how to install conella custom risers on honda fury

You search Auto repair manual PDF how to install conella custom risers on honda fury, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to install conella custom risers on honda fury Direct Download speed 5282 Kb/s

  how to install conella custom risers on honda fury Full Version speed 6162 Kb/s



HARLEY DAVIDSON FRONT THUNDERSTAR WHEELS INSTALLATION

0

Filed Under (Harley Davidson) by admin on 08-11-2010

download
Remove existing front wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to FRONT WHEEL in service manual. For FLSTC and FLSTN Models: Discard moon-style hub cap. -J04065 1 of 8 For FXSTD Models: Discard the tapered r ight side wheel spacer. Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c) NOTE • For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771- 07, 43609-07, 44323-07, 44282-07, 44322-07, 43975-07, 43602-07 and 43773-07 install short valve stem (43157- 83A) included in the installation kit. • For Kits 40943-09, 40966-09 and 40996-09 install long valve stem (43206-01) included in the installation kit. 2. See Figure 2. Install valve stem assembly (L, M or N) on wheel. Refer to TIRES in service manual. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in Service Manual. NOTES Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771-07, 43609-07, 40943-09, 40966-09 and 40996-09: • The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and/or DOT markings to identify it as the brake disc and primary bearing side. • Install the wheel so that the valve stem is on the right side of the motorcycle. For Kits 44323-07, 44322-07 and 44282-07: • Install the wheel so that the hub markings are on the left side of the motorcycle. The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and hub markings to identify it as the primary bearing side. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). • The gross axle weight ratings is unaffected by the installation of this wheel on a vehicle equipped with a 21-inch wheel. For Kits 43975-07, 43773-07, and 43602-07: • The wheel has a machined groove (item 5, Figure 2) in the hub face to identify the right side. • For 2007 and later FX Softail Models and 2008 and later FXDWG: The left side of the wheel is the primary bearing side. For all other models the right side of the wheel is the primary bearing side. • For Kit 43602-07: An arrow is engraved into the right side hub to indicate the direction of rotation. • For Kits 43975-07 and 43773-07: An arrow is cast between the spokes on the right side to indicate the direction of rotation. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake-disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). 4. Install wheel assembly parts from the appropriate Service Parts table for this fitment and stock brake disc. Discard parts from the installation kit that are not required. Refer to FRONT WHEEL in Service Manual. 5. For FLSTC and FLSTN Models: Install wheel kit and right side wheel spacer provided in installation kit. For FXSTD Models: Install wheel kit, stock left wheel spacer and right side wheel spacer from installation kit in place of the tapered right side wheel spacer discarded in Step 1. Refer to FRONT WHEEL in service manual. For FXSTS Models: Install the left side wheel spacer provided in the kit between the stock left wheel spacer and the left fork. All other models: Install wheel spacers previously removed. 6. Install front wheel (1), stock axle and stock axle nut. Refer to FRONT WHEEL in service manual

Incoming search terms:

HONDA GL1100 AM/FM RADIO INSTALLATION MANUAL/ WIRING DIAGRAM

0

Filed Under (Honda) by admin on 22-04-2011

download
INSTALLATION ■ Outline Procedures This section gives general information needed for mounting the individual radio components on and in the fairing. A) Fairing 1) Install radio on fairing before mounting fairing on motorcycle. (Remove fairing from your motorcycle when already mounted). 2) Remove fairing parts. 3) Drill unit mount holes. 4) Install six wire clips. 5) Install windshield on fairing before install- ing speakers. 6) Install radio indicator I on indicator panel II , then install indicator panel on fairing. 7) Install speakers III. 8) Install nutplate IV. 9) Install Power Amplifier in fairing. 10) Install radio funer VI. 11) Install the radio controller VII. 12) Install controller base panel VIII 13) Install radio switch sub-wire. 14) Connect adapter harness and wires inside fairing by working through left turn signal lens hole. B) Motorcycle frame and handlebar 1) Remove travel trunk and seat. Unscrew four shelter bolts (M6, one on each side at front and rear) to route antenna feeder. 2) Install antenna mount and antenna IX. 3) Route antenna feeder along the frame tube. 4) Install radio switch X on left handlebar lever bracket and route the wires. 3 of 11 Page 4 C) Fairing instllation 1) Install fairing on motorcycle. 2) Connect motorcycle wire harness 9-P coupler to fairing wire 9-P coupler. 3) Connect radio switch wire to switch sub- wire.4) Connect antenna feeder. 5) Confirm that radio operates properly. Reinstall parts removed in step 2 or (A) and in step 1 of (B). REWORKING ■ Remove Fairing and Fairing Parts (Fig.10) 1) Install radio on fairing before mounting fairing on motorcycle. (Remove fairing from your motorcycle when already mounted). 2) Remove right and left fairing pockets, right and left turn signal lenses, right and left nutplates, left hole cover and indi- cator base panel from fairing. (Fig.10) Fig. 10 LEI-1 NU I PLATE 4 of 11■ Reworking on Fairing — Speaker mounting holes- 1) Remove 18 mm grommet. 2) Lightly roll template so that it will follow contour of fairing snugly. 3) Position template on fairing with its upper and outer edges aligned with those offairing as indicated by arrows. 4) Attach template to fairing using adhesive tape where shown. 5) Punch mark centers of four holes with a
drift and hammer. 6) Drill 6 mm holes through marked centers. To obtain a more balanced response with richer, deeper bases, drill two 50 mm holes in the fairing so as to link the speaker box with the inside of the fairing. Fig. 11-1
—Power amplifier mounting holes- 7) Drill two 5.5 mm holes through concaves in fairing. Fig. 11-2 RIGHT HAND SHOWN, LEFT SIMILAR ADHESIVE TAPE

Incoming search terms:

Type 11 Honda Motorcycle Audio system installation

0

Filed Under (Honda) by admin on 02-11-2011

download
This section gives general information needed for mounting the individual radio components on and in the fairing.
A) Fairing 1) Install radio on fairing before mounting fairing on motorcycle. (Remove fairing from your motorcycle when already mounted). 2) Remove fairing parts.3) Drill unit mount holes. 4) Install six wire clips. 5) Install windshield on fairing before install- ing speakers. 6) Install radio indicator I on indicator panel II , then install indicator panel on fairing.
7) Install speakers III. 8) Install nutplate IV. 9) Install Power Amplifier in fairing. 10) Install radio funer VI. 11) Install the radio controller VII. 12) Install controller base panel VIII 13) Install radio switch sub-wire. 14) Connect adapter harness and wires inside fairing by working through left turn signal lens hole. B) Motorcycle frame and handlebar 1) Remove travel trunk and seat. Unscrew four shelter bolts (M6, one on each side at front and rear) to route antenna feeder. 2) Install antenna mount and antenna IX. 3) Route antenna feeder along the frame tube. 4) Install radio switch X on left handlebar lever bracket and route the wire

HARLEY DAVIDSON PULLBACK RISER KIT FOR 1.25-INCH HANDLEBARS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-02-2011

download
REMOVAL NOTES Cover the fuel tank with clean shop towels to prevent scratching. If replacing the handlebar, refer to the service manual to remove controls, hand levers, handlebar and risers. If only the risers are being replaced, proceed as follows: 1. Remove the two hex head cap screws and split lock- washers on the underside of the upper fork bracket that hold the currently installed risers in place. Discard the screws, but retain the lockwashers for assembly. Retain all additional components from the riser assembly when the screws are removed. 2. Remove and discard the four screws that fasten the currently installed handlebar upper clamp(s) to the risers. Remove and discard the clamp(s). Remove the handlebar from the risers and carefully set the handlebar on the fuel tank. INSTALLATION NOTES See Figure 3. The upper cup washer (A) must be oriented with the flat side up and the lower cup washer (D) with the flat side down. 1. See Figure 3. Align the components as shown, and install the risers (2) to the upper fork bracket. The ground wire (G) and the lock washer (F) are located on the right side only. Do not tighten the riser mounting screws (4) at this time. 2. If an appropriate Harley-Davidson 1-1/4 inch handlebar has not been installed, install one according to the Instruction Sheet included with the kit, or install the handlebar assembly onto the risers. 3. Loosely install riser caps (1) onto the handlebars and risers with the Bar & Shield toward the front of the motorcycle (Figure 1, Item 1). Install four socket head screws (3) with four washers (6). 1 is05253 1. Bar & Shield (install toward front of motorcycle) Figure 1. Bar & Shield on Riser and Cap 4. Check that the risers stay properly aligned with the handlebar and tighten the riser mounting screws following the instructions in the service manual. 5. Adjust handlebar to the desired position, verify that it is centered on the risers, then tighten the front socket head screws (3) to 12-15 ft-lb (16-20 Nm) . There should be no gap at the front of the risers.

Incoming search terms:

HONDA VTX1300, VTX1800 R, C & S MODEL HANDLEBAR RISERS INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 27-12-2010

download
1 .Lay a blanket folded several times over the fuel tank to protect it. 2. Notice on the 1800 models that there is a small punch mark on the handlebars located on the right hand, front side of the handlebars where the risers meet the top clamp/speedometer housing. This is to reference the handlebar position when re-assembling. On the 1300 models there is a punch mark on the forward facing side of the clamp, these must be installed the same way. 3. Loosen the two 19mm nuts holding the risers to the upper triple clamp (steering head). 4. Pry out the four chrome caps covering the handlebar bolts. Remove the four handlebar clamp bolts. (6mm allen wrench). While sitting on the motorcycle, pull the handlebars and upper clamp off of the risers. They may be slightly stuck and require some force to get free. Lay the handlebar and/or upper clamp/gauge assembly carefully on the blanket. 5. Remove the 19mm nuts and the risers from the triple clamp. NOTE: Be careful not to scratch the upper triple clamp when installing the new risers. Place the thin flat washers provided into the recess at the top of the riser bolt holes on the triple clamp. Assemble the lock washers provided and then the original flat washers onto the bolts provided. Install the new risers onto the triple clamp and snug the bolts. 6. Re-install the handlebars and upper clamp/gauge assembly. ( Remember the punch marks) Tighten the front bolts first closing the gap at the front, and then tighten the rear bolts. Tighten the two 19mm riser-mounting bolts securely. Check for adequate clearance and proper routing of cables and hoses.

HONDA VTX1800R AND HONDA VTX1800N BIG SHOTS EXHAUST SYSTEM REMOVAL

0

Filed Under (Honda) by admin on 17-11-2011

download
If motorcycle is oxygen sensor equipped, unscrew the sensors from the stock exhaust system and install them
into the Vance & Hines exhaust system, being sure to install the front cylinder sensor into the lower pipe and
the rear cylinder sensor into the top pipe. Note: Use caution when handling. Do not touch sensor tip area.
2. If motorcycle is not oxygen sensor equipped, install both M12 x 11 plugs and washers (supplied)into the oxygen
sensor bosses. 3. Check condition of stock exhaust gaskets. Replace if damaged or worn. 4. Install and tighten supplied mounting bracket (stamped 345-P) in the original mounting bar location, using one M10 x 35 flange bolt and nut on top (supplied) and one M10 x 20 flange bolt on bottom (supplied) (Figure 2). Note: The bracket mounts behind the top frame mount and in front of the bottom frame mount(Figure 2).5. Install and tighten rectifier using M6x30 flange bolt, nut
and washer combinations (supplied) (Figure 2). 6. Place heat shields on a non-abrasive surface such as a blanket or carpet. Using a felt tip marker mark outside surface of front and rear heat shields with location of the mounting clips welded to the inside

Incoming search terms:

HONDA 420 RANCHER 2×4/4×4 2007-2009 CLUTCH KIT INSTRUCTIONS

0

Filed Under (Honda) by admin on 22-12-2011

download
Remove key from the ignition switch. Remove the side panels from both sides. Remove both foot wells. 2. Drain coolant. Remove the oil drain plug from the motor; if you carefully drain it into a clean container you should be able to reuse it. 3. Disconnect shift motor (on electric shift models only). Remove coolant hoses. 4. Remove the bolts that mount the front differential to the frame, no other parts need to be removed. Carefully slide the front differential towards the front of the machine; you might need to lift up slightly to get the differential to move. Remove the drive shaft. Remove o-ring on output shaft (on motor). 5. Remove the fuel pump. 6. Loosen the front crankcase cover bolts, keep track of each bolt length and location. Slowly remove the crankcase cover. Carefully watch for o-ring shims and dowel pins that may fall out. 7. Unstake the nut holding the clutch on and remove nut. Using Honda tool #07933-HB3000A thread the large part of the tool into the center of the clutch. Tighten the center bolt on the tool while holding the large part of the tool with a wrench. This will pull the clutch off the machine. Place the clutch on a clean work surface. EPI performance.com
8. Using the c-clamps push down slightly on the outside cover and remove the four e-clips. Keeping track of which way they come off, remove the round metal plates one at a time. This will allow you to see the complete spring. Remove one end of each spring using a spring tool or needle nose pliers and then remove springs. Install the EPI springs by inserting the spring into the outer edge first. Using a spring tool or pliers (45 degree bent pliers work well) pull on the spring and insert the end into the hole. Install the metal plates and the e-clips. If you can’t get the plates to sit flat make sure each clutch arm is flat against the bottom plate of the clutch. Occasionally when you put the springs on, the clutch arms will pop up. Slide the clutch into the machine. The Sprague clutch is marked “outside” when installing make sure this is facing out. Torque clutch nut to 87 ft/lbs. 9. Clean the gasket surface on the motor and on the cover. Put a thin layer of Honda Bond or Yamabond semi-drying liquid gasket (or something similar as long as it is semi-drying) on the crankcase cover. Carefully install crankcase cover, do not force cover on. Torque bolts to 9 ft/lbs. 10. Install the fuel pump. 11. Install the o-ring on the output shaft (on motor) and install the drive shaft. Carefully slide the front differential back into place and mount to the frame. Install the coolant hoses. Refill your engine coolant to the proper level according to your owner’s manual. 12. Install the oil drain plug. Refill your engine to the proper level according to your owner’s manual. You can reuse your oil if it is clean and was drained into a clean container. Only use manufactures recommended oil. 13. Be sure to double check coolant and oil levels and to look for any leaks after the machine has run for a few minutes. 14. Go out and ride your machine. If your performance doesn’t seem right double check to make sure everything has been done properly. 15. EPI is constantly testing our products. Sometimes there is a need to contact the user with new technical information. To ensure that you are receiving this information visit our web site EPIperformance.com to register your clutch kit.

1981-1983 Yamaha Virago 750 & 920 Installation Instructions

0

Filed Under (Yamaha) by admin on 11-02-2012

download
Start by loosening the rear cylinder down tube bolt located on the top of the old mufflers center collector in front of the rear tire. 2. Remove both of the front cylinder exhaust pipe head nuts and set them to the side for reuse with the MAC exhaust system. 3. Remove the right side passenger’s foot peg. Set the foot peg aside as you will need to reinstall it. 4. Remove the left side passenger’s foot peg. Set this foot peg aside as it will also need to be reinstalled. Note: When you remove this bolt the entire exhaust system will be loose and may fall. You will need to support the old exhaust at this point to keep from injuring yourself. Gently move the old exhaust system side to side to remove it from the rear cylinder down tube. Once the exhaust system is loose from the down tube remove the system from under the Virago. 5. Remove the bolt holding the rear brake pedal in place and remove the brake pedal from the motorcycle. Note: Set both the bolt and the pedal aside for reinstallation. 6. Next loosen the nut on the drivers right foot peg, 1 full turn to start with. Then remove the rear nut on the same foot peg. (Note: The bolt that this nut is on goes completely through the motorcycle. This is the center stand mounting bolt.) Now remove the front nut and set both aside for reuse with the MAC system. 7. Install the center stand stop bracket under the left passenger foot peg. Install this bracket with the 90° bend facing down and towards the rear tire. (Note: Center stand sop bracket in provided in the hardware kit and is approx. 5″ long with a 90° bend in it.) Adjust the bracket by one of the large bolts through the foot peg then through the bracket and then install it into the stock location. Put on one of the washers and a nut and snug up the nut. Lower the center stand until the center stand come in to contact with the bottom of the bracket. Tighten the nut until it will hold the bracket securely. 8. Install the rear down tube clamp onto the rear muffler and install the medium sized nut/bolt/washer onto the clamp just finger tight. 9. Install the (2) small bolts into the channel bracket on the rear muffler. Install the rear mounting bracket onto the two bolts and then install the washers and nuts onto each. Tighten the (2) nuts only slight amount so that you can slide the bracket front to rear to insure that when you install the bracket you position it properly. 10. Slide the rear pipe onto the rear down tube about ¼”to ¾” past the pre-cut slots on the rear muffler pipe. Slightly snug the clamp making sure that the position of the bolt and nut will not interfere with any moving parts. The final position of this bolt can hit the tire if it is not positioned properly. 11. Install the other large bolt into the right passenger and then through the top hole in the rear muffler mounting bracket. Insert the bolt into the stock location and install the washer and the nut. 12. Align the rear muffler and you can then tighten the nuts on the rear muffler mounting bracket, the cylinder down tube and the right side passenger foot peg.
13. Install the front muffler on the rear most mounting bolt of the drivers foot peg and put the stock nut back onto the bolt. Hand tighten the bolt only at this time. Note: Install the nut at this time is only to support the muffler and to insure that the pipe does not fall on the ground while you complete the next step. 14. Lift the front head pipe into position and start the stock nuts onto the studs. It is strongly recommended that you install new exhaust gasket at this time. Note: The new exhaust gaskets are not included in the kit but are available at your local Yamaha Dealer. After gaskets are installed hand tighten the front head pipe. 15. Remove the nut from the drivers foot peg bolt and reinstall the drivers foot peg. Note: Hand tighten only at this time. 16. Finish tightening the nuts on the front head pipes. (Install these nuts according to Yamaha’s Factory specifications.) Once the nuts are tightened on the head pipe you can then tighten the drivers foot peg nuts. 17. Reinstall the rear brake pedal and tighten the bolt that holds it on to factory specifications. 18. Check all of the bolts that you have installed of removed to insure that they are tight. 19. Start the motorcycle and check for any leaks. 20. You are finished with your new MAC Exhaust System.

Incoming search terms:

TRIUMPH AMERICA AND SPEEDMASTER HANDLEBAR RISERS INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 29-01-2011

download
1. Place a blanket folded several times over the fuel tank to help prevent any damage during the installation of the risers. Loosen the two 14mm riser mounting nuts located on the bottom side of the upper steering head. Loosen the four handlebar top clamp 6mm socket head screws. 2. It will help having a second person to hold the handlebars while you change the risers. Remove the four screws from the clamps and then remove the clamps. Pull the handlebars up off the risers, pull them back and rest them on top of the blanket. 3. Remove the nuts from the bottom of the risers and remove the risers carefully without allowing the risers to rotate, as this will scratch the clear coating on the upper steering head. Using the bolts, lock washers and washers supplied install the new risers making the bolts finger tight only. (NOTE; again, take care not to allow the risers to rotate as this will scratch the clear coating on the upper steering head). 4. Place the handlebars back up onto the new risers. Install the new top clamps supplied using the four M8 X 30mm socket head screws supplied. Set the height of the handlebars to the desired position, tighten the front bolts first and then the rear securely. (15-18 ft. lbs.) (There should be no gap between the riser and clamp at the front side) Tighten the two riser mounting bolts securely. (20-25 ft. lbs.). 5. Turn the handlebars all the way to the left and then right checking for any pulling or binding of the wires, hoses or cables. YOU MUST! Check to see that the throttle returns freely on its own when the handlebars are at full left and full right turn THIS STEP IS VERY IMPORTANT FOR OBVIOUS SAFETY REASONS! If you have a windshield installed it may be necessary to reroute the throttle cables, wires or hoses around the other side of the windshields mounting hardware to obtain adequate free play and free throttle return. You may also wish to remove the plastic clips or cable tie which secure the wiring to the handlebars and secure them to the brake hose and clutch cable (not the throttle cables) for a cleaner appearance

HONDA VTX1300 "C" MODEL HANDLEBAR RISERS INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 21-12-2010

download
1. Lay a blanket folded several times over the fuel tank to protect it. 2. Remove from underneath, the two hex nuts holding the handlebars to the upper triple clamp. (Steering head) Remove handlebars & carefully set on blanket. 3. NOTE: Be careful not to scratch the upper triple clamp when installing the new risers. Assemble the supplied lock washers and flat washers onto the supplied bolts. Install the new risers onto the triple clamp and finger-tighten the bolts. 4. Re-install the handlebars onto the risers & finger tighten the nuts. Align handlebars & risers to be parallel & centered. Tighten the two riser-mounting bolts securely. Tighten the handlebar mounting nuts securely. Check for adequate clearance and proper routing of cables and hoses

Incoming search terms: