can i reverse the risers on a 1996 yamaha virago

You search Auto repair manual PDF can i reverse the risers on a 1996 yamaha virago, if there are search results will appear below. If search results do not exist, please search by others keyword.



  can i reverse the risers on a 1996 yamaha virago Direct Download speed 5282 Kb/s

  can i reverse the risers on a 1996 yamaha virago Full Version speed 6162 Kb/s



YAMAHA ROAD STAR HANDLEBAR RISERS INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 29-01-2011

download
1. Place a blanket folded several times over the fuel tank to prevent any damage during the installation of the risers. Loosen the two 19mm riser mounting nuts located on the bottom side of the upper steering head. Pry out the chrome plugs from the heads of the four handlebar top clamp bolts using a knife blade. Loosen the four handlebar top clamp 6mm socket head screws. 2. It will help having a second person to hold the handlebars while you change the risers. Remove the four screws from the clamps and then the clamps. Pull the handlebars up off the risers, pull them back and rest them on top of the blanket. 3. Remove the nuts from the bottom of the risers and remove the risers. Insert the two supplied spacer tubes into the riser mounting holes on the upper steering head. Using the bolts, lock washers and washers supplied install the new risers making the bolts finger tight only. (Take care not to scratch the top surface of the upper steering head while installing the new risers.) 4. Place the handlebars back up onto the new risers. Reinstall the top clamps using the four socket head screws removed earlier. Set the height of the handlebars to the desired position, tighten the front bolts first and then the rear securely. (15-18 ft. lbs. There should be no gap between the riser and clamp at the front side.) Tighten the two riser mounting bolts securely. (20-25 ft. lbs.) 5. Turn the handlebars all the way to the left and then right checking for any pulling or binding of the wires, hoses or cables. Also check that the throttle returns freely on it’s own

TRIUMPH AMERICA AND SPEEDMASTER HANDLEBAR RISERS INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 29-01-2011

download
1. Place a blanket folded several times over the fuel tank to help prevent any damage during the installation of the risers. Loosen the two 14mm riser mounting nuts located on the bottom side of the upper steering head. Loosen the four handlebar top clamp 6mm socket head screws. 2. It will help having a second person to hold the handlebars while you change the risers. Remove the four screws from the clamps and then remove the clamps. Pull the handlebars up off the risers, pull them back and rest them on top of the blanket. 3. Remove the nuts from the bottom of the risers and remove the risers carefully without allowing the risers to rotate, as this will scratch the clear coating on the upper steering head. Using the bolts, lock washers and washers supplied install the new risers making the bolts finger tight only. (NOTE; again, take care not to allow the risers to rotate as this will scratch the clear coating on the upper steering head). 4. Place the handlebars back up onto the new risers. Install the new top clamps supplied using the four M8 X 30mm socket head screws supplied. Set the height of the handlebars to the desired position, tighten the front bolts first and then the rear securely. (15-18 ft. lbs.) (There should be no gap between the riser and clamp at the front side) Tighten the two riser mounting bolts securely. (20-25 ft. lbs.). 5. Turn the handlebars all the way to the left and then right checking for any pulling or binding of the wires, hoses or cables. YOU MUST! Check to see that the throttle returns freely on its own when the handlebars are at full left and full right turn THIS STEP IS VERY IMPORTANT FOR OBVIOUS SAFETY REASONS! If you have a windshield installed it may be necessary to reroute the throttle cables, wires or hoses around the other side of the windshields mounting hardware to obtain adequate free play and free throttle return. You may also wish to remove the plastic clips or cable tie which secure the wiring to the handlebars and secure them to the brake hose and clutch cable (not the throttle cables) for a cleaner appearance

HARLEY-DAVIDSON 5 and 6 Speed OEM Transmissions ReverseGear User Operating Instructions

0

Filed Under (Harley Davidson) by admin on 16-02-2011

download
A. It is good practice to first engage first gear to stop the gearbox from spinning (This will prevent the “grinding” noise when reverse gear is engaged) and then place the bike in neutral and immediately engage reverse. If Reverse Gear still “grinds” after the above procedure – check the clutch adjustment to ensure the clutch is not dragging and causing the gearbox shafts to spin. B. Do not let the bike “free wheel” backwards while in reverse gear and the clutch engaged or disengaged (i.e. when rolling down a slope when in reverse) – The reverse gear will automatically try to disengage and will result in a “grinding” sound. To prevent this – Always stop immediately after the reverse action is completed. WARNING! Reverse gear is intended for light duty use only – like slowly backing in/out of parking spaces etc. Do not drive for long periods in reverse. WARNING! Do not attempt to engage reverse while the motorcycle is up on a lift stand. Maintenance Check transmission fluid levels regularly and fill with Manufacturer’s suggested lubricants. Warranty One year on reverse gear parts only. Champion will not warranty the Reverse Gear if it is deemed to be “abused” by the user like: – Engaging First Gear while the Reverse Gear is still engaged and/or – Over powering the Reverse Gear by revving and dropping the clutch and/or – For an Installation Error (not following the installation instructions exactly). Any attempt to modify this product without written permission from the manufacturer will void the warranty and may cause damage to vehicle and injury to persons.

Incoming search terms:

1981-1983 Yamaha Virago 750 & 920 Installation Instructions

0

Filed Under (Yamaha) by admin on 11-02-2012

download
Start by loosening the rear cylinder down tube bolt located on the top of the old mufflers center collector in front of the rear tire. 2. Remove both of the front cylinder exhaust pipe head nuts and set them to the side for reuse with the MAC exhaust system. 3. Remove the right side passenger’s foot peg. Set the foot peg aside as you will need to reinstall it. 4. Remove the left side passenger’s foot peg. Set this foot peg aside as it will also need to be reinstalled. Note: When you remove this bolt the entire exhaust system will be loose and may fall. You will need to support the old exhaust at this point to keep from injuring yourself. Gently move the old exhaust system side to side to remove it from the rear cylinder down tube. Once the exhaust system is loose from the down tube remove the system from under the Virago. 5. Remove the bolt holding the rear brake pedal in place and remove the brake pedal from the motorcycle. Note: Set both the bolt and the pedal aside for reinstallation. 6. Next loosen the nut on the drivers right foot peg, 1 full turn to start with. Then remove the rear nut on the same foot peg. (Note: The bolt that this nut is on goes completely through the motorcycle. This is the center stand mounting bolt.) Now remove the front nut and set both aside for reuse with the MAC system. 7. Install the center stand stop bracket under the left passenger foot peg. Install this bracket with the 90° bend facing down and towards the rear tire. (Note: Center stand sop bracket in provided in the hardware kit and is approx. 5″ long with a 90° bend in it.) Adjust the bracket by one of the large bolts through the foot peg then through the bracket and then install it into the stock location. Put on one of the washers and a nut and snug up the nut. Lower the center stand until the center stand come in to contact with the bottom of the bracket. Tighten the nut until it will hold the bracket securely. 8. Install the rear down tube clamp onto the rear muffler and install the medium sized nut/bolt/washer onto the clamp just finger tight. 9. Install the (2) small bolts into the channel bracket on the rear muffler. Install the rear mounting bracket onto the two bolts and then install the washers and nuts onto each. Tighten the (2) nuts only slight amount so that you can slide the bracket front to rear to insure that when you install the bracket you position it properly. 10. Slide the rear pipe onto the rear down tube about ¼”to ¾” past the pre-cut slots on the rear muffler pipe. Slightly snug the clamp making sure that the position of the bolt and nut will not interfere with any moving parts. The final position of this bolt can hit the tire if it is not positioned properly. 11. Install the other large bolt into the right passenger and then through the top hole in the rear muffler mounting bracket. Insert the bolt into the stock location and install the washer and the nut. 12. Align the rear muffler and you can then tighten the nuts on the rear muffler mounting bracket, the cylinder down tube and the right side passenger foot peg.
13. Install the front muffler on the rear most mounting bolt of the drivers foot peg and put the stock nut back onto the bolt. Hand tighten the bolt only at this time. Note: Install the nut at this time is only to support the muffler and to insure that the pipe does not fall on the ground while you complete the next step. 14. Lift the front head pipe into position and start the stock nuts onto the studs. It is strongly recommended that you install new exhaust gasket at this time. Note: The new exhaust gaskets are not included in the kit but are available at your local Yamaha Dealer. After gaskets are installed hand tighten the front head pipe. 15. Remove the nut from the drivers foot peg bolt and reinstall the drivers foot peg. Note: Hand tighten only at this time. 16. Finish tightening the nuts on the front head pipes. (Install these nuts according to Yamaha’s Factory specifications.) Once the nuts are tightened on the head pipe you can then tighten the drivers foot peg nuts. 17. Reinstall the rear brake pedal and tighten the bolt that holds it on to factory specifications. 18. Check all of the bolts that you have installed of removed to insure that they are tight. 19. Start the motorcycle and check for any leaks. 20. You are finished with your new MAC Exhaust System.

Incoming search terms:

Triumph Rocket III Touring HANDLEBAR RISERS INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 29-01-2011

download
1. Place a blanket folded several times over the fuel tank to help prevent any damage during the installation of the risers. Using a small screwdriver pry out the plastic caps covering the handlebar clamp bolts. 2. Reroute the clutch cable behind the steering head as follows. Remove the clutch cable from the lever and perch. To do this first loosen the cable adjuster lock nut and then the adjuster as far as possible to give its maximum free play. Align their slots with the slot in the perch so that the cable may slide out. Standing in front of the handlebars grasp the clutch cable firmly trying to pull it out of the adjuster with one hand while pulling in the lever with the other hand. Now release the lever rapidly. Repeat several times if needed while keeping outward tension on the cable until the cable is out of the adjuster then slide it out thru the slots and remove the cable end from the lever. Reroute the clutch cable behind the steering head this will allow the additional slack needed when moving the handlebars back with the new risers (see photo). Replace the cable into the perch in the same manner. 3. It will help having a second person to hold the handlebars while you change the risers. Remove the four Allen bolts from the clamps and then remove the clamps. Pull the handlebars up off the risers, pull them back and rest them on top of the blanket. 4. Remove the Allen bolts from the center of the risers while holding the 14mm nut on the bottom side of the steering head with a wrench. Remove the risers leaving the large washer on the top side of the steering head in place. Using the bolts and lock washers supplied and the original heavy or thick washer install the new risers making the bolts finger tight only. 5. Place the handlebars back up onto the new risers. Install the new top clamps supplied using the four Allen bolts remover earlier. Set the height of the handlebars to the desired position, tighten the front bolts first and then the rear securely. (15-18 ft. lbs.) (There should be no gap between the riser and clamp at the front side) Tighten the two riser mounting bolts securely. (20-25 ft. lbs.). Replace the plastic bolt caps.

HARLEY DAVIDSON FXD HANDLEBAR RISERS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-12-2010

download
Place a blanket folded several times over the fuel tank to help prevent any damage during the installation of the risers. Using a æ” socket loosen the two riser mounting bolts located on the bottom side of the upper steering head. Using a º” hex key wrench loosen the four handlebar top clamp bolts. 2. It will help having a second person to hold the handlebars while you change the risers. Remove the four bolts from the top clamp and then remove the clamp. Pull the handlebars up off the risers, pull them back and rest them on top of the blanket. 3. Remove the bolt from the bottom of one of the risers and remove the riser while keeping the bolt in place. Place one of the supplied Ω” washers onto the protruding bolt, and then the new riser (Note; There are LEFT & RIGHT risers.) and mount the bolt finger tight. (Take care not to scratch the top surface of the upper steering head while installing the new risers.) 4. Place the handlebars back up onto the new risers. Install the top clamp using the supplied four black 5/16-18 X 1 º” bolts. Set the height of the handlebars to the desired position; tighten the clamp bolts evenly making sure the gap between the clamps & risers are the same. (15-18 ft. lbs.) Tighten the two riser mounting bolts securely. (20-25 ft. lbs.). 5. Turn the handlebars all the way to the left and then right checking for any pulling or binding of the wires, hoses or cables. Also check that the throttle returns freely on its own

YAMAHA CRANKSHAFT LOWER END REMOVAL AND INSTALLATION TOOLS

0

Filed Under (Yamaha) by admin on 08-01-2012

download
90 LOWER END REMOVAL & INSTALLATION TOOLS SHOP EQUIPMENT & TOOLS 35-8399 35-8513 35-8516 35-8508 35-8504 35-8507 YAMAHA CRANKSHAFT PROTECTORS Sold each. 35-8504 YM-4063-A, XV750/920 Virago, XT550, YFP350, YFM660R Raptor 35-8399 YM-1382, XT250/XT350, RZ350, YFP350, YFZ350 35-8507 YM-33282, XV500 Virago, XZ550 Vision, XVZ12/13 Venture & Venture Royale, VMX12 V-Max 35-8508 YM-38145, XV750/XV1000 Virago YAMAHA CRANKSHAFT INSTALLATION SET Sold as a set. Consists of the following: Qt1-Installing Pot, Qt1-Pot Spacer, Qt1-Bolt. 35-8509 YU-90050 Crankshaft Installation Set OPTIONAL POT SPACERS 35-8513 YU-90070-A, XV750/920 Virago, XT550, TT600 35-8515 YU-91044, YFM350, SRX600, XT550/600 35-8516 YU-1202, SR500, TT/XT500 CRANKCASE PRESSURE TESTER An accurate method for checking possible air leaks on two-stroke engines. Complete with air pressure gauge, pump-up bulb and all fittings and adapters for single and multi-cylinder two-cycle engines. 35-5962 Crankcase Pressure Tester CRANKSHAFT INSTALLING JIG TOOL Supports and centers crankshaft webs while assembling two-stroke engine cases and rebuilding crankshafts. Prevents rod misalignment. Adjustable tang ends. 35-9804 Crankshaft Installing Jig Tool CRANKCASE SEPARATOR TOOL This tool will work on most two and four stroke engines that have a vertically split crankcase. Moveable fingers allow a multitude of bolt patterns to be used so it will work on a variety of models. Includes 6mm and 8mm mounting bolts, center pulling bolt and a three leg frame that is appropriate for many applications. 35-9642 Crankcase Separator Tool 35-9637 Replacement 6mm and 8mm mounting bolts. Each

HONDA VTX1300, VTX1800 R, C & S MODEL HANDLEBAR RISERS INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 27-12-2010

download
1 .Lay a blanket folded several times over the fuel tank to protect it. 2. Notice on the 1800 models that there is a small punch mark on the handlebars located on the right hand, front side of the handlebars where the risers meet the top clamp/speedometer housing. This is to reference the handlebar position when re-assembling. On the 1300 models there is a punch mark on the forward facing side of the clamp, these must be installed the same way. 3. Loosen the two 19mm nuts holding the risers to the upper triple clamp (steering head). 4. Pry out the four chrome caps covering the handlebar bolts. Remove the four handlebar clamp bolts. (6mm allen wrench). While sitting on the motorcycle, pull the handlebars and upper clamp off of the risers. They may be slightly stuck and require some force to get free. Lay the handlebar and/or upper clamp/gauge assembly carefully on the blanket. 5. Remove the 19mm nuts and the risers from the triple clamp. NOTE: Be careful not to scratch the upper triple clamp when installing the new risers. Place the thin flat washers provided into the recess at the top of the riser bolt holes on the triple clamp. Assemble the lock washers provided and then the original flat washers onto the bolts provided. Install the new risers onto the triple clamp and snug the bolts. 6. Re-install the handlebars and upper clamp/gauge assembly. ( Remember the punch marks) Tighten the front bolts first closing the gap at the front, and then tighten the rear bolts. Tighten the two 19mm riser-mounting bolts securely. Check for adequate clearance and proper routing of cables and hoses.

HARLEY DAVIDSON PULLBACK RISER KIT FOR 1.25-INCH HANDLEBARS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-02-2011

download
REMOVAL NOTES Cover the fuel tank with clean shop towels to prevent scratching. If replacing the handlebar, refer to the service manual to remove controls, hand levers, handlebar and risers. If only the risers are being replaced, proceed as follows: 1. Remove the two hex head cap screws and split lock- washers on the underside of the upper fork bracket that hold the currently installed risers in place. Discard the screws, but retain the lockwashers for assembly. Retain all additional components from the riser assembly when the screws are removed. 2. Remove and discard the four screws that fasten the currently installed handlebar upper clamp(s) to the risers. Remove and discard the clamp(s). Remove the handlebar from the risers and carefully set the handlebar on the fuel tank. INSTALLATION NOTES See Figure 3. The upper cup washer (A) must be oriented with the flat side up and the lower cup washer (D) with the flat side down. 1. See Figure 3. Align the components as shown, and install the risers (2) to the upper fork bracket. The ground wire (G) and the lock washer (F) are located on the right side only. Do not tighten the riser mounting screws (4) at this time. 2. If an appropriate Harley-Davidson 1-1/4 inch handlebar has not been installed, install one according to the Instruction Sheet included with the kit, or install the handlebar assembly onto the risers. 3. Loosely install riser caps (1) onto the handlebars and risers with the Bar & Shield toward the front of the motorcycle (Figure 1, Item 1). Install four socket head screws (3) with four washers (6). 1 is05253 1. Bar & Shield (install toward front of motorcycle) Figure 1. Bar & Shield on Riser and Cap 4. Check that the risers stay properly aligned with the handlebar and tighten the riser mounting screws following the instructions in the service manual. 5. Adjust handlebar to the desired position, verify that it is centered on the risers, then tighten the front socket head screws (3) to 12-15 ft-lb (16-20 Nm) . There should be no gap at the front of the risers.

Incoming search terms:

YAMAHA MOTOR CORPORATION, U.S.A. STREET & ENDURO MOTORCYCLE LIMITED WARRANTY

0

Filed Under (Yamaha) by admin on 27-12-2011

download
GENERALEXCLUSIONS from this warranty shall include any failures caused by: a. Competition or racing use. b. Installation of parts or accessories that are not qualitatively equivalent to genuine Yamaha parts. c. Abnormal strain, neglect, or abuse. d. Lack of proper maintenance. e. Accident or collision damage. f. Modification to original parts. g. Damage due to improper transportation. SPECIFIC EXCLUSIONS from this warranty shall include parts replaced due to normal wear or routine maintenance. THE CUSTOMER’S RESPONSIBILITY under this warranty shall be to: 1. Operate and maintain the motorcycle as specified in the appropriate Owner’s Manual. 2. Give notice to an authorized Yamaha motorcycle dealer of any and all apparent defects within ten (10) days after discovery, and make the machine available at that time for inspection and repairs at such dealer’s place of business. You may locate your nearest authorized Yamaha dealer through your local telephone directory. WARRANTY TRANSFER: To transfer any remaining warranty from the original purchaser to any subsequent purchaser, it is imperative that the machine be inspected and registered for warranty by an authorized Yamaha motorcycle dealer. In order for this warranty to remain in effect, this inspection and registration must take place within ten (10) days after transfer. Areasonable dealer imposed fee may be charged for the inspection. In no case will warranty be extended beyond the original period. EMISSIONS CONTROLSYSTEM WARRANTY Yamaha Motor Corporation, U.S.A. also warrants to the ultimate purchaser and each subsequent purchaser of each Yamaha motorcycle covered by this warranty with a displacement of 50cc or greater, that the vehicle is designed, built, and equipped so as to conform at the time of sale with all U.S. emissions standards applicable at the time of manufacture and that it is free from defects in materials and workmanship which would cause it not to meet these standards within the periods listed immediately below. Failures other than those resulting from defects in material or workmanship which arise solely as a result of owner abuse and/or lack of proper maintenance are not covered by this warranty.

Incoming search terms: