how to adjust carburator rouser 180

You search Auto repair manual PDF how to adjust carburator rouser 180, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to adjust carburator rouser 180 Direct Download speed 5282 Kb/s

  how to adjust carburator rouser 180 Full Version speed 6162 Kb/s



Adjusting the Pekar K68 for Dnepr or Ural

0

Filed Under (Tips and Review) by admin on 11-11-2010

download
1. Make sure the ignition timing is correct 2. Adjust the valves as necessary to ensure proper operation 3. Run the engine to warm it up a bit 4. Adjust the float setting. To do this, remove the carburetors (leave the throttle cables attached), remove the bowl and turn the carburetor upside down (fuel will spill). The float should look like this: Adjust as necessary by bending the float support (#37 in Figure 1). Reinstall Installation and idle adjustment 1. First you must adjust the idle. It is acceptable per the manual to adjust the idle by using the idle adjust screws (11). This usually involves screwing them then backing out 1 to 1.5 turns. Or you can adjust looking at the sliders 2. If installing the carburetors: a. Remove the cover (2) b. Reomve the slider (3) c. Place the throttle cable through the guide (18) with the spring (4) on the cable. d. Route the cable through the slide catch (6) e. Insert the slide assembly into the chamber and make sure it easily slides up and down. Direct the needle (8) into the opening of the diffuser (angled side visible). f. Screw assembly together and verify via throttle movement that slide moves freely. Attach fuel delivery lines to (12). 3. Using the idle set screw (11) raise the slider so the lower edge is 1-2 mm. 4. Assemble to engine using the proper gaskets (paper – felt – paper). 5. Using the locknut (26) adjust the free play of the throttle cable (2-3 mm) 6. Adjust the idle mixture screw – turn in completely then out 1 to 1.5 turns. * Starting using the K68′s (cold weather) 1. Verify fuel flow. Apply choke (pull 52 in Fig1). 2. Using the ticklers (13) allow fuel to enter the bowl until fuel drains from (14) 3. With the ignition off, kick 1 or 2 times 4. Turn ignition on, and as soon as engine is warmed up (maybe sooner) push choke mechanisms to open choke Idle Adjustment (engine running and warm) 1. Remove one of the spark plug caps, and with the cap shorted, adjust (11) to decrease RPM’s to a point of being minimally steady. 2. Adjust the mixture (15) out until RPM’s decrease. Turn in until RPM’s increase slightly. Then turn in screws ¼ to 1/3 revoultion. 3. Do the same for the second carburetor with the first spark plug cap shorted. 4. With both cylinders, adjust each idle (11) on each carburetor the same amount each until it’s at a steady, minimal RPM. Use small changes. (at this point you can use your airflow tool to check). 5. Sharply increase, then decrease throttle. Then engine must return to low RPMs smoothly. If the engine goes below limits, readjust (11) from step 4. Synchronization of the K68 Note: Rather than using the opposite cylinder shorted to test the pull of the live cylinder carburetor, you can use something like a Twinmax connected to the test ports (27 Fig 1). Or, if you have a model without these ports, use a Synchrometer (Appendix 2) held against the face of the carburetor. These tools merely show airflow passing through each carburetor (which is dependent on the position and wear on the slide). If using these tools, it’s not necessary to do the following steps. You wil want to use a throttle guide (Appendix 1), to show airflow at various throttle settings. Using the flow meter of your choice make sure each carburetor is the same at the various throttle settings. 1. Place the motorcycle on the center stand ensuring the rear wheel is suspended 2. Make sure you have large area to work with (safety issues here) 3. Shift into the highest gear with the engine running 4. Short one spark plug cap to the cylinder (using a nail or something in the fins) 5. Increase the speed to 40-50 km/hr 6. Fix the throttle using the throttle (maybe using a throttle stop screw under the throttle housing). 7. Reconnect other cylinder and using the opposite carburetor determine the speed which should be the same as the first. 8. Adjust the position of this slide to achieve the referenced speed using the locknut at the top of the carburetor.

Incoming search terms:

KAWASAKI TERYX EFI Installation Instructions.

0

Filed Under (Kawasaki) by admin on 08-02-2011

download
Basic Tuning Adjustments 1. The following instructions are for basic fuel tuning. Modes 1,2, & 3 are allowing adjustments to increase and decrease the amount of fuel the engine needs. Modes 4 & 5 are for advanced tuning only. DO NOT change modes 4 & 5 when doing basic tuning! 2. To help understand how these modes work, you can think of them as if you were working with a carburetor. 3. Remember each time you push the MODE button you will be advancing to the next mode. Push the MODE button once and you are now in mode 1, push the MODE button again and you are now in mode 2 and so on. You only need to be concerned with modes 1, 2 & 3 for basic tuning. Modes 4 & 5 are for advanced tuning ONLY. 4. If you need to go back to the settings that were pre programmed when you purchased the controller, just look at the picture in each mode, the colored square represents where the settings were when you purchased the controller. 5. Looking at the controller you will see eight lights with numbers under them, this is what you need to look at when changing settings. The #1 light on the controller represents the leanest setting. TRINITY RACING DOES NOT TAKE REPONSIBLITY FOR DAMAGES THAT MAY OCCUR DURING OPERATION OF YOUR VEHICLE UNDER IMPROPER JET SETTINGS. IT IS THE FINAL RESPONSIBLITY OF THE OWNER/RIDER TO ADJUST JETTING TO SPECIFIC RIDING CONDITIONS AND ELEVATION BEFORE RIDING. WARNING! 1.877.FAS TOYS 2.Remove both seats 6. Re-install engine cover and seats. 6. Mode 1 green light represents idle & cruise adjustment (i.e. pilot jet). To adjust this setting push the MODE button once and then push the plus or minus buttons to adjust fuel as needed. 7. Mode 2 yellow light represents an additional amount of fuel added during acceleration (i.e. needle position). To adjust this setting, push MODE twice and then push the plus or minus buttons to adjust fuel as needed. 12 34 56 7 8 12 34 56 7 8 8. Mode 3 red light represents more fuel being added during full throttle (i.e. main jet). To adjust this setting push the MODE button three times and then push the plus or minus buttons to adjust fuel as needed. 9. If you are confident about your tuning skills and feel you need to adjust other parameters, see Advanced Tuning. 12 34 56 7 8 Advanced Tuning Adjustments 1. Advance tuning has two modes in which to adjust. They are called mode 4 and mode 5. In basic tuning, you are changing the amount of fuel that the engine receives, but with advance tuning, you will be changing when the fuel will be available. In each mode you can adjust how soon the fuel delivery occurs. 2. Mode 4 yellow light and blue light represent when the fuel delivery is available during partial throttle acceleration. To adjust this setting, push the MODE button four times and then push the plus or minus buttons to adjust fuel as needed. Only the yellow light will be changing.

Incoming search terms:

Ural carburetors Installation and idle adjustment

0

Filed Under (Ural) by admin on 02-11-2010

download
1. First you must adjust the idle. It is acceptable per the manual to adjust the idle by using the idle adjust screws (11). This usually involves screwing them then backing out 1 to 1.5 turns. Or you can adjust looking at the sliders 2. If installing the carburetors: a. Remove the cover (2) b. Reomve the slider (3) c. Place the throttle cable through the guide (18) with the spring (4) on the cable. d. Route the cable through the slide catch (6) e. Insert the slide assembly into the chamber and make sure it easily slides up and down. Direct the needle (8) into the opening of the diffuser (angled side visible). f. Screw assembly together and verify via throttle movement that slide moves freely. Attach fuel delivery lines to (12). 3. Using the idle set screw (11) raise the slider so the lower edge is 1-2 mm. 4. Assemble to engine using the proper gaskets (paper – felt – paper). 5. Using the locknut (26) adjust the free play of the throttle cable (2-3 mm) 6. Adjust the idle mixture screw – turn in completely then out 1 to 1.5 turns 1. Remove one of the spark plug caps, and with the cap shorted, adjust (11) to decrease RPM’s to a point of being minimally steady. 2. Adjust the mixture (15) out until RPM’s decrease. Turn in until RPM’s increase slightly. Then turn in screws ¼ to 1/3 revoultion. 3. Do the same for the second carburetor with the first spark plug cap shorted. 4. With both cylinders, adjust each idle (11) on each carburetor the same amount each until it’s at a steady, minimal RPM. Use small changes. (at this point you can use your airflow tool to check). 5. Sharply increase, then decrease throttle. Then engine must return to low RPMs smoothly. If the engine goes below limits, readjust (11) from step 4. Synchronization of the K68 Note: Rather than using the opposite cylinder shorted to test the pull of the live cylinder carburetor, you can use something like a Twinmax connected to the test ports (27 Fig 1). Or, if you have a model without these ports, use a Synchrometer (Appendix 2) held against the face of the carburetor. These tools merely show airflow passing through each carburetor (which is dependent on the position and wear on the slide). If using these tools, it’s not necessary to do the following steps. You wil want to use a throttle guide (Appendix 1), to show airflow at various throttle settings. Using the flow meter of your choice make sure each carburetor is the same at the various throttle settings. 1. Place the motorcycle on the center stand ensuring the rear wheel is suspended 2. Make sure you have large area to work with (safety issues here) 3. Shift into the highest gear with the engine running 4. Short one spark plug cap to the cylinder (using a nail or something in the fins) 5. Increase the speed to 40-50 km/hr 6. Fix the throttle using the throttle (maybe using a throttle stop screw under the throttle housing). 7. Reconnect other cylinder and using the opposite carburetor determine the speed which should be the same as the first. 8. Adjust the position of this slide to achieve the referenced speed using the locknut at the top of the carburetor.

Incoming search terms:

Kawasaki FI Calibration Tool Instruction Manual

0

Filed Under (Kawasaki) by admin on 08-02-2011

download
System Function Kawasaki FI Calibration Tool (FI Tool) is developed to modify the mapping of the racing machine to gain operating conditions suitable for the course and the rider’s skill. The following are the available setting functions. Table 1 FI Tool Function Model Name Functions Available Setting Range ’04 ZX-10R ’05 ZX-6RR ’05 ZX-10R ’06 ZX-10R ’07 ZX-6R 1) Adjust the injected fuel rate at acceleration -30 % ~ +30 % 〇 〇 〇 〇 〇 2) Adjust the injected fuel rate of No.1 and No.4 cylinder -30 % ~ +30 % 〇 〇 〇 〇 〇 3) Adjust the injected fuel rate of No.2 and No.3 cylinder -30 % ~ +30 % 〇 〇 〇 〇 〇 4) Adjust the injected fuel rate of primary and secondary injector * -30 % ~ +30 % -10 % ~ +10 % — – — 〇 — – — – — 〇 5) Adjust the ignition timing -15°CA~ +5°CA 〇 〇 〇 〇 〇 6) Adjust the sub-throttle opening angle -50 % ~ +50 % -45 % ~ +45 % 〇 — – 〇 〇 — 〇 — – 〇 7) Adjust the exhaust device opening angle -50 % ~ +50 % 〇 — 〇 〇 — 8) Adjust the all injected fuel rates of all cylinders and operating are a simultaneously -30 % ~ +30 % 〇 〇 〇 〇 〇 9) Adjust the value of engine over revolution limiter 0 ~ +300 rpm -1000 ~ +700rpm -1000 ~+1200rpm — – — 〇 — – — 〇 — – — 〇 〇 — – 10) Set the fuel cut or not at deceleration Use or Not Use 〇 〇 〇 〇 〇 11) Set the sub throttle controlled or not Controlled or Full Open Fixed 〇 — – — – 12) Set the exhaust device controlled or not Controlled or Full Open Fixed 〇 〇 〇 〇 〇 13) Set the Auto Shifter Ignition Cut Length Controlled or not, set Ig. Cut Time by gear range — – 〇 〇 〇 14) Set the Pit Road RPM Limit Controlled or not, set Upper Limit RPM by gear range

APRILIA QUASAR 50-100-125-180 maintenance Manual

0

Filed Under (Aprilia) by admin on 26-11-2010

download
CHANGING ENGINE OIL CAUTION In case of oil leakage or malfunctions, contact an Aprilia Authorised Dealer . Do not dispose of oil in the environ- ment. Dispose of engine oil – stored in a sealed container – through the nearest waste oil reclamation firm or through the supplier. Carefully read page 34 (MAINTE- NANCE) To change engien oil: ◆ Ride for a few kilometres until engine reaches the operating temperature, then stop the engine. ◆ Position a graduated container (1), under the drain plug (2). ◆ Loosen oil filler plug (4) and drain plug (2). ◆ Let oil flow out of the sump. ◆ Loosen oil filter (3) and carefully clean it. ◆ Refit the filter and tighten fully. ◆ Tighten drain plug (2) and pour recommended oil into filler plug (4), see page 58 (LUBRICANT CHART). ◆ Tighten the filler plug. CAUTION Carefully tighten filler and drain plugs and ensure oil does not leak out. Periodically check for leaks at the casing cover gasket. Do not use the vehicle with insufficient lubrication or with contaminated or unsuitable lubricants, since this would cause early wear of the moving parts and may also cause irreparable failures Fluid reservoir (1) is under rear right wheelhouse. CAUTION Position the vehicle on firm and flat ground. ◆ Make sure that the fluid contained in the reservoir exceeds the ” MIN ” mark stamped on the reservoir. MIN = minimum level. WARNING Do not use the vehicle if the braking system is leaking fluid. CAUTION Do not use the vehicle if the fluid is below the “MIN” mark. 1
27 use and maintenance Quasar 50 – 100 – 125 – 180 CAUTION Brake fluid level decreases as the brake pads wear down. Should the level be too low: ◆ Check the brake discs and pads for wear, see page 27 (CHECKING THE BRAKE PADS FOR WEAR) If the pads and/or the disc do not need re- placing: ◆ Contact an Aprilia Authorised Dealer that will top up the fluid. WARNING Check the brake for proper operation. When the brake lever has exceeding travel or if you notice a loss of braking, contact an Aprilia Authorised Dealer . The braking system may need bleed- ing. CHECKING THE BRAKE PADS FOR WEAR Carefully read page 26 (BRAKE FLUID – recommendations) , page 26 (DISC BRAKES) and page 34 (MAINTE- NANCE). Periodically check brake pad wear. The rate at which brake pads will wear depends on vehicle usage, riding style and road surface condition. Outlined below is a quick brake pad inspection procedure: ◆ Visually check between brake disc and pads, check both pads (1) looking from the bottom at the rear end. ◆ Should friction material (of even one pad only) be worn down to 1.5 mm of thickness, have both pads replaced

POLINI X1 GENERAL INFORMATION AND SPECIFICATIONS

0

Filed Under (Polini) by admin on 02-12-2010

download
Air cleaner – Clean and reoil daily or after each moto to prevent motor failure and reduced performance. Transmission oil – change after every race, or at end of riding day. Chain – check tension and lubricate before every ride, adjust or replace as needed. Reoil after riding in damp conditions. Clutch – disassemble and clean clutch assembly frequently, every 2-3 races at least. Inspect kickstarter gears at this time. Ignition cover – remove cover and wipe dry after each ride or after washing bike to remove condensation. Piston rings – replace as often as every 3-5 races with expert rider, less often with less aggressive riders. Piston, pin, rod bearing & circlips – replace as often as every 8-10 races with expert rider, less often with less aggressive riders. Coolant – change yearly, make sure there is at least a 50/50 mixture of antifreeze if freezing temperatures are possible. Steering bearings – Check daily for looseness or play. Adjust and regrease as needed. Swingarm – Check often for looseness. Regrease several times a year. Replace bushings if any play is evident. Sprockets – check for worn or curved teeth each time chain is adjusted. Chain roller& wear pads – check roller for free rotation when checking chain. Make sure roller is not bent or damaged. Check chain wear strips on swingarm and chain guide frequently. Replace as needed to prevent chain from damaging motorcycle. Spokes – Check after each race or after each day of riding for looseness or damage. Wheels & tires – check wheels after each race for dents, cracks or other damage. Check tires for cuts, damage or wear. Check tire pressure daily and adjust for riding conditions. Shock – Check shaft area daily for signs of oil leakage or damage. Check swingarm and shock bushings for looseness. Forks – Check forks daily for leaking oil or damage to tubes. Make sure forks are not twisted check for smooth operation. Spark plug – check sparkplug color and condition after each race or end of riding day. Adjust jetting to keep plug from fouling or overheating. Silencer – If bike seems to be getting louder, replace packing and decarbonize inner tube. Expansion pipe – check daily for large dents, damage or leakage. Remove carbon from headpipe when pipe is removed. Have large dents fixed, or any dents within 8″ of the cylinder. Replace o-rings on pipe as needed to maintain a good seal. Footpegs – check daily for proper operation, pegs should spring back into place. Make sure pegs are not bent or overly dull. Handlebars – check bars after any crash for bending. Look for cracks near bar clamps. Replace bars that have been straightened more than 2 or three times, or if bar is badly bent. Aweakened bar can snap suddenly causing injury to rider. Throttle – check throttle for proper operation each time before bike is started. Remove and clean inside of grip and bar as needed. Grips – check grips daily for wear or looseness. Replace as needed. Use grip glue & safety wire to help hold grips in position. Calipers & pads – check pad wear and caliper function daily or after each race. Replace pads and clean calipers as needed. Brake lever – check lever daily for damage or wear. Make sure lever is at proper angle for both seated and standing positions. Leave lever clamp loose enough to allow clamp to rotate during crash rather than breaking lever. Check and adjust freeplay as needed. Brake pedal – Check pedal daily for damage and proper freeplay. Adjust rear caliper as needed. Reeds – Remove and inspect reed block during every ring change. Check reeds for signs of wear, fraying and cracking. Make sure reeds sit flat and seal well. Replace at any sign of wear or damage or at least once a year, more often for expert riders. Nuts & bolts – Check all nuts and bolts regularly. Make sure to check engine mounting bolts and swingarm bolt frequently

HARLEY DAVIDSON 180 MM WIDE TIRE KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
INSTALLATION Install Wide Tire 1. Place motorcycle on a lift and secure front tire. 2. Place a scissor jack under the frame so that the rear wheel can be raised and lowered. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 3. Disconnect battery negative (-) cable. 4. Refer to the appropriate Service Manual and remove the rear wheel. 1 3 4 2 is00773 1. Tail/Stop Connector 2. Left turn signal connector 3. Right turn signal connector 4. Power in connector Figure 1. Remove Connectors 7 8 9 1 6 2 4 5 3 is00705 1. Rear fender 2. Stock rear fender bracket 3. Stock washer 4. Stock hex screw 5. Stock washer 6. Rear fender bracket from kit 7. Stock fender strut cover 8. Stock screw 9. Stock turnsignal and mount assembly Figure 2. Replace rear fender bracket

How To Adjust the Accelerator Pump On the 40mm Mikuni Carburetor

0

Filed Under (Yamaha) by admin on 21-01-2012

download
1) The “blue” colored screw in the image is the duration adjustment screw. Underneath the head of the screw is a lock nut and the bracket arm that the screw is threaded into. To decrease the amount of fuel squirted the adjustment screw is turned “clockwise” or in. To increase the amount of fuel squirted the adjustment screw is turned “counter clockwise” or out. To get the max, amount of decrease remove the screw and take the lock nut off of the screw. Then replace the screw into the cam arm, then replace the lock nut underneath the arm on the screw. this gives you another 3/32″ of an inch in which the screw can be screwed in.
2) Turn the adjustment screw fully clockwise or IN. Start your engine, Blip your throttle open, if the engine stutters, (hesitates), it is not getting enough fuel so turn the screw counter clockwise to increase the amount of fuel squirted from the accelerator pump into the carburetor. Keep blipping the throttle and adjusting the screw till the carburetor starts to cough. Stop here and turn the screw back in till the coughing stops. Tighten down the lock nut. This should give you the best throttle response with the least amount of coughing and backfiring out the carburetor. Timing Adjustment Screw This is the “Green” colored screw just above the Blue duration adjustment screw. The” Mucker” said it best,,,,, This upper screw adjusts the “timing” of the squirt. By altering it’s setting, you can advance or delay the onset of the fuel squirt. But probably, it won’t have to be touched

Incoming search terms:

Lilac LS-18 Motorcycle Maintenance Standards

0

Filed Under (Lilac) by admin on 25-11-2010

download
CYLINDER AND CYLINDER HEAD MAINTENANCE ITEM STANDARD REPAIR LIMIT METHOD REMARKS Cylinder Bore 54 -0.01 54.1 Boring After boring honing should be performed Ovality 0.01 0.05 Boring After boring honing should be performed Taper 0.01 0.05 Boring After boring honing should be performed Oversize 0.25 steps 55 max. Do R and L cylinders at same time / 4 steps Valve Seat Width 0.8 – 1.0 1.3 Adjust Use a cutter Angle 45∞ Combustion Chamber Volume 18.2cc -0.5cc Remove carbon if heavy accumulation Compression Ratio 7.8:1 Head Gasket Thickness 1.0 Cylinder Head Nut Torque 3.0 kg/m (22 ft.-lb.) Out standard Adjust 8mm nut Intake and Exhaust Ports Port Wall SurfaceMust be smooth Remove carbon Intake and Exh. Valve GuidesOD 12 +0.09 +0.1 ID 7 +0.01 -0.0 7.06 Exchange Intake Valve Stem Diameter 7 -0.02 -0.03 6.9 Exchange Head Thickness 1 0.7 Exchange Exhaust Valve Stem Diameter 7 -0.02 -0.03 6.9 Exchange Head Thickness 1 0.7 Exchange Intake and Exhaust Valve Seat Face Width Range 0.8~1.0 1.3 Use valve seat cutter Intake Valve Guide Clearance 0.02~0.04 0.08 Replace valve or guide Exhaust Valve Guide Clearance 0.06~0.08 0.12 Replace valve or guide Valve Spring (Large) Installed Load 10.2 kg 8.7 kg Replace Fitted length 31.5 Free Length 36.5 34.7 Replace Tilt 1.5/100 3/100 Replace Valve Spring (Small) Installed Load 5.48 kg 4.65 kg Replace Fitted length 29.5 Page 4 of 10 Free Length 33.5 31.8 Replace Tilt 1.5/100 3/100 Replace Rocker Arm ID 12 +0.00 +0.02112.07 Replace Rocker Shaft OD 12 -0.06 -0.024 11.92 Replace Arm and Shaft Clearance 0.045~0.006 0.10 Replace arm or shaft Tappet Clearance 0.05 Out standard Adjust Measure cold at TDC Rocker Arm Ball Surface 1.8îR -0.006 -0.024 Replace if severe wear Pushrod Bend 0.1 0.5 Straighten Over 100mm (2) CRANKSHAFT, PISTON AND CONROD MAINTENANCE ITEM STANDARD REPAIR LIMIT METHOD REMARKS Piston OD @ Top 53.65 -0.02 Max Diameter 53.95 -0.015 53.85 Replace Ovality 0.1 Piston and Cylinder Clearance 0.04~0.05 0.15 Replace Piston Ring Groove Clearance 0.03~0.07 0.10 Replace Piston Oversize Step 0.25 4 steps Top Ring and 2nd Ring Thickness 2 -0.01 -0.03 1.92 Replace Width 2.5 -0.01 0.55kg Tension 0.85 – 1.15kg 1 Replace End Gap 0.15 – 0.35 Replace Oil Ring Thickness 3.2 -0.01 -0.03 3.12 Replace Width 2.5 -0.1 Tension 1.0~1.3kg 0.65kg Replace End Gap 0.15~0.35 1 Replace Ring Gap Position 120∞ 3 equal spacesOut standard Adjust Avoid Piston Pin Axis Ring Oversizes 0.25 steps 4 steps Piston Pin OD 15 -0.0 +0.006 14.95 Replace Pin Hole in Piston ID 15 +0.012 -0.015.05 Replace Pin and Piston Clearance -0.006 ~ +0.012 0.06 Replace Hand push fit piston at 100∞C Conrod Small End Bush ID 15+0.027+0.016 15.07 Replace bush Conrod and Piston Pin Clearance 0.01~0.027 0.07 Replace Crankpin OD 24.94 +0.0+0.0124.90 Replace Crankpin Roller OD 5 (+0.001+0.003) Refer to conrod ID Replace 3Sizes; 52 per assembly for selective fit 5 (+0.0 -0.002) 5 (-0.003 -0.005) Conrod ID 34.95+0.03+0.02435.02 Axial Play 0.2~0.4 0.5 Adjust Radial Play 0.026~0.036 0.06 Replace

Incoming search terms:

Motorcycle Navigator ZUMO Z500/550 Owner's Manual

0

Filed Under (Tips and Review) by admin on 16-11-2010

download
GETTING STARTED Looking at Your zūmo A. Power button B. Zoom in, raise volume, or increase brightness. C. Zoom out, lower volume, or decrease brightness. D. Page button—scroll through the Map, Trip Information, Media Player, and Phone Menu pages. Press and hold to adjust brightness. E. Speak button—press to adjust volume level. Press and hold to announce voice directions. SD card slot Mini-USB port for AC adapter, USB Mass Storage mode, and updating software A B C D E MCX connector under weather cap (see page 55 ) Battery pack (see page 54 )
2 zūmo 500/550 Owner’s Manual GETTING STARTED zūmo Tips and Shortcuts • Touch and hold to quickly return to the Menu page. • Press to return to the Map page. • Touch and to see more choices. • Touch to adjust settings such as volume, brightness, language, and keyboard. Adjusting the Volume Press , and then use and to adjust the volume. For advanced volume settings, touch > Volume . Adjusting the Brightness Press and hold , and then use and to adjust the brightness. See page 44 for additional display settings. Quick Links • Finding an address: page 11 • Viewing the Map page: page 20 • Using hands-free mobile phone features: page 23 • Using the Garmin Lock™ anti- theft feature: page 10 • Listening to MP3 files: page 37 • Transferring files to your zūmo: pages 34-36 • zūmo audio options, see page 46 • Cleaning and storing your zūmo: page 55 • Mounting the zūmo in your automobile: page 47 Fill out the Product Documentation Survey. Go to www.garmin.com/ contactUs , and click Product Documentation Survey .

Incoming search terms: