bmw r850r right head leaks

You search Auto repair manual PDF bmw r850r right head leaks, if there are search results will appear below. If search results do not exist, please search by others keyword.



  bmw r850r right head leaks Direct Download speed 5282 Kb/s

  bmw r850r right head leaks Full Version speed 6162 Kb/s



BMW Motorcycles All R1100 Models- Cylinder Head Gasket

0

Filed Under (BMW) by admin on 16-11-2010

download
Situation: All R1100 models produced from calendar week 18 (April 28, 1997) onwards will be equipped with head gaskets of Multi-Layered Steel (MLS) technology. Service Information: The MLS cylinder head gasket can be used in place of all earlier gaskets, on all R1100 models, without any modifications. Part Number: MSL cylinder head gasket for all R1100 models. P/N: 11 12 1 341 173 Note: The MLS cylinder-head gasket is applicable to R1100 models only. If it becomes necessary to replace cylinder-head gaskets on R850 R models, the conventional gasket, P/N 11 12 1 342 082, must be used. Warranty Processing: If your retail center has any quantity of the conventional head gasket for the R 1100 models, P/N: 11 12 1 342 127, in stock, please file a warranty claim using the information below. If your retail center has the engine gasket set, P/N: 11 00 1 341 901 in stock , please make sure that the new style MLS gaskets are used in place of the conventional head gasket supplied in this set. All current BMW NA inventory of P/N 11 00 1 341 901 will have the MLS head gasket included. Defect Code: 00 11 01 00 00 Frame Number: 4990150 Warranty Type: 2 Warranty Stage: 1 Very truly yours,

Incoming search terms:

KAWASAKI VULCAN 700/750 CRUZER EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 28-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Place the bike on the center stand. 2. Remove the three clamps attaching the heat shield to the left hand head pipe and set the heat shield aside. 3. Remove the two heat shield clamps attaching the heat shield to the right hand head pipe and set the heat shield aside. 4. Loosen the pinch clamps where the mufflers slip onto the muffler box (the black box in front of the rear tire). Remove the bolt attaching the mufflers to the footrest. 5. Remove the left and right hand mufflers and set them aside. 6. Remove the right hand foot rest and brake pedal assembly from the frame. 7. Loosen the pinch clamps where the head pipes slip into the muffler box. 8. Remove the two nuts that secure the right head pipe to the cylinder head. Repeat this step on the left head pipe and save the nuts for reuse. 9. Remove the left and right hand head pipes. Remove the header flange from each head pipe and save the two flanges for reuse. Set the head pipes aside. 10. Remove the two bolts (one on each side) that mount the muffler box to the frame. Lower the muffler box down and set it aside. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Remove the two bolts from the charcoal canister mount, the canister is located in front of the rear tire. Using the two 6mm x 16mm bolts (supplied) install the centerstand stop bracket, (stamped 205), by aligning the holes in the bracket with the holes in the canister mount. Be sure the bend closest to the holes in the bracket angles towards the rear of the motorcycle and the tang is pointed to the left hand side. Tighten the two 6mm bolts at this time. 2. Unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of both heat shields. Place the front head pipe into the heat shield, wrap the hose clamp around the head pipe and give the screw three to four turns. Repeat this step with the rear heat shield. Note : The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. Leave them loose at this time. 3. Install a three hole mounting bracket to each muffler as shown in figure 1. Slide one dog bone shaped nut plate under the bracket that is welded to the backside of each muffler. Attach the mounting bracket using two of the 5/16″ flange head bolts (supplied), leave them loose at this time. Note : The muffler bracket stamped #284 is for the right hand muffler, bracket #285 is for the left hand muffler. 4. Install the rear exhaust assembly, with the heat shield attached, to the rear cylinder using the stock flanges and nuts. Install the stock muffler mounting bolts through the rear footrest brackets, the supplied muffler brackets, and finger tighten the nuts. Leave them loose at this time. 5. Repeat step #4 with the front head pipe

1994 – 2004 BMW Motorcycle History

0

Filed Under (BMW) by admin on 17-11-2010

download
1994 brought many changes to BMW, most obviously by the introduction of the “R259″ series twins and the elimination of the old standby “Airhead” twins that had been BMW’s trademark for seven decades. While it is interesting to look at all the technologies introduced during the 1994 to 2004 time block, it is also exciting to look into what was going on as far as changes in BMW more esoteric than measurable. In this author’s opinion there were unspoken changes in BMW’s mindset and philosophy. BMW had forged it’s reputation for long lasting, simple machines built to the highest standards and quality; aimed at a dwindling, older (OK, Jeff, more mature) market of enthusiastic but eccentric riders. They built motorcycles that were easy for the owners to maintain and modify to fit their specific wants. BMW had always built their bikes their way; often it seemed like they did so in spite of what the younger and upwardly mobile riders were looking for. By 1994, the airhead was simply not a sellable motorcycle; the buying market was younger and wanted performance in line with what the Japanese products offered at much lower prices. The K 75/100 series that were so far ahead of their time in 1984 when they were introduced were also showing their age. No doubt, BMW knew this was coming many years before the new “Oil Head” was introduced. They knew that the riding community had reduced its mean age substantially. The younger riders had money to spend on a bike that had to be BMW, yet had to be totally more modern both in performance and in perception than what BMW had been selling. Thus, the R259 was born. The Birth of the R259 Twins The new BMW corporate mindset, if you will, was no longer concerned with selling motorcycles that would be handed down from one generation to the next, nor was BMW concerned about ease of maintenance with standard hand tools. Although the new bikes were still able to outlast the riders, the concern for building units to last a quarter-million miles was not so much in the forefront of the design. The new models would have to be powerful, fast, handle better than anything on the road; they would need to offer a standard of technology that the Japanese would never build. They should be complex pieces of rolling art. Most obvious, though, was that they would build a product aimed at an entirely new market of riders who would likely not be interested in maintaining the bikes themselves or really understanding the nuances of design. The new customers BMW was looking for were serious riders who were more interested in the fun and excitement of riding than they were in savoring the history of the older designs

Incoming search terms:

HONDA VF750 MAGNA SLIP-ON EXHAUST SYSTEM Installation Manual

0

Filed Under (Honda) by admin on 20-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Remove the left and right side frame covers to prevent damaging them. 2. Loosen the pinch clamps on the inlet end of all four mufflers, located behind the rear motor mount. 3. Remove the left and right front head pipes. 4. Remove the rear mounting bolt from both muffler assemblies. Carefully slide each muffler assembly off the head pipes and set them aside. 5. Replace the front head pipes. Note : Leave the head pipes loose for later adjustment. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of both heat shields. Note : The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. 2. Place the slip-on head tube into the matching heat shield, wrap the hose clamp around the head tube and give the screw three to four turns, leaving heat shield loose on the head tube. Repeat this step with opposite head tube and heat shield. 3. Slide a T-bolt band clamp (supplied) onto the slotted end of each slip-on tube. 4. Slip the slotted end of tube onto the rear head pipes. The shorter of the two slip-on tubes mounts on the right rear head pipe and the longer tube on the left rear head pipe. Tighten the T- bolt clamp until the pipe is snug but so the pipe will still be able to rotate. 5. Install the muffler mounting brackets to the frame using the single hole in the brackets and the stock hardware. The left side mounting bracket (stamped #206 on the bracket) mounts to the outside of the frame, where the stock muffler assembly mounted. The right side bracket (stamped #207) mounts to the inside of the frame, behind the stock muffler mounting point. 6. Slide a chrome muffler clamp (supplied) onto the inlet end of each muffler. Install a 5/16″ x 1 1/4″ bolt with a flat washer on either side of the clamp followed by a lock nut (all supplied). Do this to each muffler but leave the clamp loose at this time. 7. To determine the difference between the left, right, upper and lower mufflers refer to the number stamped on the bracket welded to the backside of each muffler. The top right hand muffler is D500, the bottom right hand muffler is D510, the top left hand muffler is D550 and the bottom left hand muffler is D512. Note : The endcap bolts should face down and inward when viewing from the rear (Refer to Figure 1) .

YAMAHA VIRAGO 700/ 1100 2 into 2 EXHAUST SYSTEM REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 20-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Loosen the slip joint clamp on the front and rear head pipe, which are located at the muffler box. 2. Remove the two nuts that hold the front head pipe to the engine. Slip the head pipe out of the muffler box and set it aside. Note: Do not remove the rear head pipe, it has been incorporated in the design of the new exhaust system. 3. Remove the muffler box mounting bolt located in front of the passenger foot rest on the left side. 4. Remove two bolts from the right passenger foot rest assembly and set the foot rest aside. 5. Slide the muffler box off of the rear head pipe and set it aside. 6. Replace the muffler box mounting bolt (from step #3) using the washer and nut (supplied) on the back side. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Attach the mounting bar to the motorcycle frame behind the right passenger foot rest. Align the two holes in the largest bracket on the mounting bar with the two holes on the frame, be sure the bend in the mounting bar is pointing to the center of the motorcycle. 2. Install the round steel spacer (supplied) to the rear most hole in the bracket. 3. Attach the foot rest using the two 8mm x 1.25 x 25mm bolts (supplied). 4. Slide the new exhaust flange (supplied) onto the front head pipe. 5. Install the two heat shields to the front head pipe using the four hose clamps (supplied). Unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of both heat shields. Place the heat shields onto the front head pipe. Note: Be sure the bend in the heat shield matches the bend in the head pipe exactly. Wrap the hose clamp around the head pipe and give the screw three to four turns, leaving heat shield loose on the head pipe. Repeat this step with the heat shield on the rear head pipe. Note: The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. 6. Check the stock exhaust gaskets to be sure they are in good shape. If you have any doubts as to their condition, replace them. 7. Slide a chrome pinch clamp (supplied) onto the expanded end of the new rear head pipe. Install a 3/8″ x 1″ bolt with a flat washer on either side of the clamp followed by a lock nut (hardware supplied). Repeat this step on the inlet end of each muffler using the two muffler clamps with 5/16″ x 1 1/4″ bolts (hardware supplied) but leave the clamp loose at this time. 8. Slip the new rear head pipe with the heat shield attached, over the stock rear pipe and gasket, but leave the clamp loose at this time. 9. Install the front head pipe, with the heat shield attached and stock gasket in place, to the front cylinder using the stock nuts, leave them loose at this time

Incoming search terms:

BMW Motorcycle F 650 GS/ F 800 GS Accessories

0

Filed Under (BMW) by admin on 20-11-2010

download
Stowage-equipment line Vario case, black, left 71 60 7 696 299 £184 / G Vario case, black, right 71 60 7 696 300 £185 / G (+) Case carrier for Vario case, including fasteners 71 60 7 696 301 £144 / G (+) Lock barrel, complete, for 2 cases 51 25 7 688 566 £20.80 / I (o) Lock barrel by code for vehicle and/or case matching locks (order 2x) 51 25 7 681 199 £33.59 (o) Lock-barrel set 51 25 7 698 202 £15.20 / I Liner for Vario case, left 71 60 7 687 610 £67 / I Liner for Vario case, right, and Vario topcase 71 60 7 687 611 £67 / I Vario topcase, black 71 60 7 696 302 £225 / I (+) Luggage rack, large, for Vario topcase (including adapter plate) 71 60 7 696 303 £64 / I (+) Lock barrel for topcase 51 25 7 688 568 £12.50 / I (o) Lock barrel by code for vehicle and/or case matching locks (order 1x) 51 25 7 681 199 £33.60 / I (o) Lock barrels for 2 cases and topcase 51 25 7 688 567 £29.10 / I Liner for Vario case, right, and Vario topcase 71 60 7 687 611 £67 / I Backrest pad for topcase 71 60 7 688 877 £45 / I Luggage carrier, small 71 60 7 701 810 £42.90 / G Tank rucksack, waterproof 71 60 7 711 240 £130 / I Enduro rear softbag 71 60 7 711 245 £35.90 / I Sport softbag, small, 19 l 71 60 7 694 117 £102 / I Sport softbag, large, 51 l 71 60 7 693 567 £139 / I Stuffbag, waterproof, 53 l 72 60 7 653 818 £90 / I Luggage strap with pull-tight buckle 72 60 2 304 808 £6.30 / E Bungee-cord spider 72 60 9 057 579 £3.95 / E Design line Spray-guard extension, rear 71 60 7 695 031 £24.20 / I Sound components Akrapović sports silencer 71 60 7 713 339 *1 £475 / G Ergonomics and comfort line Windscreen, large, tinted 71 60 7 713 834 *1 £138 / I Windscreen, large, clear (standard for F 800 GS) 71 60 7 713 833 £127 / I Windscreen, small, clear (standard for F 650 GS) 71 60 7 713 296 £87 / I Centre stand (F 650 GS) 46 52 7 700 864 *2 £83 / I Centre stand (F 800 GS) 46 52 7 700 049 *2 £91.50 / I (+) Fasteners for centre stand (F 650 GS + F 800 GS) 71 60 7 706 738 £24.90 / I Seat, low, black, 790 mm (F 650 GS), 850 mm ( F 800 GS) 52 53 7 695 013 £174 / I Heated handlebar grips and switches (see electronic parts catalogue) Navigation and communication components BMW Motorrad Navigator III plus 2008 72 60 7 716 116 *1 £650 / I (+) Holder for BMW Motorrad Navigator 71 60 7 697 785 £45.80 / E (+) Securing screw (order 4 of) 32 71 7 652 161 £4.55 / I Connecting cable for BMW Motorrad Navigator 71 60 7 686 670 £55 / E TMC module for BMW Motorrad Navigator 72 60 7 702 687 *1/3 £111 / E Car kit for BMW Motorrad Navigator 72 60 7 703 996 *3 £60.50 / E Navigator carry-bag function 71 60 7 683 161 £49 / I Safety line Hand-protector bar 71 60 7 716 043 £57 / I (+) Countersunk-head screw (order 2 of) 32 71 7 712 836 £3.34 / E Hand protector, small 71 60 7 705 963 £19.50 / I Hand protector, large 71 60 7 715 135 £23.10 / I Protector-mounted spoiler for hand protector, large 71 60 7 705 964 £15.20 / I Crash bar, left 71 60 7 699 437 £104 / I Crash bar, right 71 60 7 699 438 £104 / I (+) Fasteners for crash bar 71 60 7 702 395

BMW R259 Installation Instructions Fuel Control For BMWOilheads

0

Filed Under (BMW) by admin on 12-11-2010

download
Installation R1200 C -Removethechrome right air filter cover. Release the brake fluid reservoir from its mount. Follow the oxygen sensor lead from the exhaust to the connector. It is mounted to the back of the brake fluid reservoir mounting bracket with cable ties. Cut the cable ties to release the connector from the bracket. Gently pull the connector apart. Insert the male O2 connector from the R259 into the oxygen sensor lead. Connect the female side of the R259sO2 connector to the bike’swiringharness side. Make sure both sets of connectors are fully seated. Cable tie the sensor lead connector back to the bracket and tuck the other O2 connector under the front of theairhorn. -Depressthe retaining bail on the right fuel injector connector and gently pull off the connector. Install this connector on the male R259 injector lead. Install the remaining R259 connector on the right injector. -Connecttheground lead by removing the allen screw (5mmhex) that secures theairboxtothe frame. Place the screw through the lug on the ground lead and reinstall and tighten the screw. Go to section 3 and verify power-up. Tuck the wiring below and behind theairhornand cable tie as necessary. Using the supplied velcro, attach the controller box to the top of theairhorn. Reinstall the brake fluid reservoir in its mount and reinstall the side-cover. Seethe Techlusionwebsite for more detail. Installation R850, R1100, R1150, R1100S -Refertothe appropriate BMW service guides and remove the fuel tank. On some models it maybe possible to have an assistant lift the tank up and to the left to expose the oxygen sensor connector, without fully disconnecting the tank. Locate the oxygen sensor connector by following the lead from the exhaust system. It will be cable tied to the right frame backbone. Cut the retaining cable ties and pull the connector away from the frame. Open the connector and insert the male R259 O2 connector into the oxygen sensor lead, and the female to the bike’swiringharness. Cable tie these back to the right frame backbone. -Routethe R259 wiring harness down the right frame, in-between the battery tray and the rear fuel tank mount. Using the supplied velcro attach the R259 to theairboxlid. Locate the lead on the right fuel injector, and while depressing the locking bail on the connector, gently pull the leadoff. Install this lead on the R259 male injector connector; install the remaining connector on R259 harness to the right injector. Make sure all of the connectors are fully seated. Cable tie any excess wiring away from the fuel lines and throttle mechanism. -Connecttheground lead to the battery negative terminal or an alternate good ground. -Re-install the fuel tank. Make sure the fuel lines are connected and their routing is correct. Insure that both throttle cables are correctly seated in their adjusters on the throttle bodies, and that nothing interferes with the throttle mechanisms on either throttle body. Turn the key on and allow the fuel system to pressurize. CHECK FOR ANY FUEL LEAKS and repair as necessary. Go to section 3 to verify power-up. Re-install any other bodywork removed. Seethe Techlusionwebsite for more detail.

HARLEY DAVIDSON AUTOMATIC COMPRESSION RELEASE TOOLS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-03-2011

download
INSTALLATION Compressed air can pierce the skin and flying debris from compressed air could cause serious eye injury. Wear safety glasses when working with compressed air. Never use your hand to check for air leaks or to determine air flow rates. (00061a) Wear safety glasses or goggles while drilling. Flying debris could result in serious eye injury. (00565b) 4 3 6 5 6 1 2 7 is05443 1. Drill, 1.250 inch 2. Drill stop collar, 1.250 inch 3. Drill stop gauge 4. Socket head screw, 5/16 inch 5. Socket head screw, 1/4 inch 6. Dowel pin 7. Top plate Figure 1. Top Plate and Drill Bit Stop Collar Installation 1. Remove valves from cylinder heads. NOTE Do not allow the threaded studs to damage the gasket sealing surface of the cylinder head. 2. See Figure 7 and Table 1. Mount a cylinder head to the tooling plate (1). 3. Place a head bolt spacer (7) over each stock head bolt and lubricate threads and thrust faces, dowels and studs. Tighten head bolts in a crisscross pattern to 10 ft-lbs (13.5 Nm) . 4. See Figure 1. Align the top plate (7) bolt and dowel holes with the head hole pattern, Screamin’ Eagle logo towards the spark plug. This plate will only fit one way for the cylinder head it is being installed on. If the plate does not align with the head, turn it over keeping the logo towards the spark plug and install the cylinder head. 5. Lubricate the two dowel pins (6) and insert in the top plate and into the cylinder head. 6. Apply lubricant to the two socket head screws (4 and 5). Insert into their respective holes in the plate to the cylinder head and tighten to 5 ft-lbs (6.8 Nm)

Kawasaki 900/1100 Billet Head Installation And REMOVAL Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1) Remove stock head and clean the top surface of the cylinder. 2) Remove the stock water fitting from the stock head and install it in the ADA Racing® billet head in the center cylinder location. Install the 1/8″ npt brass plugs in the 2 outer cylinder locations. 3) Install all o’rings in the ADA Racing® billet head, use small amounts of grease to hold them in place, do not use super glue or silicone. 4) Apply a small amount of grease to the small (OR020) o’ring at the top of the dome. This will allow the dome to easily slip into the head shell. Be careful when turning the head upside down to install onto the cylinder, as the domes can slide out of the head shell. 5) Make sure all the o’rings are in place and place the head on top of the cylinder with the water outlet on the intake side. You must be sure that none of the o’rings slip out of their groove, as this will cause an o’ring to get pinched and a water or compression leak could result. 7) Torque all of the nuts to 15ft/lbs, in a center-out criss-cross pattern. Now, torque them again to 18ft/lbs. 8) After the 1st time out riding the head should be re-torqued. 9) The 2 additional 1/8″ npt holes in the ADA Racing® billet head come with brass plugs, but barbed fittings can be installed for custom water routing applications.

Suzuki INTRUDER 1400 SLIP-ON EXHAUST SYSTEM Installation Manual

0

Filed Under (Suzuki) by admin on 22-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Loosenthe mounting bolt and pinch clamp on both left and right hand mufflers. 2. Loosenthe clamp on the crossover tube, located between the two mufflers. 3. Remove the two nuts that mount the front head pipe flange to the cylinder head. 4. Remove the two nuts that mount the rear head pipe flange to the cylinder head. 5. Remove the head pipes using a twisting motion to break the seal at the muffler and to clear the cylinder head. Note : If the exhaust coupler gaskets did not remain in the mufflers, remove them from the head pipes at this time. These coupler gaskets will not be reused in your new exhaust system. 6. Remove the mounting bolt from the left hand muffler. Remove the muffler, again using a twisting motion to seperate the crossover tube and set the muffler aside. (Save the stock mounting hardware for reuse). 7. Repeat step #6 on the the right hand muffler. Set the muffler aside. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Check the stock exhaust gaskets to be sure they are in good shape. If you have any doubts as to their condition, replace them. 2. Reinstall the stock head pipes to the engine. Note : Leave the flange nuts loose at this time. 3. Remove the mufflers from their boxes. There are a left and right hand muffler in this system. To define the difference between the left and right mufflers, check the bracket that is welded to the back side of the muffler. Each muffler is stamped with it’s own part number. Part # D500 is the RIGHT muffler and Part # D550 is the LEFTmuffler. 4. Install a three hole mounting bracket to each of the mufflers. Slide one dog bone shaped nut plate under the bracket that is welded to the backside of each muffler. Attach the mounting bracket using two of the 5/16 flange head bolts (supplied), leave them loose at this time. Note : Each muffler bracket has a number stamped on it, #179 bracket is for the left hand muffler and #180 is for the right hand muffler. When the brackets are mounted correctly, the end of the bracket with the single hole should point to the inlet end (small end) of the muffler. Refer to figure 1.

Incoming search terms: