harley sportster front axle nut torque setting

You search Auto repair manual PDF harley sportster front axle nut torque setting, if there are search results will appear below. If search results do not exist, please search by others keyword.



  harley sportster front axle nut torque setting Direct Download speed 5282 Kb/s

  harley sportster front axle nut torque setting Full Version speed 6162 Kb/s



HARLEY DAVIDSON REAR AXLE-NUT COVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 31-01-2011

download
REAR AXLE-NUT COVER KIT GENERAL Kit Number 41704-09, 41705-09, 41706-09 Models For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories section (English only). Additional Parts Required The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents See Figure 1 and Table 1. INSTALLATION NOTES The shorter axle-nut cover mounts to the right side of the motorcycle. Axles that have been removed for service, replacement or repair may have been assembled in reverse orientation from their stock design. Axle-nut covers may not fit properly on reversed axles. Refer to the appropriate Service Manual for correct axle orientation. 1. Adjust the position of the exhaust system (if necessary) to provide axle-nut clearance. 2. Position each axle-nut cover over the appropriate axle nut. 3. The skull version nut covers have two set screws per cover. Position the logo and snug up one set screw to hold in place and the other to prevent rotation. 4. Tighten the axle-nut cover set screws to 70 in-lb (7.9 Nm) . NOTE The set screws in this kit are treated with a thread-locking compound. When replacing or re-installing the set screws (2), apply Loctite® 243 (Blue) Threadlocker and Sealant (Harley- Davidson Part Number 99642-97) to the set screw threads. SERVICE PARTS

Incoming search terms:

HARLEY DAVIDSON DYNA AND SPORTSTER Chrome Front Wheel Spacers INSTALLATION ISNTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Block motorcycle underneath frame so front wheel is raised off the ground. 2. See Figure 1. Remove the upper (1) and lower (2) brake caliper mounting bolts and brake caliper(s) (3). Support caliper(s) using a rubber bungee cord. Be careful not to scratch fender paint. NOTES Do not operate front brake lever with the front wheel removed or the caliper piston may be forced out of piston bores. Reseating the piston requires disassembly of the caliper. Prior to removal, make note of existing left and right spacer location. The new spacers will be installed in the locations. 3. See Figure 3. On left side of wheel, remove axle nut (D), lockwasher (E) and washer (F). Perform the following: 4. Sportster and Dyna (except FXDWG) See Figure 2. Loosen the pinch bolt nut (1) and pull the the axle (2) free. Remove wheel and spacers. Leave bearing(s) in place. Discard spacers. 3 1 2 is04469 1. Brake caliper mounting bolt, long (top) 2. Brake caliper mounting bolt, short (bottom) 3. Brake caliper Figure 1. Caliper Mounting Bolts (Left Side) Dyna and Sportster 3 1 2 is04470 1. Pinch bolt nut 2. Axle 3. Pinch bolt Figure 2. Front Wheel Mounting (Dyna and Sportster Except FXDWG-Right Side) 5. See Figure 3. Obtain the new right (1) and left (2) chrome spacers from kit and install. 6. Apply a light coat of ANTI-SEIZE LUBRICANT (Harley- Davidson Part Number 98960-97) to the axle.
7. Place wheel between sliders and install axle. Verify that axle spacers on right and left side are properly installed. 8. See Figure 3. Install the washer (F), lockwasher (E) and nut (D) onto threaded end of axle (A). 9. In order to properly align the front fork, perform the fol- lowing: a. On the right side of the wheel, insert a 7/16 inch drill bit through the hole in the axle. While holding axle stationary, tighten axle nut to 50-55 ft-lbs (61.0-74.6 Nm) . b. Pull fork leg so that it just contacts drill bit. Tighten according to the following: c. Refer to Figure 2. Tighten the Axle Pinch Bolt Nut to 25-30 ft-lbs (33.9-40.7 Nm) . d. Remove drill bit from axle hole. 10. Follow instructions in Service Manual and install brake caliper to the sliders noting the following: •Loosely install long bolt to the top hole on fork leg. Install the short mounting bolt to the bottom hole and tighten to 28-38 ft-lb (38.0-51.5 Nm) . •Final tighten top bolt to 28-38 ft-lbs (38.0-51.5 Nm) . 11. Repeat Step 10 to install brake caliper on opposite side of wheel. After servicing brakes and before moving motorcycle, pump brakes to build brake system pressure. Insufficient pressure can adversely affect brake performance, which could result in death or serious injury. (00279a) 12. Pump brake lever to move pistons out until they contact both brake pads. Verify piston location against pads

ACE -325X/ 395 X-XX CLOCK, UNIT, WHEEL, ODOMETER, TEMPERATURE & FUEL METER SETTING

0

Filed Under (Honda) by admin on 24-12-2011

download
Setup operations include 12/24hour clock, bar tachometer scale, shift warning RPM, numbers of engine rotation per signal, wheel circumference, units, odometer adjustment, units of temperature, temperature warning and fuel meter input resistance selection. These must be set up step by step. The computer will automatic reversion to main screen if no button operation for 75 seconds at any setting screen. 2. Press both MODE & RESET buttons to go into setting screen. In setting screens, press RESET button to add the flashing digit by 1 or convert units, press MODE button to confirm the digit setting and jump to next digit or next setting screen to be set. Press MODE button for 2 seconds at any setting screen to finish the setting and go to main screen. 3. It displays “12 or 24H and XX:XX-XX” symbols and AM/PM in case you select 12H. Operates buttons as descriptions of item 2 to finish clock and jump to 8,000/16,000rpm scale setting. 4. It displays 8,000rpm scale, presess RESET button to convert 8,000 or 16,000rpm. Press MODE button to confirm the setting and jump to shift RPM warning setting. 5. It displays ” RPM rXXX00 “. Follow the item 2 of button operation to finish the shift RPM warning setting and jump to engine specification setting. 6. It displays “SPC-X.X RPM”, the default value is 1.0; there are 4 options: 1.0, 2.0, 3.0 and 0.5. It means the numbers of engine rotation per signal. For example the value 2.0 means the engine rotate 2 turns to output a signal. 7. Press RESET button to move in loop sequence from one to another value of the 4 values. Press MODE button to confirm the setting and go to wheel circumference setting screen. 8. In “cXXXX” display, “c” means “Circumference”, following 4 default digits; flashing digit is digit to be set. Follow the item 2 of button operation to finish the wheel circumference setting and jump to unit setting. 9. It displays KM/h or MPH, each press of RESET button converts unit; press MODE button to confirm unit setting and jump to odometer setting. 10. It displays “ODO & 00000Xkm”, the “X” is tested odometer in factory, follow item 2 to setting a desired odometer and jump to thermometer unit setting. The setting screen will disappear when the odometer is over 30km or your setting is over 30km and returned to main screen. 11. It displaysm ” , or oFF”, each press of RESET button converts , or oFF; press MODE button to confirm temperature setting and jump to temperature warning setting. 12. It displays ” XXX” and the selected unit. Follow the item 2 of button operation to finish the temperature warning setting and go to fuel sensor input resistance setting. 13. It displays “100r and fuel tank symbol”, follow the item 2 to select 100, 250, 510 Ohm or oFF and return to the main screen. The fuel meter bar will disappear if you select oFF mode.

Incoming search terms:

HARLEY DAVIDSON SOFTAIL CHROME REAR AXLE ADJUSTER AND COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 16-04-2011

download
INSTALLATION Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) 1. Block the motorcycle underneath the frame so the weight of the vehicle is off of the rear wheel, but do not raise the rear wheel off the ground. 2. Some models require loosening or removal of the muffler or mufflers in order to remove the rear axle. See the EXHAUST SYSTEM REMOVAL section of the Service Manual. Remove the saddlebags if desired for extra working clearance. See SADDLEBAG REMOVAL in the Service Manual. 3. See Figure 1. Remove the original axle adjustment bolts (1) and jam nuts (2) from both sides of the motorcycle and discard. NOTE On a bike that has been previously serviced, ensure that the axle has not been removed and re-installed from the left side (with the castle nut to the right of the wheel). If it has, the axle MUST be inserted from the right side of the motorcycle. 4. Remove the retaining pin (7), castle nut (5) and washer (4) from the left side of the axle (6). Discard the washer, but save the pin and nut for later re-assembly. 5 7 1 4 6 2 3 is04101 1. Axle adjust bolt 2. Jam nut 3. Axle adjuster collar 4. Washer 5. Castle nut 6. Rear axle 7. Retaining pin Figure 1. Rear Axle Hardware (Left Side Shown) 5. Tap the axle toward the right side of the motorcycle and remove. The belt adjuster collars (3) will fall loose as the axle is removed. The collars can be discarded. The wheel bearing spacers may also fall loose or be dislodged. Be sure to return these to their original position on the vehicle (short spacer on the right side, long spacer on the left). 6. Inspect axle components for damage or excessive wear, and replace as required

Incoming search terms:

HARLEY DAVIDSON AXLE CAP NUT KIT (CHROME) INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 05-02-2011

download
INSTALLATION 1. Secure the front wheel of the motorcycle. 2. Remove one hex nut, lockwasher and flat washer attaching the axle holder to the right-side fork damper tube. 3. Assemble a chrome flat washer, split lockwasher and cap nut from the kit to the fork damper stud, but do not fully tighten at this time. 4. Repeat with the remaining nut, lockwasher and flat washer on the other stud. 5. For 2000 and later models: See Figure 1. Insert a 7/16 inch drill bit (3) into the hole in the front axle (2). Pull the right-side fork leg (1) so that it just contacts the drill bit. 1 4 2 3 is04467 1. Fork leg 2. Front axle 3. Drill bit 4. Chrome cap nut, lockwasher and flat washer (2) Figure 1. Align the Front Wheel 6. Tighten the new chrome cap nuts (4) to 9-13 ft-lbs (12-18 Nm)

HARLEY DAVIDSON SOFTAIL REAR AXLE COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-03-2011

download
INSTALLATION 1. 1988-1999 FLSTF Models: Remove rear muffler heat shield, loosen rear exhaust Torca clamp, then remove rear muffler from support following the instructions in the appropriate Service Manual. 2000 and Later Models: Remove exhaust system following the instructions in the appropriate Service Manual. NOTE In some cases, if bike has been previously serviced, the axle may have been removed and re-installed from the left side (with castle nut and cotter pin on the right). If this is the case, the axle must be removed and installed from the the right. If axle appears as original configuration (as in Figure 1), it is not necessary to loosen the rear axle nut or remove the cotter pin (or spring clip) from the rear castle nut. 2. All Models: See Figure 1. On the left side of the motorcycle, loosen the axle adjuster screw (1) and jamnut (2) just enough to be able to remove the jamnut. 3. 1988-1999 FLSTF Models Only: See Figure 2. On the right side (brake caliper side), use a T40 TORX drive to remove the two pin bolts from caliper. Remove caliper by gently rocking caliper back and forth to compress caliper piston, then carefully slide caliper off brake disc. Use cable strap or other suitable means to support caliper. 4. All Models: On the right side, loosen the axle adjuster screw and jamnut just enough to be able to remove the jamnut. 5. All Models: See Figure 3. On each side, place retainer clip (oriented as shown) and washer from kit over axle adjuster screw and replace jamnut. Turn in axle adjuster screw until it is in its original position against axle spacer, but leave jamnut loose. 1 2 4 3 is04788 1. Axle adjuster screw 2. Jamnut 3. Castle nut 4. Cotter pin (or spring clip) Figure 1. Rear Axle Hardware

HARLEY-DAVIDSON Sportster Solid Axle Suspension Owner's Maintenance Notes

0

Filed Under (Harley Davidson) by admin on 16-02-2011

download
1. Tire Pressure and Rotation : Keep the nominal tire pressure at about 24-26psig. It is not necessary to periodically rotate the trike tires unless you experience unusual tire wear. 2. Bearing Lubrication . Your Swing Arm, external differential, and axle bearings are sealed and do not require greasing. However, should you experience unusual differential or axle bearing noise you should take your trike to a Champion Trike Dealer or to your motorcycle mechanic for a checkup. 3. Body Lubrication . There are no grease fittings on the trike body and no required body lubrication points. 4. Differential lubrication . Your differential is a sealed unit and comes filled with high-pressure grease. No maintenance is required. 5. Brakes . Check your brake system fluid level every 3,000 miles and top-off as necessary. Inspect rear disc brake pads every 10,000 miles and replace as necessary. Pads are Volkswagen Part # D101P. 6. Drive Train . Inspect your drive belt as recommended in your motorcycle Owner’s Manual. When properly tensioned after the trike conversion, the belt should “deflect” approximately ¾”-1″ with a new belt or 1″ to 1-1/2″ with a used belt of total vertical movement. Do not use commercial belt dressing compounds on the belt except for Harley Davidson Poly-Oil, PN 99860- 81. These compounds are designed for friction, not toothed, belts and can collect dirt and sand. 7. Suspension System. The suspension is a “Zero Flex” solid axle with high performance adjustable pre-load coilover shocks. The suspension system is designed to give you the best ride with a load of no more than 400 pounds. 8. EZ-Steer (rake kit) : If your trike is equipped with Champion’s EZ-Steer, the bearings are a wear item. You should follow your motorcycle manufacturer’s recommended front-end triple-tree maintenance requirements. Generally these call for an initial service at 1,000 miles followed by periodic maintenance at 10,000 mile intervals

HARLEY DAVIDSON CHROME BELT SPROCKET COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
Installation 1. Remove rear wheel. Refer to the applicable Service Manual for the proper removal procedure. 2. Remove bolts and washers from sprocket. •If you intend to install Acorn Nut and Stud Kit (Part No. 91734-85), refer to that Instruction Sheet at this time (please note that this Acorn Nut and Stud Kit does not fit Sportster (XL) models). •If you do not intend to install Acorn Nut and Stud Kit (Part No. 91734-85), retain bolts and washers for reassembly. Proceed to Step 3. 3. Position sprocket cover so that its mounting holes align with the holes in the sprocket. NOTE There is only one position which allows each hole in the cover to align with a hole in the sprocket. If replacement bolts, washers, or nuts are required, use only genuine Harley-Davidson parts specified for your particular model. Aftermarket fasteners can adversely affect performance, which could result in death or serious injury. NOTE • See Harley-Davidson service manual for proper torque val- ues; •Aftermarket fasteners may not have the specific property requirements to perform properly. 4. Install bolts with washers through holes in sprocket cover and sprocket, and into threaded holes in wheel hub. Depending on the tensile strength grade of the bolts in your particular application, tighten bolts in a crosswise pattern to one of the torque values listed in the following table: 5. Refer to the applicable Service Manual for the proper procedure and perform the following: •Install axle. •Align belt. •Adjust belt tension. •Tighten rear axle nut to 60 – 65 ft-lbs torque. 6. Check sprocket for radial runout (eccentricity). If runout is visible, mark outer edge of sprocket at the location of runout. Loosen sprocket bolts and tap the marked location with a rubber mallet. Tighten sprocket bolts in a crosswise pattern to the applicable torque specified in Step 4.

HARLEY DAVIDSON REAR THUNDERSTAR WHEELS INSTALLATION, MAINTENANCE AND CLEANING

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
INSTALLATION 1. Remove existing rear wheel assembly. Save axle, axle nut, brake disc and wheel spacers for kit installation. Refer to the service manual. NOTES Prior to removing or installing the wheel, the rear brake caliper must be removed. The cotter pin or spring clip for the axle nut must be replaced. They are available for purchase from a Harley-Davidson dealer. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) Do not re-use sprocket mounting screws. Re-using sprocket mounting screws can result in torque loss and damage to the sprocket and/or belt assembly. (00480b) 2. See Figure 1. Install valve stem assembly (E) on wheel. Refer to the service manual. 3. Assemble wheel installation kit components, stock brake disc, and sprocket to wheel using the appropriate service parts table. Refer to the service manual. NOTES Install the primary bearing first, following the instructions in the service manual and using the WHEEL BEARING REMOVER/INSTALLER. The machined grooves in the hub face indicate the primary bearing side. 4. Install rear wheel (1), stock axle, and stock spacers to motorcycle. Refer to the service manual. MAINTENANCE AND CLEANING NOTE This wheel assembly includes plugs that have been installed in the openings between the brake disc mounting holes on one side of the wheel and in the compensator bowl of the 16×5 inch wheel. Missing or damaged plugs can be replaced using Wheel Plug Kit (44459-04) or individual plug (43871-09 – 16×5 inch wheel). Chrome parts must be maintained regularly so they keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley-Davidson Wheel and Tire Cleaner, applied with Harley Wheel and Spoke Brush. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner. 3. After cleaning and polishing, seal the finish with a good quality sealer, such as Harley Glaze Polish and Sealant

HARLEY DAVIDSON REAR ROAD WINDER WHEELS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-03-2011

download
This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson dealer. Kit Contents See Figure 1 and Service Parts Tables. INSTALLATION 1. Remove existing rear wheel assembly. Save axle, axle nut, brake disc and wheel spacers for kit installation. Refer to the service manual. NOTES Prior to removing or installing the wheel, the rear brake caliper must be removed. The cotter pin or spring clip for the axle nut must be replaced. They are available for purchase from you dealer. See your dealer for the correct part number for your model motorcycle. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) Do not re-use sprocket mounting screws. Re-using sprocket mounting screws can result in torque loss and damage to the sprocket and/or belt assembly. (00480b) 2. See Figure 1. Install valve stem assembly (E) on wheel. Refer to the service manual. 3. Assemble wheel installation kit components, stock brake disc, and sprocket to wheel using the appropriate service parts table. Refer to the service manual. NOTES Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. The machined grooves in the hub face indicate the primary bearing side. 4. Install rear wheel (1), stock axle and stock spacers to motorcycle. Refer to the service manual. MAINTENANCE AND CLEANING Chrome parts must be maintained regularly to keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley-Davidson Wheel and Tire Cleaner, applied with Harley Wheel and Spoke Brush. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner. 3. After cleaning and polishing, seal the finish with a good quality sealer, such as Harley Glaze Polish and Sealant

Incoming search terms: