remove the front pulley, chain, compensator & chain adjuster Remove oil lines to primary and plug or clamp to prevent leakage. Cut the chain oiler hose 3 inches from the oil pump and permanently plug. All belts must be run dry without lubrication of any kind. Therefore, remove all oil from inside the primary covers. The spacer behind the front pulley should be removed prior to installing the belt drive. This spacer may or may not be required to correctly align the pulleys. If a spacer is needed for alignment, various sizes are available from your local Primo Belt Drives dealer (part number PX-1 =package of 6 various sizes). Install the front pulley supplied in the kit. Loop the belt around both pulleys to insure that you have the proper belt for your pulleys, then gently push the unit into place. Use the supplied washer & nut on the motor shaft. Torque the motor nut to 80-100 foot pounds. If installing a PC-1000-Aremove the clutch hub & clutch basket. On tapered shaft models check the fit on the shaft & the fit of the keyway in the hub. Install the key in the mainshaft, making sure it is firmly seated (use of super glue or threadlock in the keyway is helpful to keep the key from sliding out of the keyway during clutch installation). Tighten the clutch hub nut(left-hand thread) to 60-90 foot pounds. 1 After installing and adjusting clutch, track the belt by turning the pulleys. If needed use a straight edge between the front and rear pulleys to check alignment. Improper alignment of the pulleys will result in reduced belt life. Spacing the motor pulley outward will cause the belt to track towards the outer primary cover. If spaced too far out the belt will rub on the inside of the clutch shell. Before installing the primary cover be sure that everything inside clears both the outer and inner covers. In some cases a small amount of metal may need to be removed from one or more of the bosses on the inner or outer primary cover.

Installation Instructions for TRD’s 3.4-liter V6 Supercharger Kit 1997-2000 Tacoma,1997-1998 T-100, 1996-2000 4Runner

0

Filed Under (Toyota Manuals) by admin on 28-05-2011

Download

begin, TRD recommends you thoroughly Before you and engine compartment.thatyou don’t, grease clean the engine
If buildup  on parts could become dislodged during the procedure and fall into the engine.
• Make sure the engine has cooled fully before you begin. suggest you draw diagrams of your
• To help you later, we you disconnect anything. You can doengine’s cable routing before the same

for the vacuum hoses; however, some of the vacuum connections on your stock manifold may not be the same as those on the supercharger. To ensure the proper hose connections, refer to the diagrams in the back of this manual.
TRD supercharger has been designed to reuse most of • Thestock nuts and bolts.kitTherefore, as you remove them, keep the  them with their components or label them for location. This will assure a faster, easier installation.
B. Removal of Stock Intake Manifold (figure 1)
1. Disconnect the battery ground cable.
2. With tape or a permanent marker, mark the forward edge of the power steering and the air conditioning compressor drive belts (figure 2). This will ensure that the belts will be returned to their original positions and that they will rotate in the same direction. If you reverse the direction of rotation, it may cause the belts to fray.

Short Shift Kit 2000 and up Toyota Celica 2000 and up MR Spyder Installation Manual

0

Filed Under (Toyota Manuals) by admin on 30-05-2011

Download
Step 16: Use the cup remover tool included with the kit to remove both plastic cups on the original shifter. To do so, place the cup remover tool on top of the open jaws of a vice, the jaws should be approximately 1” apart. Hang the shifter from the tool as shown, be sure the shifter is inserted completely into the slot in the tool. Insert a punch into the center hole through the plastic cup and tap firmly with a hammer to separate the original shifter from cup. Repeat for 2nd cup.Re-Installation Install the plastic cups which you removed from the original shifter onto the TWM shifter. Grease the cups and pivot balls. Place the cup on a firm surface and push the TWM shifter into it until it pops in

Incoming search terms: