detachable two mating rubber bushings

You search Auto repair manual PDF detachable two mating rubber bushings, if there are search results will appear below. If search results do not exist, please search by others keyword.



  detachable two mating rubber bushings Direct Download speed 5282 Kb/s

  detachable two mating rubber bushings Full Version speed 6162 Kb/s



HARLEY DAVIDSON SOFTAIL DETACHABLE SADDLEBAG KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 22-03-2011

download
Detachable Saddlebag Configurations Table 1 provides a short description of the detachable saddlebag configurations. Table 1. Softail Detachable Saddlebag Configurations Accessory Configuration (Long Description) Short Descrip- tion Kit 2003-Later FLST/C and 2003-2005 FX Softail Models (Except FXSTD) With Other Detachable Accessories FL Outer 88237-07 2003-Later FLST/C and 2003-2005 FX Softail Models (Except FXSTD) Without Other Detachable Accessories FL Inner 2003-Later FLST/C and 2003-2005 FX Softail Models (Except FXSTD) With Rigid-Mounted Accessories FL Rigid 2006-Later FX Models (Except FXSTD) With Other Detachable Accessories FX Outer 88238-07 2006-Later FX Models (Except FXSTD) Without Other Detachable Accessories FX Inner 2006-Later FX Models (Except FXSTD) With Rigid-Mounted Accessories FX Rigid 2007-Later FXSTC Models With Stock Passenger Upright FXSTC Stock NOTE Proper installation of these kits requires that tasks be completed for one side of the motorcycle first before continuing to the opposite side. Install Turn Signal Relocation Kit Refer to instructions included with Turn Signal Relocation Kit 69857-07. Install Docking Hardware Kit(s) Without Other Detachable Accessories: Refer to instructions included with Docking Hardware Kit 53932-03. With Other Detachable Accessories: Refer to instructions included with Docking Hardware Kits 53932-03 and 88256-07. Install Rear Docking Adapter NOTE This procedure only applies to models without detachable accessories. 1. See Figure 1. Insert rear docking adapter (1) into holes in saddlebag bracket and hold in place. 2. Install rear docking adapter using screw (2) and nut (3). Tighten snugly.

DETACHABLE KING SIZE WINDSHIELD FOR SOFTAIL MODELS WITH CHROME HEADLAMP NACELLE OR STREET STALKER HEADLAMP NACELLE (WITHOUT PASSING LAMPS)

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download
Installation 1. Remove upper screws that attach the chrome headlamp nacelle to the front forks. 2. See Service Parts illustration. Attach the upper docking bushings (22) using washer (21) and mushroom head screws (20) Use Loctite 242 (blue) on screw threads. Torque screws to 19 ft-lbs (25.8 Nm). 3. Remove lower screws that attach the chrome headlamp nacelle to the front forks. 4a. For vehicles equipped with the Chrome Headlamp Nacelle, attach the lower docking bushing (22) using washer (21) and button head screw (23). 4b. For vehicles equipped with the Street Stalker Headlamp Nacelle, attach the lower docking bushing (22) using washer (21) and button head screw (24). Installing/Removing Windshield 1. Carefully lock bottom windshield assembly jaws into grooves of the lower rubber docking bushings. 2. Hook the top windshield assembly jaws into grooves of the upper rubber docking bushings. 3. Firmly press the windshield into place until seated on docking bushings. 4. To remove windshield, grab windshield edges on each side of center brace and firmly pull windshield loose from docking bushings. 1 WARNING Carefully inspect windshield upon completion of installation. Be sure windshield mounting does not restrict full left or full right movement of front fork assembly. Restricted movement could affect handling, resulting in personal injury. If restriction does occur, adjust windshield as needed until proper clearance is obtained. Have experienced Harley-Davidson service personnel correct any problems before riding with this accessory installed. 1 CAUTION Check mounting hardware periodically. Never ride with loose mounts. A loose mounting causes extra stress on all other mounts, as well as the windshield itself, and could result in premature failure of either or both. 1 CAUTION Do not clean Lexan®polycarbonate in hot sun or high temperature. Powdered, abrasive or alkaline cleanser will damage the windshield. Never scrape the windshield with a razor blade or other sharp instruments because permanent damage will result. Sunlight reflections off of the inside curvature of a windshield can, at certain times of the day, cause extreme heat build-up on motorcycle instruments. Exercise care in parking. Park facing the sun, place an opaque object over the instruments, or adjust the windshield to avoid reflections. Harley-Davidson windshields are made of Lexan®. Lexan®is a more durable and distortion-resistant material than other types of motorcycle windshield material, but still requires attention and care to maintain. • Do not use liquid windshield “protectors” on your windshield. Although they may work well on automobile safety glass, Harley-Davidson cannot ensure the results when used on Lexan®Harley- Davidson windshields. If you want to use a windshield protectant on your windshield, try Harley Glaze Polish and Sealant®. • Do not use benzine, paint thinner, gasoline, or other types of harsh cleaning agents on windshield. They will damage the windshield surface. • Do not use benzine, paint thinner, gasoline, lubricants (including Armorall), or other cleaning agents on the rubber bushings. They will damage the bushing surfaces

Incoming search terms:

HARLEY DAVIDSON SOFTAIL DETACHABLE WINDSHIELD INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
INSTALLATION NOTES To prevent scratches, cover the headlamp and the front of the fuel tank with a clean cloth and be sure the windshield assembly does not contact chrome or painted parts when removing or installing it. 1. Remove the original equipment windshield, if equipped. Discard the windshield and attaching hardware. 2. See Figure 1. Remove and discard screws and washers securing trim strip (6) to the front and rear trim pieces. 3. Peel protective cover from adhesive side of clear tape. Center tape over front panel trim piece, attach tape to trim piece, wrap tape edges around trim piece and attach to back of trim piece. Leave the protective tape on the trim pieces after kit installation. 4. Install a flat washer (2), bushing (3) and thick washer (4) onto mushroom screw (1), then install the screw into the upper hole of the trim strip (6) and front and rear trim pieces. Do not tighten screw. 6 1 4 2 3 5 4 2 3 is02411a 1. Mushroom head screw (2) 2. Flat washer from kit (4) 3. Docking point bushing (4) 4. Washer, thick (4) 5. Button head screw (2) 6. Front panel trim strip Figure 1. Front Panel Trim Strip and Windshield Dock Installation 5. Install a flat washer (2), bushing (3) and thick washer (4) onto button screw (5), then install the screw into the lower hole of the trim strip (6) and front and rear trim pieces. Tighten screws to 96 in-lbs (10.8 Nm) . 6. Repeat procedures 2 – 5 on the opposite side. 7. Lock the bottom windshield assembly jaws into the grooves of the lower rubber docking bushings on each side of the front fork assembly. 8. Hook the top windshield assembly jaws into the grooves of the upper rubber docking bushings. 9. Firmly press the windshield into place until it is seated on the docking bushings. 10. Tighten the upper screws to 96 in-lbs (10.8 Nm) . Improper installation of accessories or loading of cargo can affect motorcycle stability and handling, which could result in death or serious injury. (00455b) Failure to provide adequate clearance between stationary and moving parts can cause loss of control, which could result in death or serious injury. (00378a)

HARLEY DAVIDSON TOUR-PAK KIT INTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
INSTALLATION 1. Remove the rubber mat from the bottom of the Tour-Pak. 2. See Figure 1 and Table 1 to determine the proper hole configuration to attach the Tour-Pak to your luggage rack. Holes will be drilled as explained in Step 3 in the hole location for your luggage rack. Table 1. Luggage Rack and Hole Configurations Hole Configura- tion Luggage Rack C (3 holes) Stock 1997 B (4 holes) Detachable luggage rack 53107-96 A (5 holes) Luggage rack 53118-97A and luggage rack 53118-98 A (5 holes) Stock 1998 and later racks A (5 holes) Detachable Tour-Pak rack 53276-04 B (4 holes) Solo detachable Tour-Pak rack 53655-04 B (4 holes) Detachable Tour-Pak rack 53066-00B B (4 holes) Solo detachable Tour-Pak rack 53559-04A A (5 holes) Solo detachable Tour-Pak rack 53260-02 -J03631 1 of 3 B 1 A C 2 2 2 is00163 1. Front of motorcycle 2. Bottom view of Tour-Pak interior (rubber mat removed) Figure 1. Hole configurations for Tour-Pak attachment NOTE Drilling holes in Tour-Pak without wood underneath each hole site may result in the leather becoming damaged during the drilling process. 3. Place blocks of wood underneath the Tour-Pak where the holes will be drilled to prevent damage to the leather while drilling. Use the pre-drilled holes in the metal base as a guide and carefully drill the holes through the leather in the proper location using a 11/32 inch drill bit. 4. See Figure 2. For detachable luggage racks (53107- 96, 53066-00B and 53276-04): Install black cover tube to the front bar (1) of the luggage rack, as shown. This tube is used to provide a cleaner look. The black cover tube is not for use with other luggage racks. 5. Attach Tour-Pak to rack using the mounting screws provided in the Luggage Rack kit. Put bolt through from inside of Tour-Pak. Tighten screws to specifications found in the Luggage Rack kit. 6. Place the black rubber mat on the bottom of the Tour-Pak. 7. If luggage rack was removed, reattach to motorcycle according to kit instructions or Service Manual instructions

HARLEY DAVIDSON TOURING DETACHABLE SISSY BAR UPRIGHTS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
INSTALLATION NOTE The Detachable Sissy Bar Upright can be installed on either a two-point or four-point Docking Kit. 1. If not already in place, install the Detachable Docking Hardware Kit (either two-point or four-point) to the vehicle per the instructions in that kit. 2. See Figure 2. While standing behind the motorcycle, place the left-side and right-side front upright notches (with bushings in place) onto the docking points (A) inboard of the upper shock absorber mounts. Make sure the notch bushings (9) seat fully into the shock absorber docking points. 3. See Figure 2, arrows (D) and (E), and Figure 1. Position the rotary latches (4) over the rear docking points (3). Check to be sure the upright sides (1) and latches fit into the neck (7) of the rear docking points as shown. This may require some gentle squeezing or spreading of the sissy bar upright sides. NOTE After installing the sissy bar upright, check to be sure the sissy bar is secure. The front and rear docking points must be fully engaged. See Figure 1 for correct engagement. 4. Push the rear of the sissy bar downward and close the latches by pressing the latch lever as far forward as it will go. You will hear a “CLICK” when the latch is in place. If the latch does not easily close, do not force. Check the sissy bar alignment again, as described in steps 2 and 3. 5. To remove the sissy bar upright, press the release button (G) on each side and pull the latch levers back. Carefully lift the rear of the sissy bar up and pull the upright out of the front docking points

HARLEY DAVIDSON DETACHABLE DYNA SIDEPLATE KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
Additional Parts Required The appropriate docking hardware and possibly a directional relocation kit must be installed prior to installation of this side- plate kit. These kits must be purchased separately from a Harley-Davidson Dealer. Table 1. Docking Hardware Kits Model Year Docking Hardware Kit FXDWG 53964-06 only Table 2. Directional Relocation Kits Model Year Docking Hardware and Directional Relocation Kit All except FXDWG 53961-06 and 53968-06 If mounting this kit with Saddlebags, part number 53968-06 is not required. Loctite® 262 (red), Part Number 94759-99, is available from your Harley-Davidson Dealer. Kit Contents Table 3. Kit Contents Part Number Description (Quantity) 52869-06 Side Plate, detachable, right 52870-06 Side Plate, detachable, left 94592-98 Button head screws (4) SISSYBAR INSTALLATION 2 3 1 4 1 is 01079 1. Sideplate 2. Sissybar 3. Buttonhead screw 4. Rotary latch Figure 1. Detachable Sissybar Sideplate Assembly See Figure 1. Install new or existing sissybar (2) to detachable sideplates (1) using four buttonhead screws (3). Apply Loctite® 262 (red) to screws before installation. Tighten screws to 96- 120 in-lbs (11-14 N-m)

HARLEY DAVIDSON SOFTAIL DETACHABLE TWO-UP TOUR-PAK LUGGAGE RACK INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download

TOUR-PAK LUGGAGE INSTALLATION TO RACK 1. Open the lid and, if necessary, remove all items from inside the Tour-Pak luggage.  Remove the rubber mat from the luggage floor. 2. If holes ARE NOT pre-drilled in the floor of the luggage,       see Figure 1. To prevent damage to the leather while drilling, place blocks of wood underneath the Tour-Pak luggage at the drilling sites.  Use the four inboard holes (3) in the metal base of the luggage (2) as a guide, and carefully drill four 11/32 inch (9 mm)  holes through the floor of the luggage. 1 2 3 is04249 1. Front of motorcycle 2. Tour-Pak 3. Drill four 11/32 inch (9 mm) diameter holes Figure 1.  Drill Attachment Hole Locations in Tour-Pak NOTE See Figure 3. When installing the luggage to the rack in the following steps, note that holes in the luggage rack (2) provide forward (A) and rearward (B) positions for mounting the lug- gage. 3. Place the luggage on the luggage rack.  Align the holes in the luggage mounting plate with the forward or rearward holes in the rack. 4. ALL applications: Obtain the hex head cap screws (9), lock nuts (11) and plain washers (10) from the kit. Place a washer over the threads of each screw, and insert the screw threads, from the inside, through the Tour-Pak luggage mounting plate and floor, and into the holes in the rack. NOTE Always install the mounting screws from inside the luggage.  If the screws are installed from the bottom, the screw ends can tear the rubber mat and scratch objects, such as helmets, stored inside the luggage. 5. From the underside of the rack, install a washer and lock nut onto the threads of each screw.  In a crosswise pattern, incrementally tighten each screw to 19 ft-lbs (25 Nm) . 6. Install the rubber mat into the luggage.  Close and latch the lid. 7. If not already in place, install the Detachable Docking Hardware Kit to the vehicle per the instructions in that kit

HONDA GL18000 DRIVER BOARDS REPLACEMENT RUBBER PADS INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 29-01-2011

download
1. Remove any loose pads, remove any remaining rubber & glue using a blade screwdriver or razor blade. 2. Rough up the chrome surface with sand paper or by scratching with the tip of a screw driver. 3. Clean any remaining glue residue off using acetone solvent or nail polish remover. 4. Clean both the floorboards and the back side of the rubber pad with rubbing alcohol. 5. Using the supplied small brush and tube of 3M weather strip adhesive, apply a thin layer of glue to both the floorboard and the backside of the rubber pad or pads. Allow to dry for 10-15 minutes or until tacky to the touch. Apply a second thin coat to both surfaces and while still wet press the rubber firmly into place and keep pressure applied evenly for 45-60 seconds

HARLEY DAVIDSON DETACHABLE LOCK KITS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-02-2011

download
REMOVAL 1. Remove the detachable accessory by pressing the release button on each side and pull the latch levers back. Lift the rear of the accessory up and pull the rack off of the front docking points. 2. See Figure 1. Remove the screw (1) and washer (2) from the latch(es) to be replaced by the new locking latch. Save the screw and washer for installation. INSTALLATION See Figure 8. Depending on the installed detachable, the position of the relief (A) and undercuts (B) will be used as spacers or docking point mounts. Verify that the locking latch is positioned so there is key access for unlocking the latch. NOTES Verify that the locking latch is in the unlocked position before installation. Do not leave the key inserted in the locking latch during assembly. Detachable styles may vary from those shown in the illustra- tions. Outer Right Upright Installation 1. Remove right non-locking latch. 2. See Figure 2. Install stock spring washer (2) on mounting hub. 3. Install flat washer (4) (from kit) on mounting hub. 4. Install latch with relief away from the outer right sideplate. 5. Install stock screw (3) and washer (1). 6. Tighten screw to 30-40 in-lbs (3.4-4.5 Nm)

HARLEY DAVIDSON HANDLEBAR POLYURETHANE RISER BUSHING KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-02-2011

download
INSTALLATION NOTES • Cover fuel tank with blanket or towels to keep paint from being scratched. • See the Touring Service Manual for the Fairing Removal procedure in order to gain access to the handlebar assembly. 1. For Touring Models: See Figure 1. Remove and save the the existing capscrews (C). Remove the handlebar assembly (A) and carefully allow gauges and handlebar to rest on motorcycle. Remove and discard cup washers (D), rubber bushings (E) and spacers (F). Install the new bushings. For All Models Except Touring: Remove and save the two capscrews (C) from underneath the upper fork bracket that hold the existing lower clamps (risers) (B) in place. Remove the handlebar assembly (A) and carefully allow gauges and handlebar to rest on motorcycle. Remove and discard the existing cup washers (D), rubber bushings (E) and spacers (F). NOTE The upper bushing and lower bushing must be oriented with flat side opposite from each other as shown. 2. Install the new polyurethane riser bushings (1) in place of the removed cup washers, bushings, and spacers. 3. Align components as shown in Figure 1. 4. Secure components with two hex head capscrews removed in Step 1. Insert the capscrews, from the bottom, thru the upper fork bracket, thru the bushings (1) and into the clamps (risers). See the service manual for the torque specification. 5. See the service manual and install the handlebars