andrews cams spec sheet

You search Auto repair manual PDF andrews cams spec sheet, if there are search results will appear below. If search results do not exist, please search by others keyword.



  andrews cams spec sheet Direct Download speed 5282 Kb/s

  andrews cams spec sheet Full Version speed 6162 Kb/s



HARLEY DAVIDSON VRSC BRACKET FOR BILLET HEADLAMP SHELL REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 31-01-2011

download
REMOVAL VRSCA Models 1. Remove windshield (if equipped). Refer to appropriate Instruction Sheet for procedures. 2. Remove right side cover and maxi-fuse. Refer to MAXI- FUSE in Service Manual. 3. See Figure 1. Disconnect headlamp connector (1) from vehicle wire harness. 4. Remove two screws (2), headlamp mounting bracket (3), and headlamp assembly (4) from upper bracket. 2 3 4 5 1 is03046 1. Connector 2. Screw (2) 3. Bracket 4. Headlamp assembly 5. Screw (2) Figure 1. VRSCA Headlamp Assembly VRSCB Models 1. Remove windshield (if equipped). Refer to appropriate Instruction Sheet for procedures. 2. Remove right side cover and maxi-fuse. Refer to MAXI- FUSE in Service Manual. 3. See Figure 2. Disconnect headlamp connector (1) from vehicle wire harness. 4. Remove two screws (2), headlamp assembly (3), and headlamp mounting bracket (4) from upper bracket. 5. Remove nut (5), screw (6), and trim ring (7) from head- lamp. 6. Remove lens assembly (8) from headlamp shell (9). Save lens assembly for Billet Headlamp Shell Kit 67704-03 installation INSTALLATION 2004-Earlier VRSCA and VRSCB Models 1. Assemble Chrome Billet Headlamp Shell Kit (67704-03). Refer to Instruction Sheet-J03018. NOTES VRSCA models use Headlamp 68297-05, while VRSCB models use original equipment lens assembly (including gasket and boot). Adapter ring from kit (Figure 6, Item 1) will be used to install billet headlamp assembly on Instruction Sheet-J03018. 2. See Figure 3. Cut the two connectors (1) from existing headlamp wire harness (2). Be sure to cut the wires as close to the back of the connector as possible. 3. See Figure 6. Route new wire harness (2) through the hole in bottom of the billet headlamp shell (A). NOTE Only one 16 AWG wire will fit into pin terminals included in kit. Both black wires (ground) can be joined together, then connected to a single wire, if desired. 4. Tape end of one black wire with electrical tape and secure it to wire harness. 5. See Figure 3 and Figure 6. Install terminal pin (3) and socket housing (4) onto new wire harness (Figure 6, Item 2). Refer to MULTILOCK ELECTRICAL CONNECTORS in Service Manual for installing socket/pin terminals. 3 4 1 2 is03025 1. Connector (2) 2. Wire harness 3. Terminal pin (4) 4. Socket housing Figure 3. 2004-Earlier VRSCA and VRSCB Headlamp Wire Harness 2005-Later VRSCA and VRSCB Models 1. Assemble Chrome Billet Headlamp Shell Kit (67704-03). Refer to Instruction Sheet-J03018. NOTES VRSCA models use Headlamp 68297-05, while VRSCB models use original equipment lens assembly (including gasket and boot). Adapter ring from kit (Figure 6, Item 1) will be used to install billet headlamp assembly on Instruction Sheet-J03018. 2. Disconnect and discard existing wire harness. 3. See Figure 6. Connect new wire harness (2) to billet headlamp shell (A). 4. Route wire harness (2) through hole in bottom of billet headlamp shell (A) before installing socket housing (4) provided in kit

Yamaha 2005 R1 Bike Tech Sheet

0

Filed Under (Yamaha) by admin on 18-01-2012

download
Engine: Type: Liquid cooled, four stroke, transverse four cylinder, DOHC, 5 valves per cylinder. Displacement: 1000cc Year: 2005 Horsepower: 180hp Clutch: PM Exhaust: Vance & Hines Race Exhaust Mufflers: Vance & Hines Frame: Type: Stock Year: 2005 Swing Arm: Performance Machine Chromoly +4 Extended Shocks: Race Tech Modifications: Race Tech Tuned and Lowered. Forks: Stock lowered 2.5″ Rim: Performance Machine Contrast Cut Torque Size: 19″ X 3.0″ Finish: Contrast Cut Fender: None Tire: Dunlop Sportmax D208ZR 120/70ZR19 Brake: Dual Performance Machine 4 piston Radial Calipers Wheels Rear: Rim: Performance Machine Contrast Cut Torque Size: 18″ X 8.5″ Brake: Performance Machine 4 piston Radial Caliper Finish: Contrast Cut Tire: Dunlop Elite3 250/40/R18 Other Parts: Handlebars: Stock Foot Controls: Over Racing Seat: Stock Turn Signals F/R: Anything Extra? Mirrors: Performance Machine Torque chrome Mirrors 19″ FRONT WHEEL! Paint, Chrome, and other F/X’s: Colors: yellow/Black Type: Special Paint: AirTrix Industries The Painter: Chris Wood Powder Coating: A to Z Coatings

Ultima Billet Rear Shocks Installation Instruction Sheet

0

Filed Under (Tips and Review) by admin on 30-11-2010

download
Unloading the rear suspension Use a jack under a flat part of the motorcycle and lift until the rear tire is barely resting on the surface. This ensures that the shocks are unloaded. They are now ready for removal. Remove the old shocks Refer to the service manual specific to your motorcycle for this process. Unbolt the old shocks. Save the necessary hardware if you have not purchased new hardware. Installation Shocks should be installed with the preload adjuster on top (see Preload Adjustment). With the new shocks in hand; please go over the hardware configuration diagram (Figure 3) to decide which configuration best fits your application. Spacers are included to provide clearance between the shocks and your motorcycle (Figure 4). Typically start on which ever side the final drive is located. This side normally causes the clearance issues. Each eye and each side should be configured the same way. Make sure to use the proper hardware so that the shock- bushings fit the shock-bolts as snugly as possible. Shocks come with a 1/2″ ID bushing installed. This is needed for all applications. An optional bushing is included and should be used in addition when 3/8″ bolts are used instead of the larger 1/2″bolts. Unless new hardware was purchased, you will use the stock bolts from your old shocks to install the new shocks. Use Red Locktite (or equivalent) and use a torque wrench to tighten as follows: Models that use 1/2″ bolts: 65ft-lbs Models that use 3/8″ bolts: 30ft-lbs (Figures 1 & 2) Be sure to check clearance between the shock and the belt-guard. If there is any contact you will need to alter your spacer arrangement to accommodate this. Check tire to fender clearance as well. This clearance will be reduced when lowering shocks are used. Preload Adjustment Your new Ultima Billet Shocks are preload adjustable. Adjustment should be done once the shocks are installed. To adjust use a strap wrench and turn the top part of the shock (Figure 6) clock-wise to tighten or provide more preload (this stiffens the suspension), or counter-clockwise to loosen or subtract preload (this softens the suspension). Hand adjustments may be sufficient on models with smaller spring rates while the strap wrench will be required on the high spring rate shocks. You will see notches (Figure 6) that appear on the shock as the shock is preloaded. These should help you obtain the same preload for both sides of the motorcycle. Both shocks should be adjusted to the same level of preload.

1999 YAMAHA YZF-R6 SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 25-11-2010

download
ENGINE SPECIFICATIONS/ELECTRICAL SPECIFICATIONS SPEC ENGINE SPECIFICATIONS Item Standard Limit Pistons Oil ring Dimensions (B T) End gap (installed) 1.5 2.0 mm 0.10 0.35 mm Crankshaft Crankshaft-journal-to-crankshaft- journal-bearing clearance 0.028 0.052 mm Carburetors ID mark Jet needle Pilot screw turns out 5EB1 #1, 4: N7RA #2, 3: N7SA 1-1/2 2 ELECTRICAL SPECIFICATIONS Item Standard Limit Ignition system Ignition timing 10 BTDC at 1300 r/min Ignition coils Primary coil resistance Secondary coil resistance 0.204 0.276 Ω 8.5 11.5 Ω Oil level switch model (manufacturer) 5EB (DENSO) Fuel pump relay model (manufacturer) Resistance G8R-30Y-M (OMRON) 162 198 Ω -3- TIGHTENING TORQUES SPEC CHASSIS TIGHTENING TORQUES Item Thread size Tightening torque Remarks Nm mkg Engine mounting adjusting bolts Rear shock absorber and frame Pivot shaft adjust bolt M10 7 40 5 0.7 4.0 0.5 -4- CABLE ROUTING SPEC 1 Throttle cables 2 Clutch cable 3 Left handlebar switch lead 4 Starter cable 5 Main switch lead 6 Front brake hose 7 Right handlebar switch lead AInstall the headlight relays onto the headlight housing bridge. BRoute the headlight lead through the plastic guide. CRoute the headlight lead through the headlight bracket right side, and connect relay. DDon’t kink. EPut coupler into stay. FMake sure the connector is out off the bottom end of front cowling. GRoute the right handlebar switch lead in front of the front fork inner tube. HRoute the throttle cables between the brake hose and right handlebar switch lead. IRoute the wire harness through under the left handlebar switch lead and starter cable. JFasten the left handlebar switch lead to the front fork with a plastic locking tie and cut the end of locking tie. KFasten the throttle cables and starter cable with a band. EB206000 CABLE ROUTING -5- CABLE ROUTING SPEC LLocate the end of band to for ward. Route the horn lead outside the throttle cables and fasten it to the under bracket with a plastic locking tie. Cut the end of locking tie. And then, route the horn lead under the brake hose and clamp it to the under cover

HARLEY DAVIDSON VRSC FUEL TANK SIDE COVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 05-02-2011

download
INSTALLATION 1. Note the left and right areas on frame where the covers will be installed. Using a 50/50 mixture of isopropyl alcohol and water, thoroughly clean the frame tubes surrounding the fuel cell on the left and right sides. Let dry completely. 2. Unlock and open seat. NOTE Loosening the ignition/light switch screw (in the following step) will allow much easier alignment of the ignition/light switch cover and ignition/light switch during installation. 3. See Figure 1. At area inside of frame rail just above the ignition/light switch housing, loosen the ignition/light switch screw just enough to allow the ignition/switch switch to move slightly from side to side and up and down. Do not completely remove screw 4. See Figure 4. Obtain the right side cover bracket (ignition/light switch side) from kit. 5. Remove the strips protecting the adhesive at all of the raised sections on the cover. 1 2 is 02045 1. Ignition/Light Switch Screw 2. Ignition/Light Switch Figure 1. Loosen Ignition Switch Assembly 6. See Figure 2. Carefully align the right side cover between the three frame tubes. Beginning with the left portion of the cover, press the cover between the upper and lower frame tubes until the raised portions of cover (with adhesive) begin to snap into place. While carefully aligning the right portion of the cover, move the ignition/light switch as necessary until centered within hole in cover, then firmly press into place. Adjust ignition/light switch until the switch is centered within cover. Make sure all raised locations (with adhesive) are firmly contacting the upper and lower frame tubes and that cushion rests against front vertical frame tube. 7. See Figure 1. Tighten the ignition switch screw to 6-10 Nm (53-88 in-lbs ) . NOTE The right side (ignition/light) switch cover surface can be damaged by the key fob (from vibration) when the key is in the ignition and the bike is running. You can either remove the key fob so it does not damage the cover surface, or you can install the plastic clear sheet (included in kit) onto the side cover for protection. 8. If desired, perform the following to install the plastic clear cover onto the ignition/light switch cover. a. Obtain the plastic (rhino) sheet and hold up to the switch cover to determine proper orientation and spacing. b. Carefully peel the adhesive backing from the plastic sheet and position onto the cover. Use a wet sponge, and working out from the center, rub out any bubbles or overlapped areas under the sheet. Allow to dry completely.

Tuning the HSR42/ 45 Carburetor

0

Filed Under (Tips and Review) by admin on 31-10-2010

download
your Mikuni HSR is fitted with the tuning parts we found to work with the great majority of engine performance modifications. However, the large number of differing exhaust systems and cams available makes it impossible to accommodate all possible combinations with one carburetor set-up. Your HSR will almost certainly run correctly on your engine without exchanging any parts. But, if it doesn’t, you may alter its tuning to suit your engine’s needs by following this guide. Some exhaust system designs strongly interfere with carburetor tuning. For instance, it is very difficult to get smooth and responsive carburetion through the entire rpm range with straight pipes and completely open exhausts. In addition, very small volume, small diameter mufflers are often ‘seen’ by the engine as straight pipes and present the same tuning difficulties. Very long duration cams often cause relatively poor running below about 3,000 rpm, depending upon the individual cam’s intake valve closing point. Such cams cause reverse airflow out the mouth of the carburetor (often called “reversion” or “standoff”) that can be mistaken for a carburetor tuning problem. Harley-Davidson Screamin’ Eagle performance parts are proven and predictable. If you have any doubts about a particular exhaust system, air cleaner or ignition, you may substitute the Harley Screamin’ Eagle parts as a “reality check.” When re-tuning is required, it usually involves small alterations to the idle and/or main system. The following pages supply enough information to make such alterations relatively simple. Please note that there is no point in attempting to tune any carburetor unless the engine is sound and in a good state of tune. If you have any doubts about the general condition of your engine, have it checked by your dealer or an experienced mechanic before attempting to fine-tune your Mikuni.

Incoming search terms:

HARLEY DAVIDSON HYBRID CAM PLATE AND HIGH FLOW OIL PUMP KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the service manual and follow the instructions to remove the seat and disconnect the battery cables, negative (-) cable first. Retain all seat mounting hardware. Gasoline can drain from the carburetor fuel line when disconnected from fuel valve fitting. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. Wipe up spilled fuel immediately and dispose of rags in a suitable manner. (00256a) NOTES Installing this kit requires removal and installation of the cam support plate. Refer to the service manual for instructions with the following exception pertaining to cam compartment compo- nents: The crank and primary cam sprocket flange bolts are specially hardened, and the flat washers are of a special diameter and have ground surfaces. Use ONLY the parts provided in the Drive Gear Retention Kit (H-D Part Number 25533-99A, sold separately) when installing this kit. -J04804 1 of 7
The cr ank sprocket flange bolts and pr imary cam sproc ket flange bolts ARE NOT interchangeable. 2. Refer to the service manual to remove and discard the crank sprocket flange bolts and primary cam sprocket flange bolts and washers. 3. For 1999 models only: Refer to the service manual to remove and discard the currently installed cam drive sprocket. 4. Refer to the service manual to remove and disassemble the cams from the support plate and oil pump. Discard the support plate and oil pump. 5. For 1999 – 2000 Dyna, 2000 Softail, 1999 – 2000 Touring, and 2001 EFI Touring models only: Inspect the cams, chain, sprockets and chain tensioners for wear, and replace as needed. Refer to the service manual for inspection and replacement procedures. For 2001 – 2005 Dyna, 2001 – 2006 Softail, 2002 – 2006 Touring, and 2001 carbureted Touring models only: Inspect the cams and secondary cam chain for wear, and replace as needed. Refer to the service manual for inspection and replacement procedures. The primary cam chain, primary sprockets and both tensioners will be replaced by new components from the kit. For ALL models and years: Discard the guide, as it will not be used. INSTALLATION 1. ALL models: See Figure 1. Obtain the new Rear Cam Roller Bearing Kit (H-D Part Number 8983) from inside the Cam Service Kit (H-D Part Number 17045-99C, purchased separately), and install as indicated in Step 2. NOTE See Figure 2. If not enough of the splined shaft is exposed to install the sprocket, omit the spacer (4) and proceed to Step 2e. When the bearing inner race is started onto the machined area, remove the flange bolt (5), flat washer (6) and sprocket, then assemble using the spacer (4). Repeat Step 2e to fully install bearing inner race. To center thrust washer, be sure o-ring is installed in relief groove. Damage to bearing cage and engine can occur if thrust washer is not centered. (00473b) 2. See Figure 1. Install the O-ring (5), thrust washer (4) and bearing inner race (3) onto the rear camshaft as follows: a. See Figure 2. To properly locate the thrust washer (2), install the O-ring (3) in the grinding relief groove on the splined end of the rear camshaft between the machined area and the secondary cam sprocket.

Incoming search terms:

HARLEY DAVIDSON SCREAMIN' EAGLE BILLET CAM SUPPORT PLATE REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2011

download
REMOVAL NOTE For removal, refer to the appropriate sections of the applicable Service Manual for detailed information on the following generalized steps. To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Remove the Maxi® fuse. 2. Remove the cam cover and gasket. 3. Remove and discard the crank and primary cam sprocket flange bolts and washers. 4. Release the oil pump, and remove the cam support plate and cams. Disassemble the cams from the support plate and discard the support plate. 5. Inspect cams, chain, sprockets, oil pump, chain tensioners and guide for wear and replace as needed. Refer to the Service Manual for inspection and replacement proce- dures. -J04503 INSTALLATION NOTES For installation, refer to the appropriate sections of the applicable Service Manual for detailed information on the following generalized steps. See Figure 1. When installing Screamin’ Eagle camshaft kits, install the O-ring included in this kit over the splined shaft of the rear camshaft as shown. 1. Using the Camshaft Assembly Tool (HD-47956) and assemble the camshafts, chains and tensioners to the billet cam support plate. 2. Install the cam support plate assembly into the crankcase. 3. Using the Crankshaft/Camshaft Locking Tool (HD-47941), install cam sprockets, chain and tensioner. 4. Install cam cover and gasket. 5. Install Maxi fuse.

HARLEY DAVIDSON CHROME BILLET LIFTER-COVER KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-02-2011

download
Installation with Stock Pushrods Refer to the service manual for your motorcycle model. Installation with Adjustable Pushrods Lifter-Cover Removal Installing or removing the pushrods with the valve train loaded can result in engine damage. On the cylinder being serviced, always set the lifters to the base circle on the cam before servicing pushrods, lifters, rocker arms, and valves. 1. Set the lifters of the rear cylinder to their lowest point, or base circle, on the cam. Refer to Setting the Lifters to the Base Circle in this instruction sheet. 2. See Figure 1. Insert a screwdriver into the slot on the side of the spring-cap retainer on the pushrod cover. 3. Press the spring-cap and retainer down while pulling outward to remove the spring-cap retainer. 4. See Figure 2. Lift the lower pushrod cover to reveal the lower third of the pushrod. 5. If the engine has stock pushrods installed and you are installing adjustable pushrods with this lifter-cover installation, go to step 6. If the engine already has adjustable pushrods installed and you are installing adjustable pushrods with this lifter-cover installation, go to step 7 6. Use a bolt cutter or similar tool to cut the stock pushrod. Avoid cutting the pushrods with a saw, grinder, or other method that may allow metal debris into the engine. Go to step 8. 7. Loosen the jam nut on each adjustable pushrod and resize each rod to its shortest length. 8. Remove the pushrod covers and pushrods from the engine. 9. Remove the O-rings from the seats in the engine at the top and bottom of the pushrod cover. 10. Remove the four screws fastening the lifter cover to the engine to remove the cover and gasket. 11. Remove old lifter-cover gasket material from the engine, taking care not to allow material to fall into the engine. Continue to Lifter-Cover Installation in this I-Sheet. Lifter-Cover Installation 1. See Figure 3. Verify that the lifter anti-rotation pin is in position. Installing or removing the pushrods with the valve train loaded can result in engine damage. On the cylinder being serviced, always set the lifters to the base circle on the cam before servicing pushrods, lifters, rocker arms, and valves. 2. Verify that the cylinder lifters are set to their lowest point, or base circle, on the cam. Refer to Setting the Lifters to the Base Circle in this instruction sheet. 3. Fasten the new lifter-cover gasket and chrome billet lifter cover to the engine using the chrome screws from this kit. In a cross pattern, torque the lifter-cover screws to 90 – 120 in-lbs (10.2 – 13.6 Nm). 4. See Figure 4. Loosen the jam nut on all of the pushrods and adjust the pushrods to their shortest length. NOTE See Figures 4 and 5. Install the narrow-band pushrods in the cylinder-intake location. Install the wide-band pushrods in the cylinder-exhaust location. 5. Assemble the O-rings (purchased separately) and pushrod covers. 6. Install the pushrods with the pushrod covers. The adjustment-end of the pushrod must be on the lifter

Incoming search terms:

HARLEY DAVIDSON DIAMONDBACK "LE" CHROME SERIES CLUTCH CABLE KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
CLUTCH CABLE REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the battery or main fuse following the instructions in the appropriate Service manual. 2. When performing cable disassembly procedures, make careful notes as to the existing cable routing and existing cable strap locations. New straps can be installed in the same locations. 3. Remove the clutch cable following the instructions in the appropriate Service Manual. 4. If installing different handlebars, install them now (refer to the appropriate handlebar instruction sheet) and measure the change in distance that will be required from the end of the cable housing to the clutch lever. Install proper length clutch cables. Incorrect cable length can adversely affect motorcycle operation, which could cause loss of control resulting in death or serious injury. (00448b) 5. Compare the additional required length to the cable provided in your kit. If the cable is more than two inches (50.8 mm) longer or more than one inch (25.4 mm) shorter than the above measured distance, see a Harley-Davidson dealer for the correct cable length. CLUTCH CABLE INSTALLATION Sportster and Softail Models Do not over-tighten clutch cable threaded end fitting. Use recommended torque values. Damage to threaded fitting can lead to loss of transmission fluid, which could result in loss of control and death or serious injury. (00449c) -J04568
NOTE Damage to the clutch cable threaded end fitting due to improper handling/installation is not covered under the Harley-Davidson Motor Company Warranty. 1. See Figure 11. Apply a light coat of clean engine oil on the new O-ring (2) before installing the O-ring onto the threaded portion of the clutch cable end. 2. Install the clutch cable following the instructions in the appropriate Service Manual EXCEPT: Tighten clutch cable fitting to clutch release cover to 36-60 in-lbs (4-7 Nm) . Replace anchor pin with anchor pin supplied in this kit, see Figure 11, item (1 or 7). 3. After installation, follow the instructions in the “Final Assembly” and “Clutch Cable Adjustment” sections in this instruction sheet. FLTR Models with Fairing Lowers 1. See Figure 1. Carefully twist the clutch cable around the coiled opening in the clutch cable guide (2) with the eyelet toward the left handlebar. 2. Route the clutch cable assembly down from the clutch cable clamp while crossing to the right side of the vehicle. Run the cable between the inboard side of the right frame downtube and the outboard side of the voltage regulator. 3. The clutch cable clamp, mounted on the engine guard, has two fingers, an upper and a lower. Feed the cable assembly under one finger and over the other. 4. Finish the installation of the clutch cable following the instructions in the appropriate Service Manual EXCEPT: Tighten clutch cable fitting to clutch release cover to 36-60 in-lbs (4-7 Nm) . Replace anchor pin with anchor pin supplied in this kit, see Figure 11, item (1 or 7). NOTE See Figure 2. Adjust the clutch cable clamp to 2.25 ± 0.25 in. (57.15 ± 6.35 mm) as measured from the inside lower left fairing mount to the clutch cable clamp. 5. After installation, follow the instructions in the “Final Assembly” and “Clutch Cable Adjustment” sections in this instruction sheet.

Incoming search terms: