2011 ktm 250 xc standard carburettor settings

You search Auto repair manual PDF 2011 ktm 250 xc standard carburettor settings, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2011 ktm 250 xc standard carburettor settings Direct Download speed 5282 Kb/s

  2011 ktm 250 xc standard carburettor settings Full Version speed 6162 Kb/s



2008 KTM 250 SX-F 250 XC-F, XCF-W 250 EXC-F, EXC-F SIX DAYS INSTALLATION MANUAL

0

Filed Under (KTM) by admin on 22-10-2010

download
Hand brake lever The hand brake lever [1] is mounted on the handlebars on the right and actuates the front wheel brake. The adjusting screw [A] can be used to change the basic position of the hand brake lever (see “Maintenance”). 1 A Short circuit button The short circuit button [2] turns off the engine. When pressing this button, the ignition circuit is short-circuited. 2 Headlamp switch (XCF-W) In this model the headlamp is switched on with the pull switch [5] . 5 Flasher switch The flasher switch is a separate unit and is mounted on the left portion of the handlebar. The wire harness is designed in a way that whenever you want to use your bike off-road, you can dismount the entire turn indicator system without affecting the function of the remaining electrical system. Flasher left Flasher right
OPERATION INSTRUMENTS » ENGLISH 7 1 2 3 4 5 Starter button Pushing the red starter button [1] will actuate the E-starter. Emergency OFF switch (EXC-F Australia) The red emergency-OFF switch [2] is arranged adjacent to the throttle grip. In this position, the E-starter is operational and the engine can be started. In this position, the E-starter and ignition circuits are interrupted.The E-starter cannot be actuated, and the engine will not start, not even if you attempt to start it with the kickstarter. Pushing the black starter button [3] will actuate the E-starter. Indicator lamps The green control lamp [4] flashes in the same rhythm as the flashing indicator when the indicator is working. The blue control lamp [5] lights up when the high beam is on. TEST All of the display segments briefly light up for the display function test. Electronic speedometer The display in the electronic speedometer is activated as soon as you press a button on the speedometer or an impulse is received from the wheel sensor. The display lights up when the engine is running. The display is cleared if no button is pressed for 1 minute or no impulse is received from the wheel sensor. The button is used to change between display modes. The + and – buttons are used to control various functions

Incoming search terms:

Kawasaki Ninja 250 FAQ

0

Filed Under (Kawasaki) by admin on 15-11-2010

download
Am I too small for this motorcycle? Duke – Sun May 14 17:38:31 2000 I’m only about 5’2″ and don’t have a problem, even though I can only touch the ground with the ends of my toes. Once you get a feel for the balance of the bike it’s not hard to keep everything upright. Only place I have trouble is pushing the bike backwards in a parking lot. Usually I just walk the bike (beside it) to where I can get on and get going. How does the EX500 compare to the EX250? Craig M. – Mon May 22 10:23:29 2000 I have both the EX250 and the EX500; both are Y2K models. The 250 is a screamer that performs well and can easily get me into trouble. My only complaints about the 250 are the excessive nose dive when getting on the front brake hard and the skittishness of the rear during high speed cornering. Both are easily corrected with suspension adjustments, I’ve just been too lazy to get the parts and do the work. A bit more wind protection would be great too. The 500 addresses these problems, the diving of the front end (to a degree); the rear’s skittishness and the wind protection. A plus for the 500 is the greater torque and power off the line; it pulls stronger (in my opinion) and will get you into illegal speed territory just a bit quicker than the 250. With greater weight, is has more stability in high speed and windy situations. Insurance is just about the same for both, with the 250 getting the nod for gas mileage. Service requirements are almost identical for both as well, being that they’re both parallel twins, the technology is the virtually the same. The downfalls of the 500: $2K more than the 250 (can do a lot to the 250 with that kind of money); buzzy mirrors, barely useful; heavier weight to have to push around the garage; lesser gas mileage (55-60 MPG; 250 pushes 70 MPG easily); engine is worse than a nervous dog shaking around at idle and at speed (here the 250 is far superior and much smoother). In my opinion, the 500 is a better suited for a larger rider, from a comfort standpoint. I feel I can stretch out a bit more on it than the 250 (I’m 5′ 9″, 160 lbs). The 250′s brakes are better tuned than the 500 and the shifter is much smoother. That may be due to the 3,500 mile difference between the two bikes. Bottom line, both bikes are great, the 250 is now my wife’s ride (mainly) and the 500′s mine (unless she steals the keys away). In time, I’ll make the adjustments to the 250; she doesn’t push it like I do.

Incoming search terms:

2006 KTM 250 SX-F 250 EXC RACING 400 EXC RACING 450 SX, XC, EXC RACING 525 SX, XC, EXC RACING, REPAIR MANUAL

0

Filed Under (KTM) by admin on 05-05-2012

download
Hot start lever (250 SX-F) If you pull the red hot start lever [1] during the starting procedure backward, a bore in the carburetor will be opened through which the engine may take in additional air. The result is a „lean” fuel-air mixture of the type needed for hot starts.
ENGLISH 7 OPERATION INSTRUMENTS » Headlamp switch (EXCUSA) In this model the headlamp is switched on with the pull switch [1] . Flasher switch The flasher switch is a separate unit and is mounted on the left portion of the handlebar. The wire harness is designed in a way that whenever you want to use your bike off-road, you can dismount the entire turn indicator system without affecting the function of the remaining electrical system. Flasher left Flasher right Starter button (EXC) Pushing the black starter button [2] will actuate the E-starter. Emergency OFF switch (EXC Australia) The red emergency-OFF switch [3] is arranged adjacent to the throttle grip. In this position, the E-starter is operational and the engine can be started. In this position, the E-starter and ignition circuits are interrupted.The E-starter cannot be actuated, and the engine will not start, not even if you attempt to start it with the kickstarter. Pushing the black starter button [4] will actuate the E-starter. 2 3 4 5 6 Indicator lamps The green control lamp [5] flashes in the same rhythm as the flashing indicator when the indicator is working. The blue control lamp [6] lights up when the high beam is on

Incoming search terms:

KTM 125 EXC, EXC SIXDAYS 200 XC, XC-W, EXC 250 XC, XC-W, EXC, EXCSIXDAYS 300 XC, XC-W, EXC-E, EXC-ESIXDAYS OWNER'S MANUAL 2008

0

Filed Under (KTM) by admin on 02-12-2010

download
Chassis number The chassis number is stamped on the right side of the steering head tube. Enter this number in the field on page no 1. Engine number, engine type The engine number and the engine type are stamped into the left side of the engine below the engine sprocket. Enter this number on page 1. Clutch lever The clutch lever [1] is located on the left side of the handlebars. The adjusting screw [A] is used to change the original position of the clutch lever (see maintenance work on chassis and engine). The clutch is hydraulically actuated and adjusts itself automatically. Hand brake lever The hand brake lever [2] is mounted on the handlebars on the right and actuates the front wheel brake. The adjusting screw [B] can be used to change the basic position of the hand brake lever (see maintenance work on chassis and engine). OPERATION INSTRUMENTS » 1 2 A B
ENGLISH 6 OPERATION INSTRUMENTS » TEST All of the display segments briefly light up for the display function test. WS (wheel size) The display changes and the circumference of the front wheel is briefly displayed in millimeters (2205 mm corresponds to a front wheel circumference of 21″ with production tires). Afterwards the display will return to the previous display mode. Electronic speedometer The display in the electronic speedometer is activated as soon as you press a button on the speedometer or an impulse is received from the wheel sensor. The display lights up when the engine is running. The display is cleared if no button is pressed for 1 minute or no impulse is received from the wheel sensor. The button is used to change between display modes. The + and – buttons are used to control various functions. SPEED display mode / H (service hours) Only the SPEED / H and SPEED / ODO display modes are activated in the condition at delivery. SPEED/H is displayed whenever the display is activated and the front wheel is not turning. It automatically changes to the SPEED/ODO display mode as soon as the front wheel starts turning. SPEED displays the speed. H displays the engine’s service hours. The service hour counter starts to count as soon as you start the engine. The displayed figure cannot be changed. Service intervals are indicated in service hours for some KTM offroad motorcycles, making the service hour counter a very practical function. SPEED / ODO display mode (odometer) The SPEED/ODO mode displays the speed and the total distance traveled. The display automatically changes to the SPEED/H display mode when the front wheel stops turning. + button no function – button no function briefly press buttonchanges to the next display mode hold button 3 secs. changes to the next display mode The electronic speedometer has a number of display modes (functions) that you can also activate (reveal) (see: Activating and deactivating display modes).
ENGLISH 7 OPERATION INSTRUMENTS » SPEED / LAP (lap time) display mode You can use the manual stop watch to stop and store up to 10 lap times, which you can view in the LAP/LAP display mode (see below). LAP displays the lap times in hours, minutes and seconds. + button Starts and stops the stop watch, lap time is not reset to 0 – button Stops the stop watch, stores the lap time and restarts the stop watch again. The time is reset to 0. A total of 10 lap times can be stored. If the lap time continues to run after you press the – button, all 10 memory locations are occupied.To clear all of the stored lap times, hold the button for 3 seconds in the SPEED/LAP mode.Up to 10 lap times can be stored in this way. briefly press buttonChanges to the next display mode.If no lap time is stored or the motorcycle is driving, the LAP/LAP mode will be skipped. hold button 3 secs. Clears all LAP figures SPEED / CLK (time) display mode CLK displays the time in hours, minutes and seconds. + button no function – button no function briefly press buttonchanges to the next display mode hold button 3 secs. set the clock menu To set the clock, see „Setting the clock”. Activating and deactivating display modes In the display mode SPEED/H, press and hold the button for 3 seconds to access the SETUP menu. The active functions will be displayed. The blinking function can be activated by pressing the + button and deactivated by pressing the – button. Press and hold the button 3 seconds to store the settings. If no button is pressed for 20 seconds, the setting will be stored automatically and the display will return to the SPEED/H mode. + button activates the blinking display – button deactivates the blinking display briefly press buttonchanges to the next display without changing any settings hold button 3 secs. starts the SETUP stores the settings and changes to the SPEED/H mode

Incoming search terms:

2004 KTM 250 EXC-R exhaust system INSTALLATION

0

Filed Under (KTM) by admin on 07-02-2012

download
1. Remove the rear shock and the standard exhaust pipe. And attach the rear shock again. (Standard exhaust flange should remain the current position) 2. Lightly attach the front exhaust pipe to the engine. (See Photo. 2) 3. Insert the joint and tail pipe to lightly attached front exhaust pipe in step 2. Shake the whole for the better fitting. Then, attach the supplied springs to the joint. Lightly attach this tail pipe with the standard bolt. *Insert the two inner collars to the joint. 4. Lightly assemble the silencer and the silencer stay. Insert this to the tail pipe. Lightly attach this tail pipe to the standard attachment position with supplied bolt and collar. Check the best position for the silencer band. (See Photo. 3) 5. Remove the silencer attached in step 4. Securely fasten the bolt of the silencer band. Insert this silencer to the tail pipe and lightly fasten the bolt of the stay. 6. Securely attach the tail pie followed by the silencer stay. 7. Attach supplied springs to the joint of the silencer. 8. Clean all surfaces. Remove any oil on the exhaust pipe and silencer. 9. Make sure all bolts and nuts are securely fastened. Run the engine and ensure there are no exhaust gas leaks. (See Photo. 4) *Carburetor adjustment will be required in the weather and course

KTM ATV 525 XC specification

0

Filed Under (KTM) by admin on 12-11-2010

download
Engine ] Pure power for Enduro enthusiasts. The power of the 525 XC is the indisputable benchmark in the ATV Enduro sector. Its acceleration and top speed cast a shadow over all its predecessors. Variable ignition curves and perfect maintenance features like simple valve play adjustment and the removable clutch cover are even further highlights of the XC engine that make the KTM Enduro quads so superior. First Oil Filling for all KTM Engines. [ CarburEttor ] The Keihin carburettor, which has been proven multiple times in racing, with 39 mm and the Throttle Positioning System guarantees a uniform, forceful power delivery in all speed ranges. It ensures an unrivalled response behavior and perfect service-friendliness at all times. [ StartEr ] Packed in a space-saving manner into the free space behind the cylinder head, the small, light electric starter motor is ready for use. It brings every KTM ATV up to speed reliably and comfortably even when racing becomes hectic. [ rEar SuSPENSIoN ] Premium-quality ÖHLINS suspension components specially designed for tough Enduro use are provided as standard – both at the front and the rear. Easy to adjust, they guarantee optimal tuning for the most varied of terrains. Another highlight: the front and rear spring travel of 275 mm and 272 mm respectively is 100 % trend-setting for an Enduro ATV! [ alumINIum SubFramE ] The rear subframe is made of aluminium and is extremely light and easy to remove. [ FramE ] The lightweight, extremely durable frame sets the benchmark in the quad racing segment and is made of high-strength, powder-coated Chromoly steel. [ haNDlEbar ] An ultra-durable tapered aluminium Magura® handlebar comes standard that is four-position adjustable to suit your preferred ergonomics. Further highlights are the functional and individually adjustable operating levers for brake and hydraulic clutch. In addition, the chassis has an integrated mount for a steering damper – available as a PowerPart accessory. [ CurvED raDIator ] Best cooling by means of its curved shape and the resulting maximized surface area. [ rImS / tIrES ] MAXXIS Razr tyres on light, stable DWT aluminium rims. [ ExhauSt ] The powerful XC silencer is made of light-weight aluminium.

KTM 250-525 SX, MXC, EXC RACING ENGINE REPAIR MANUAL

0

Filed Under (KTM) by admin on 07-02-2012

download
TM REPAIR MANUAL IN LOOSE-LEAF FORM STORING THE REPAIR MANUAL IN THE BINDER -Put the index into the binder. -Put the front page of the repair manual (210×297 mm) into the transparent pocket provided for this purpose on the outside of the binder. -Put the spine label (170×45 mm) into the transparent pocket provided for this purpose on the spine of the binder. -Put the summary list of contents (150×297 mm) into the transparent pocket provided for this purpose on the inside of the binder or insert this page on the beginning of the manual. -Then insert the individual chapters of the manual between the sheets of the index according to the page number printed in the right bottom corner of each page. Example: page no. 3-5 3 = chapter 3 5 = page 5 All pages with a page number that begins with the digit 3, for example, must be put under the index heading „Chapter 3″. -Index sheets that have not been marked with a certain chapter are for your personal convenience. T he respective headings can be entered in the list of contents. Remove page (s) Replace by page (s) Insert page (s) after page 2-1 / 2-7 2-1C 2-7C to 2-9C 3-1 3-1C 4-1 to 4-14 4-1C to 4-13C 5-1 / 5-3 5-1C / 5-3C 5-6 to 5-8 5-6C to 5-8C 5-12 to 5-26 5-12C to 5-27C 6-1 / 6-4 6-1C / 6-4C 6-7 to 6-16 6-7C to 6-17C 7-1 to 7-2 7-1C to 7-2C 7-7 to 7-11 7-7C to 7-11C 8-1 to 8-13 8-1C to 8-21C 9-1 9-1C 9-10 to 9-13 9-10C to 9-16C 10-1 10-1C 10-8C to 10-11C 11-1 11-1C 11-11C to 11-13C
Repair manual KTM 250-525 SX, MXC, EXC RACING Art.-No. 3206007 -E EXPLANATION – UPDATING Edition 01/2003 3.205.85-ERepair Manual 400/520 SX, MXC, EXC RACING Basic version Model year 2000 (Engine number with first digit “0″) 2/2000 3.210.01-EUpdating of Rep.Manual 3.205.85-E Model year 2001 (Engine number with first digit “1″) 1/2001 3.210.44-EUpdating of Rep.Manual 3.205.85-E Model year 2002 (Engine number with first digit “2″)

KTM 250/ 300/ 380 SX,MXC,EXC ENGINE REPAIR MANUAL

0

Filed Under (KTM) by admin on 12-11-2010

download
Repair manual KTM 250 / 300 / 380 Art No 3206004 -E 2-2C main jet jet needle jet needle air control screw idle adjusting screw idle jet throttle valve Idling range A Operation with closed throttle valve. This range is influenced by the position of the air control screw 1 and the idle adjusting screw 2 . Only make adjustments when the engine is hot. To this end, slightly increase the idling speed of the engine by means of the idle adjusting screw. Turning it clockwise produces a higher idling speed and turning the screw counterclockwise produces a lower idling speed. Create a round and stable engine speed using the air control screw (basic position of the air control screw = open by 1.5 turns). Then adjust to the normal idling speed by means of the idle adjusting screw. Opening up B Engine behavior when the throttle opens. The idle jet and the shape of the throttle valve influences this range. If, despite good idling-speed and part-throttle setting, the engine sputters and smokes when the throttle is fully opened and develops its full power not smoothly but suddenly at high engine speeds, the mixture to the carburetor will be too rich, the fuel level too high or the float needle is leaking. Part-throttle range C Operation with partly open throttle valve. This range is only influenced by the jet needle (shape and position). The optimum part-throttle setting is controlled by the idling setting in the lower range and by the main jet in the upper range. If the engine runs on a four-stroke cycle or with reduced power when it is accelerated with the throttle partly open, the jet needle must be lowered by one notch. If then the engine pings, especially when accelerating under full power at maximum engine revs, the jet needle should be raised. If these faults should occur at the lower end of the part throttle range at a four-stroke running, make the idling range leaner; if the engine pings, adjust the idling range richer. Full throttle range D Operation with the throttle fully open (flat out). This range is influenced by the main jet and the jet needle. If the porcelain of the new spark plug is found to have a very bright or white coating or if the engine rings, after a short distance of riding flat out, a larger main jet is required. If the porcelain is dark brown or black with soot the main jet must be replaced by a smaller one. mixture too rich: too much fuel in proportion to air mixture too lean: not enough fuel in proportion to air 1 2 OPERATING RANGES OF THE CARBURETOR 2-3C Carburetor adjustment Basic information on the original carburetor setting The original carburetor setting was adapted for an altitude of approx. 500 meters (1600 ft.) above sea level, and the ambient temperature of approx. 20°C (68°F), mainly for off-road use and central European premium-grade fuel (ROZ 95 MOZ). Mixing ratio 2-stroke motor oil : super fuel 1:40 – 1:60. Basic information on a change of the carburetor setting Always start out from the original carburetor setting. Essential requirements are a clean air filter system, air-tight exhaust system and an intact carburetor. Experience has shown that adjusting the main jet, the idling jet and the jet needle is sufficient and that changes of other parts of the carburetor will not greatly affect engine performance. RULE OF THUMB:

Incoming search terms:

KYMCO MAXXER 300/ 250 MONGOOSE 300/ 250 SERVICE MANUAL

0

Filed Under (Kymco) by admin on 26-10-2010

download
apply or add designated greases and lubricants to the specified lubrication points. ÑAfter reassembly, check all parts for proper tightening and operation. ÑWhen two persons work together, pay attention to the mutual working safety. ÑDisconnect the battery negative (-) terminal before operation. ÑWhen using a spanner or other tools, make sure not to damage the motorcycle surface. ÑAfter operation, check all connecting points, fasteners, and lines for proper connection and installation. ÑWhen connecting the battery, the positive (+) terminal must be connected first. ÑAfter connection, apply grease to the battery terminals. ÑTerminal caps shall be installed securely. 1 . GENERAL INFORMATION 1-6 ATV 300/250 ÑIf the fuse is burned out, find the cause and repair it. Replace it with a new one according to the specified capacity. ÑAfter operation, terminal caps shall be installed securely. ÑWhen taking out the connector, the lock on the connector shall be released before operation. ÑHold the connector body when connecting or disconnecting it. ÑDo not pull the connector wire. ÑCheck if any connector terminal is bending, protruding or loose. Confirm Capacity 1 . GENERAL INFORMATION 1-7 ATV 300/250 ÑThe connector shall be inserted completely. ÑIf the double connector has a lock, lock it at the correct position. ÑCheck if there is any loose wire

KTM 125/ 200/ 250/ 300 SX, MXC, EXC SERVICE MANUAL

0

Filed Under (KTM) by admin on 28-11-2010

download
Compression damping of shock absorber (MXC, EXC) The compression damping (during compression) can be adjusted for the MXC and EXC shock absorbers (Mono Compression Control). The degree of damping can be adjusted by turning adjusting screw 1 with a screwdriver. Turning in a clockwise direction will increase the damping, turning in a counterclockwise direction will decrease the damping. STANDARD ADJUSTMENT: -Turn the adjusting screw clockwise to the stop. -Then turn the adjusting screw counterclockwise, counting the number of clicks that corresponds to the respective type of shock absorber. Type White Power 1218X757…………..17 clicks Type White Power 1218X759…………..17 clicks * WARNING * THE DAMPING UNIT OF THE SHOCK ABSORBER IS FILLED WITH HIGH – COMPRESSION NITROGEN . NEVER TRY TO TAKE THE SHOCK ABSORBER APART OR TO DO ANY MAINTEN – ANCE WORK YOURSELF . SEVERE INJURIES COULD BE THE RESULT . NEVER UNSCREW THE BLACK SCREW 2 CONNECTION (24 MM ). Rebound damping of shock absorber (SX, MXC, EXC) By using the adjusting screw 3 , the degree of damping of the rebound can be adjusted. Turn the knob to the right side to increase damping, turn it to the left side to reduce damping during rebounding. STANDARD ADJUSTMENT: -Turn the adjusting screw clockwise to the stop. -Then turn the adjusting screw counterclockwise, counting the number of clicks that corresponds to the respective type of shock absorber. Type White Power 1218X756…………..28 clicks Type White Power 1218X757…………..28 clicks Type White Power 1218X759…………..26 clicks * WARNING * THE DAMPING UNIT OF THE SHOCK ABSORBER IS FILLED WITH HIGH – COMPRESSION NITROGEN . N EVERTRYTOTAKETHESHOCKABSORBERAPARTORTODOANYMAINTE – NANCE WORK YOURSELF . SEVERE INJURIES COULD BE THE RESULT . NEVER UNSCREW THE BLACK SCREW 4 CONNECTION (15 MM )

Incoming search terms: