kubota rtv 900 front hub assembly

You search Auto repair manual PDF kubota rtv 900 front hub assembly, if there are search results will appear below. If search results do not exist, please search by others keyword.



  kubota rtv 900 front hub assembly Direct Download speed 5282 Kb/s

  kubota rtv 900 front hub assembly Full Version speed 6162 Kb/s



HARLEY DAVIDSON FRONT THUNDERSTAR WHEELS INSTALLATION

0

Filed Under (Harley Davidson) by admin on 08-11-2010

download
Remove existing front wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to FRONT WHEEL in service manual. For FLSTC and FLSTN Models: Discard moon-style hub cap. -J04065 1 of 8 For FXSTD Models: Discard the tapered r ight side wheel spacer. Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c) NOTE • For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771- 07, 43609-07, 44323-07, 44282-07, 44322-07, 43975-07, 43602-07 and 43773-07 install short valve stem (43157- 83A) included in the installation kit. • For Kits 40943-09, 40966-09 and 40996-09 install long valve stem (43206-01) included in the installation kit. 2. See Figure 2. Install valve stem assembly (L, M or N) on wheel. Refer to TIRES in service manual. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in Service Manual. NOTES Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771-07, 43609-07, 40943-09, 40966-09 and 40996-09: • The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and/or DOT markings to identify it as the brake disc and primary bearing side. • Install the wheel so that the valve stem is on the right side of the motorcycle. For Kits 44323-07, 44322-07 and 44282-07: • Install the wheel so that the hub markings are on the left side of the motorcycle. The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and hub markings to identify it as the primary bearing side. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). • The gross axle weight ratings is unaffected by the installation of this wheel on a vehicle equipped with a 21-inch wheel. For Kits 43975-07, 43773-07, and 43602-07: • The wheel has a machined groove (item 5, Figure 2) in the hub face to identify the right side. • For 2007 and later FX Softail Models and 2008 and later FXDWG: The left side of the wheel is the primary bearing side. For all other models the right side of the wheel is the primary bearing side. • For Kit 43602-07: An arrow is engraved into the right side hub to indicate the direction of rotation. • For Kits 43975-07 and 43773-07: An arrow is cast between the spokes on the right side to indicate the direction of rotation. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake-disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). 4. Install wheel assembly parts from the appropriate Service Parts table for this fitment and stock brake disc. Discard parts from the installation kit that are not required. Refer to FRONT WHEEL in Service Manual. 5. For FLSTC and FLSTN Models: Install wheel kit and right side wheel spacer provided in installation kit. For FXSTD Models: Install wheel kit, stock left wheel spacer and right side wheel spacer from installation kit in place of the tapered right side wheel spacer discarded in Step 1. Refer to FRONT WHEEL in service manual. For FXSTS Models: Install the left side wheel spacer provided in the kit between the stock left wheel spacer and the left fork. All other models: Install wheel spacers previously removed. 6. Install front wheel (1), stock axle and stock axle nut. Refer to FRONT WHEEL in service manual

Incoming search terms:

Honda 400EX Hub installation instructions

0

Filed Under (Honda) by admin on 20-12-2011

download
Remove all contents from its packaging and verify that all parts are present and free from damage. You should have the following items: (2) wheel hubs (2) smaller tapered bearings (2) large tapered bearings (2) wheel bearing nuts (2) dust caps (2) inner bearing seals (6) M3 x .5 screws (2) cotter pins (2) inner bearing spacers 2. Completely remove the old hubs from your quad and clean the spindle and the surrounding areas. It is very important to keep the new bearings and seals clean during installation for long life. Be sure to remove the factory inner bearing spacers from the spindle and discard. They will not be used in re-assembly. 3. Pack your new Timken tapered wheel bearings with a liberal amount of high quality wheel bearing grease. A wheel bearing packer works best, however you can accomplish the task by placing the grease in the palm of your hand and manually working it in between the bearing rollers. We also recommend that you pack the area between the bearing races in the hub with grease for additional lubrication and protection against moisture. 4. Place the large wheel bearing (inner) into the hub and install the inner seal. The seal should bottom out against the step in the bore and the face should be flush with the hub. 5. Remove the brake rotors from your old hubs. Re-install the rotors on your new hubs and be sure to use medium strength Loctite on the threads. 6. Apply a light film of grease or oil to the large diameter of the spindle stud. Install the new o-ringed bearing spacer onto the spindle. 7. Apply a thin film of grease to the seal surface on the bearing spacer and the inside diameter of the seal to prevent the seal from running dry. Install the hub onto the spindle and slide the outer bearing over the spindle and install the new bearing nut furnished with your hubs. Do not use the factory nut or washer. 8. SETTING THE BEARING PRELOAD: It is first necessary to seat the bearing before setting the preload. This aligns the rollers and prevents the bearings from loosening after a short period of use. To seat the bearing, tighten the spindle nut while you rotate the hub until the hub becomes difficult to spin. With the bearing now seated, you must set the bearing preload. Preload means placing a small amount of force against the bearings to remove any clearance between the bearing race and the rollers. This is done by backing the nut off completely and re-tightening it with your fingers. Do not rotate the hub while setting the preload . If a hole in the spindle is not accessible for installation of the cotter pin, adjust the nut tighter to bring a hole into alignment. Install the cotter pin and bend the pin around the outside of the nut. Do not attempt to bend the pin toward you (over the end of the spindle) or it may rub on the inside of the dust cap.

Incoming search terms:

AJS DISMANTLING AND REBUILDING FULL-WIDTH FRONT WHEEL HUBS INSTALLATION

0

Filed Under (AJS) by admin on 31-10-2010

download
Removal of the Brake-side Bearing Cup The bearing cup (5) is located endwise by a circlip (1), and between the cup and circlip arc an oil-seal retaining washer (4), oil seal (3), and oil-seal cup washer (2) Before these parts can be removed from the hub the bearing cup must be moved inwards for a very short distance (3/16-inch) so that the circlip can be withdrawn. (n) Gently heat the hub shell. (i) Place a soft metal rod (e.g. brass) against the oil-seal cup washer (2) and apply pressure with a hand press or hammer blows. It is only necessary to move the bearing cup (5) inwards about 1/16-inch. (j) Extract the circlip by inserting a narrow pen-knife blade under one end of the circlip; lift it upwards and outwards and prise the clip out of its groove. (k) Remove the oil-seal cup washer (2), oil seal (3) and oil-seal retaining washer (4). They can be hooked out with the shank of a small and narrow screw­ driver, (l) The bearing cup can now be ejected by placing a suitable rod of soft metal (e.g. brass) in the hub tunnel from the right-hand side and pressing it — with a press or hammer blows — against the bearing cup until the cup is forced out of the bearing. This must be done with care so that the cup remains square with the housing. Reassembly To facilitate replacement of the bearing cups gently heat the hub shell. Just too hot to hold is about the right temperature. (a) Place the brake-side bearing cup squarely in the hub shell — the open end faces inwards — and press it into the hub tunnel A short length of brass rod, slightly less than the outside dia­ meter of the cup, should be interposed between the cup and ram of the press, or hammer head. Press the cup in until the outer face is approximately half-an-inch below the mouth of the hub tunnel. This will allow sufficient room to allow [he circlip to be inserted into its groove. (b) Refit in the following order: oil-seal retaining washer (4), oil seal (3), oil-seal cup washer (2). (c) The circlip can now be replaced. In the interest of reliability use a new circlip, for it is possible that the existing circlip was strained when it was re­ moved. (d) Insert into the hub tunnel from the right-hand side a brass rod of suitable length, and press the bearing cup firmly against the circlip. (e) Before inserting the spindle complete with the roller races, pack them with clean and fresh grease of a suitable grade (Mobilgrease No. 4. Castrolease heavy, Energrease C3, Esso Pressure Gun Grease. Shelf Retinax Grease CD or A). (0 Insert the spindle into the hub. (g) Place the right-hand side bearing cup in the hub tunnel; the open end faces inwards, It may be necessary to re-heat the hub to allow the cup to go into position without difficulty. (h) Press the cup into position, but do not force it fully home, leave some end play on the spindle. (i) Refit in the following order: oil-seal retaining washer (6), oil-seal (7) and oil-seal cup washer (8). (j) Screw into the hub the adjusting sleeve (9) until it comes into contact with the bearing cup (5)

DUCATI EVOLUZIONE SLIPPER CLUTCH KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Ducati) by admin on 25-10-2010

download
If installing with Ducati OEM basket you need the washer cod. 0D1SR140C220045 (3mm). – If installing with STM basket (Z12 o Z48) you need the washer cod. 001MG019 (1,5mm). – Insert the correct washer on the gear shaft. – Perform the initial hub group assembly: position the progressive engagement steel plate (003MG015) on the hub (0F3SR140J24001C) , with the step facing up. Be careful to position it correctly into the specific seats, then check that pushing one side, the opposite stand up simultaneously. – Now put the 6 steel balls (001MG025) at the bottom of the grooves using a little bit of grease. Then fix the clutch drum (0F3SR140J24002C) on the clutch hub (0F3SR140J24001C) at rest position, using an M6 screw to help locking the two parts, avoiding in this way any possibility for the steel balls (001MG025) to fall out while inserting the hub pack on the main shaft. – Insert the hub pack on the gear shaft – Insert the clutch discs starting with the sintered one and finishing with the steel guided one; total disc set thickness must be included between 36 and 36,5mm. – Remove the M6 screw from the hub (0F3SR140J24001C). – Put the drum stopper hub (003MG106) on the hub (0F3SR140J24001C). – Verify that the secondary spring support (0F3SR540B140016) is well inserted into its housing on the drum (0F3SR140J24002C). – Insert the secondary spring (0S2085) into its housing on the drum (0F3SR140J24002C). – Mount the pressure plate (003MGP10) on the drum (0F3SR140J24002C) . – Position the Evoluzione spring (0S1090) on the pressure plate (003MGP10), with the convex part facing up (STM logo facing up), making sure previously that the squared section ring (901SE003), which works as primary spring support, is well positioned into the pressure plate itself. – Assemble the complete spring stopper pack: starting from the spring stopper plate (003MG008), with the shaped side facing up as shown in the picture. Insert the ball bearing (003MG007) and finally the spring stopper hub (0F3SR140N220007). Once completed these operations, position the complete spring stopper pack inside the Evoluzione spring (0S1090). – Insert the toothed washer (901RD101) with the convex side facing up, then insert and tighten up the clutch nut (0F30S140C220013); use a dynamometric wrench setting the torque suggested by the bike manufacturer. We suggest to use the specific optional tool (UTL-0020) in order to lock the pressure plate (003MGP10) while performing this operation. – Assemble the complete bearing rest pack: insert the washer (001MG018) in its housing on the bearing rest (0F3SR140N220004). Then put in the same housing the ball bearing and the push rod pin of the original clutch. – Position the complete bearing rest pack in the pressure plate (003MGP10), making sure it fits correctly into the housing grooves. – Manually practise a little pressure on the bearing rest (0F3SR140N220004) in order to release the seat for the tightness circlip (003MG018). – Fit correctly the above mentioned tightness circlip (003MG018). MAKE SURE that it adheres to all the groove perimeter. NB: Once completed the installation, repeatedly operate the clutch lever, checking that the pressure plate performs correctly the opening and closing movements. For a road use of the clutch you have to check clutch plates set every 2000 km. Please verify that the clutch plates set thickness is between 36,5mm and 35,0mm. If it is inferior to 35,0mm please replace a 1,5 steel plate with a 2 mm steel plate. For a racing use of the clutch we suggest to check the clutch plates set thickness frequently. GENERAL SAFETY REGULATIONS – In this sheet are reported the directions to perform correctly the clutch assembly operations. – STM reserves the right – without notice – to introduce any technical change whenever deemed it to be necessary to improve functionality and quality of the products. – Assembly operations must be performed by a skilled technician and must be scrupulously observed. – Before mounting the clutch make a complete inspection of the various parts, in order to verify the possible presence of faults or anomalies on the motorbike. – Make sure that there are no missing/damaged parts in the package . – Some parts of the clutch and its components can have sharp surface: handle with care. – Some components of the clutch, because of their small dimensions can be swallowed: keep away from children. STRADA srl Via Campo Archero 20 10023 Chieri ( TO ) Tel +39 011 9422832 Fax +39 011 9471447 003 MG 018 Tightness circlip

Harley Davidson Softail Drive Side Brake System Installation Manual

0

Filed Under (Harley Davidson) by admin on 30-03-2012

download
Removing The Stock Components Although the PM Drive Side Brake System can be installed with the swing arm bolted to the frame, we recommend removing it for better access as well as repainting. Begin by removing rear wheel,stock brake components and belt guard from swing arm. Photo #1 Using supplied 3/4 x 2″bolt,position Drive Side BrakeAssembly on swing arm. Slide assembly to center position of tab and axle spans. Making sure brake mounting tabs are flush with swing arm,snug 3/4 x 2″ bolt to hold assembly and mark swing arm area to be ground Photo #2 . Remove entire assembly from swing arm and thoroughly grind paint away from marked areas Photo #3 . Photo #4 Re-mount assembly to swing arm and slide to rear-most position of both axle and brake mounting tabs. Confirm that brake tabs are flush with swing arm and parallel to each other. Snug 3/4 x 2″bolt and 5/16″socket head cap screws in tabs to hold assembly during welding process. Warning Center the motorcycle on the lift so that it will not fall while you are working on it. Photo #6 Photo #5 Photo #7 Photo #9 Welding Tabs to Swing Arm Note PM recommends all welding be done by a certified welder. Photo #5 Tack weld rear of tabs to swing arm. Avoid excessive welding near brake as- sembly as heat can mar finish. Loosen socket head cap screws and 3/4″bolt,Slide entire assembly to forward most position and re tighten bolts Photo #6 (movement should require minimal effort if tabs are aligned properly) and tack front of tabs to swing arm. Remove brake assembly from swing arm. Weld tabs to swing arm.Verify alignment of tabs, as they must remain parallel to each other. Repaint swing arm and re-install on bike to factory torque specs. Installing Brake Assembly Remove primary bracket from tower assembly (this allows bracket to be installed without having to line up caliper on disc) by removing the three 5/16″socket head cap screws (commonly called allen bolts). Photo #7 Mount rear tire and bolt pulley to rear wheel. Place disassembled bracket against pulley using smaller of two supplied spacers between bracket and pulley. Slide wheel/brake assembly into swing arm. Place large spacer on right side and slide axle in. Do not tighten axle at this point . Photo #8 Slide caliper/tower assembly over disc and install 5/16″x 1″socket head cap screw in center hole to position assembly Photo #9 . Snug, but do not tighten bolt at this point.

Incoming search terms:

HARLEY DAVIDSON FRONT DETONATOR WHEELS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
INSTALLATION 1. Remove existing front wheel assembly. Save axle, axle nut, brake disc and wheel spacers for kit installation. Discard moon-style hub cap on FLSTC and FLSTN models. Discard left side spacer on FXSTS models and tapered spacer on FXSTD models. Refer to FRONT WHEEL in Service Manual. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) 2. See Figure 1. Install valve stem assembly (D) on wheel. Refer to TIRES in Service Manual. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in Service Manual. NOTE Install primary bearing first using the applicable Service Manual and WHEEL BEARING REMOVER/INSTALLER. Kit 44550-07: The left side of the wheel has a groove machined in the hub to identify it as the disc side for installation, as well as the primary bearing side. The wheel should be installed so that the valve stem is on the right side of the motorcycle. Kits 44660-07 and 44661-07: The wheel should be installed so that the hub markings are on the left side of the motorcycle. An arrow engraved into the rim of 44661-07 indicates the direction of rotation. A groove is machined in the left-side hub face to indicate the primary bearing side. • Dual-disc models: Install the brake discs according to the Service Manual procedures. The Chrome hub cap (2) is not used. • Single-disc models: Install the brake disc according to the Service Manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Kit 44660-07: The gross axle weight rating is unaffected by the installation of this wheel on a vehicle originally equipped with 21-inch wheels. Kit 44661-07: The gross axle weight rating is unaffected by the installation of this wheel on a vehicle originally equipped with 19-inch wheels. Kit 44552-08: The left side of the wheel has a groove machined in the hub to identify it as the left side for installation, as well as the primary bearing side. The wheel should be installed so that the valve stem is on the right side of the motorcycle. Kit 44556-07: The right side of the wheel has a groove machined in the hub to identify it as the right side for installa

Victory Vegas Rear LED Turn Signal Assembly Installation Manual

0

Filed Under (Victory) by admin on 31-10-2010

download
Step 1 •Prior to installation it is recommended that you perform a Pre-Function check. To do so, remove the left side battery cover from the bike and expose the post terminals. Hold the positive red lead from the turn signal to the positive red lead of the battery and then place the negative black lead from the turn signal to the negative black lead of the battery. Do one side at a time and ensure that both sides light prior to installation. Step 2 •Remove seat (passenger too if installed) •Remove fender “eyelashes” (required first if passenger seat is installed) •Remove the fender mounting bolts •Disconnect the rear turn signal and taillight harness connector located in the battery box compartment •Remove the fender by gentle prying outward and upward on one side to clear the mounting points, then the other side •Set aside on a flat and smooth surface to protect the fender’s finish (you may want to wrap it in a large towel) Step 3 •Turn the rear fender assembly upside down on a stable and covered/protected surface to prevent damaging the fender/paint •Remove the rear tail assembly and disconnect the wiring harness and license plate light. THIS PART IS NO LONGER NEEDED! Victory Vegas Rear LED Turn Signal Assembly Installation Guide •Remove the stock metal spacers shown below and replace them with the ¼” rubber spacers included in your accessory/installation kit. Step 4 •Place the turn signal assembly mounting arms over the rubber spacers. Align the turn signal in place so the space between the fender and the turn signal tube is consistent. After completing this step, place a small amount of Loc-Tite to the bolt and slowly tighten the stock nuts snugly in place, (extreme over-tightening may damage turn signal or fender lip). You should not need to loosen the mounting arms which are attached to the turn signal bracket to obtain the ideal fit; they are pre-assembled to be aligned. Please also note that due to manufacturing tolerances in the production of the fender, the rolled inner lip of it may interfere with the turn signal assembly seating properly. If this is the case, the lip can be tapped down flush with a rubber mallet or other appropriate tool. Take the necessary precautions to maintain your fender’s finish should this step be necessary. Step 5 •Run the wiring of the turn signal assembly in an appropriate/desireable path to the stock wiring harness. See picture below as an example. Once the wires are run, cut any excess wire and install the bullet connectors (included in the installation/accessory package) to the end of the wires. Due to the small gauge of the wire it’s suggested that you double it over before placing it into the bullet connector and solder it in place. Wire as follows:

ESCAPADE TRAILER Wheel Bearing Removal AND OWNER'S MANUAL

0

Filed Under (Tips and Review) by admin on 20-11-2010

download
1. Remove lug nuts and wheel assembly. Remove the cotter pin, adjusting nut (castle nut) and washer from the wheel spindle. 2. Pull the wheel hub towards you to loosen the outer bearing cone. Don’t Let the cone fall to the ground. As the hub is removed, the inner bearing and grease seal will come with it. Observe which direction the inner seal is facing. Pry out the inner seal and discard. 3. Remove all old lubricant from the hub assembly and wheel spindle with kerosene or mineral spirits. CAUTION: do not use gasoline to clean and remove the old lubricant). Inspect the spindle for scoring, bending, thread or other damage. A light grease coating on the spindle will make bearing installation easier and prevent rust from forming. 4. Inspect cups in the hub for pitting, metal flaking, scoring, rust or other obvious damage. Remove any damaged cups with a mild steel bar. Replace cups and cones in matched sets only; not one at a time. 5. Use cup driver or mild steel bar to press or drive the new cup into the hub Wheel / Rim: 12 X 4 JA (4 bolt, 4″ bolt diameter, 2½” rear space) Tire: 4.80 X 12 (B) (4 ply rated; cold pressure rated to 465 lbs. of load at 25 PSI). NOTE: These are standard utility trailer size tires and wheels. Using oversize tires or increasing tire pressures to a level higher than recommended will not increase the Gross Vehicle Weight Rating (GVWR). HUBS For maximum performance from your Sport Wheels and to avoid damage to your trailer, observe the following precautions: •When buying a replacement hub, check that the hub flange is no smaller than a diameter of ?”. •The replacement hub must accept the 1″ bearing (Part Number L44643) and matching cup. •Torque all lug nuts holding the wheel to 75 ft. lbs. TRAILING ARM / SWING ARM No maintenance is required for the trailing arm bearings for the life of the trailer. However, if the trailing arm is removed for any reason the following steps must be followed. 1. Once the ¾” X 16 hex nut has been removed, discard it, and replace with a new lock nut of the same design. 2. When replacing the trailing arm, be sure the bearing spacer is located between the bearings. 3. Torque the hex nut to 14 ft. lbs while moving swing-arm up and down.. DO NOT BACK OFF FOR ADJUSTMENT . Insufficient torque to the

Daytona 675, Street Triple Street Triple R Fitting Instruction

0

Filed Under (Triumph) by admin on 29-10-2010

download
remove the original gear selector rod from the motorcycle. Note: The ball joint and locknut on the transmission linkage have a left hand thread. This is identified by either a machined ring on the gear selector rod on Daytona 675 or on the ball joint on Street Triple and Street Triple R. 1. Front ball joint 2. Locknut 3. Gear selector rod 4. Machined ring, left hand thread identification 5. Machined ring, left hand thread identification (StreetTriple and Street Triple R) 6. Remove the front and rear ball joints and front locknut only from the gear selector rod. Retain the locknut and both ball joints for re-use. Retain the gear selector rod if the motorcycle is to be returned to its original condition. 7. Remove the plastic end caps from the quickshifter assembly. 8. Screw the locknut on to the rear of the quickshifter assembly (right hand thread) leaving 8mm of thread exposed. 1. Quick shifter assembly 2. Locknut 9. Screw the rear ball joint (right hand thread) on to the rear of the quickshifter assembly until it contacts the locknut. Unscrew the ball joint, only enough to achieve the correct orientation in relation to the quickshifter cable, as shown below. Finger tighten the locknut at this stage. 1. Ball joint 2. Quickshifter assembly 3. Locknut 4. Quickshifter cable 10. Fit the locknut and front ball joint (left hand thread) to the front of the quickshifter assembly Screw the locknut and ball joint on to the quickshifter assembly to achieve a dimension between the ball joint ends of 203.5 mm. Ensure that the ball joint is in the correct orientation to the quickshifter cable, as shown below. Finger tighten the locknut at this stage. 1. Ball joint 2. Quickshifter assembly 3. Locknut 4. Quickshifter cable 12. Route the quickshifter cable through the gear selector rod aperture in the frame, as shown. 1. Quickshifter cable 2. Gear selector rod aperture 13. Locate the quickshifter assembly in position, through the frame with the sensor at the rear and the cable at the top. 1. Quick shifter assembly 2. Sensor 14. Attach the front ball joint to the transmission linkage. 1. Ball joint 2. Transmission linkage

HARLEY DAVIDSON VRSC BRACKET FOR BILLET HEADLAMP SHELL REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 31-01-2011

download
REMOVAL VRSCA Models 1. Remove windshield (if equipped). Refer to appropriate Instruction Sheet for procedures. 2. Remove right side cover and maxi-fuse. Refer to MAXI- FUSE in Service Manual. 3. See Figure 1. Disconnect headlamp connector (1) from vehicle wire harness. 4. Remove two screws (2), headlamp mounting bracket (3), and headlamp assembly (4) from upper bracket. 2 3 4 5 1 is03046 1. Connector 2. Screw (2) 3. Bracket 4. Headlamp assembly 5. Screw (2) Figure 1. VRSCA Headlamp Assembly VRSCB Models 1. Remove windshield (if equipped). Refer to appropriate Instruction Sheet for procedures. 2. Remove right side cover and maxi-fuse. Refer to MAXI- FUSE in Service Manual. 3. See Figure 2. Disconnect headlamp connector (1) from vehicle wire harness. 4. Remove two screws (2), headlamp assembly (3), and headlamp mounting bracket (4) from upper bracket. 5. Remove nut (5), screw (6), and trim ring (7) from head- lamp. 6. Remove lens assembly (8) from headlamp shell (9). Save lens assembly for Billet Headlamp Shell Kit 67704-03 installation INSTALLATION 2004-Earlier VRSCA and VRSCB Models 1. Assemble Chrome Billet Headlamp Shell Kit (67704-03). Refer to Instruction Sheet-J03018. NOTES VRSCA models use Headlamp 68297-05, while VRSCB models use original equipment lens assembly (including gasket and boot). Adapter ring from kit (Figure 6, Item 1) will be used to install billet headlamp assembly on Instruction Sheet-J03018. 2. See Figure 3. Cut the two connectors (1) from existing headlamp wire harness (2). Be sure to cut the wires as close to the back of the connector as possible. 3. See Figure 6. Route new wire harness (2) through the hole in bottom of the billet headlamp shell (A). NOTE Only one 16 AWG wire will fit into pin terminals included in kit. Both black wires (ground) can be joined together, then connected to a single wire, if desired. 4. Tape end of one black wire with electrical tape and secure it to wire harness. 5. See Figure 3 and Figure 6. Install terminal pin (3) and socket housing (4) onto new wire harness (Figure 6, Item 2). Refer to MULTILOCK ELECTRICAL CONNECTORS in Service Manual for installing socket/pin terminals. 3 4 1 2 is03025 1. Connector (2) 2. Wire harness 3. Terminal pin (4) 4. Socket housing Figure 3. 2004-Earlier VRSCA and VRSCB Headlamp Wire Harness 2005-Later VRSCA and VRSCB Models 1. Assemble Chrome Billet Headlamp Shell Kit (67704-03). Refer to Instruction Sheet-J03018. NOTES VRSCA models use Headlamp 68297-05, while VRSCB models use original equipment lens assembly (including gasket and boot). Adapter ring from kit (Figure 6, Item 1) will be used to install billet headlamp assembly on Instruction Sheet-J03018. 2. Disconnect and discard existing wire harness. 3. See Figure 6. Connect new wire harness (2) to billet headlamp shell (A). 4. Route wire harness (2) through hole in bottom of billet headlamp shell (A) before installing socket housing (4) provided in kit

Incoming search terms: