1998 road king starter removel

You search Auto repair manual PDF 1998 road king starter removel, if there are search results will appear below. If search results do not exist, please search by others keyword.



  1998 road king starter removel Direct Download speed 5282 Kb/s

  1998 road king starter removel Full Version speed 6162 Kb/s



HARLEY DAVIDSON ROAD KING SOLO BUCKET AND PASSENGER PILLION INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
Installation SOLO SADDLE ONLY 1. Remove stock seat and grabstrap according to applicable Service Manual instructions. 2. Road King standard models . Remove and save the stock screws and seat mount bracket at the back of the rider solo seat. 2000 and later models . Remove the retainer washer from the stud plate and replace with two black retainer washers (2). Be careful not to allow stud plate to fall through the fender. 3. Road King standard models . Install stock solo seat mount bracket using two stock screws saved in Step 2. Road King Classic Custom models . Install solo seat mount bracket onto back of solo seat using bracket and screws included in Mount Kit Number 52903-01. 4. Install seat by sliding front of seat into seat holder bracket. Pull up on the nose of the seat to verify that the seat is securely installed. After installing seat, pull upward on front of seat to be sure it is in locked position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070a) 5. 1999 and later models . Install 1/4 in. star washers (6), spacers (4) and acorn nuts (3) onto rear mount studs. Torque to 72 in-lbs (8.13 Nm). 1998 and earlier models . Install 5/16 in. star washers (5) and 5/16-18 x 3/4 in. buttonhead screws (1) into stock mount nuts. Torque to 17 ft-lbs (23 Nm). SOLOAND PILLION 1. Remove stock seat and grabstrap according to applicable Service Manual instructions. Retain all hardware for later use. 2. Road King standard models . Remove and save the stock screws and seat mount bracket at the back of the rider seat. 3. Road King standard models. Install stock seat mount bracket onto new solo seat using two screws saved in Step 2. Road King Classic Custom models. Install solo seat mount bracket onto back of solo seat using bracket and screws included in Mount Kit Number 52903-01. 4. 1999 and later Road King standard models . Secure the rear mount bracket with stock mushroom nuts (10) and two 1/4 in. star washers (6). Torque to 72 in-lbs (8.13 Nm). 1998 and earlier Road King standard models . Install solo seat by sliding front of seat into holder bracket on bike. Secure the rear mount bracket with the two mushroom screws (11) and two 5/16 in. star washers (5). Torque to 17 ft-lbs (23 Nm). Road King Classic Custom models . Mount Kit Number 52903-01 is required for installation. Install solo seat (7) by sliding front of seat into holder bracket on bike. • 1999 and later models . Using Mount Kit Number 52903-01, secure the rear mount bracket with the two mushroom nuts (10) and two 1/4 in. star washers (6). Torque to 72 in-lbs (8.13 Nm). • 1998 and earlier models . Using Mount Kit Number 52903-01, secure the rear mount bracket with the two mushroom screws (11) and two 5/16 in. star washers (5). Torque to 17 ft-lbs (23 Nm)

Incoming search terms:

Harley Davidson FL series Electra Glide, Ultra Classic, Road King, Road Glide Left and Right Mounting Plate Installation Installation Manual

0

Filed Under (Harley Davidson) by admin on 25-02-2012

download
Remove existing control arm end cap and grind the outside flush. See picture below for reference. The swing arm will drop if both sides are removed at the same time. To ease installation, complete one side before starting on the other. Note: there is a left and right. Left and right end caps shown. 2. Install mounting plate assembly 10002351 on top of the end cap using 7/16″ hex head bolt and lock washer in the bottom hole. Use the 7/16″ counter sink bolt in the top hole. Make sure the end cap is seated properly. The end cap notch should fit into the recess on the frame. The pivot arm assembly is shipped on mounting plate assembly; you may remove the pivot arm to make installation easier. 3. Snug up the bolts evenly, make sure the end caps are not crooked in relation to the frame. Tighten both bolts to 25 ft lbs. (Further tightening will be required after the toe in is set). 4. If you removed the left hand pivot arm assembly, remount it now, 10002575-A (pg 20) with seal, bearings (2), washer, nut, cotter pin and dust cover. 5. Repeat for right hand side. 5 Toe In Adjustment Adjustment made with the mounting plates, bolts, pivot arms, and hubs (without wheels and tires) in place

KTM Starter Gear Maintenance Instructions

0

Filed Under (KTM) by admin on 26-11-2010

download
Checking the electric starter motor for wear -Check Bendix 1 for smooth operation and signs of wear. -Check the sprocket of the electric starter for wear and radial clearance. -Replace O-ring 2 of the electric starter. -Replace gasket 3 . -Check starter idler gear 4 for smooth operation and wear, check that the bearing bushings are seated firmly. Electric starter motor – checking for and adjusting play -Mount the electric starter and the starter idler gear. -Mount the tighten cover 5 . -Move starter idler gear 4 back and forth in the direction of rotation, the maximum play may not exceed half the width of a tooth. -If play is larger, cover 5 must be removed and as many shims 6 with a thickness of 0.10 mm as necessary must be added to eliminate all play. Then remove one shim again. -Check the play again; the maximum play may not exceed more than half of the width of a tooth. 1 2 3 4 5 4 5 6

Incoming search terms:

2000 Harley-Davidson FLHRCI Road King Classic

0

Filed Under (Harley Davidson) by admin on 03-11-2010

download
the Road King® Classic is a motorcycle with enough traditional styling to drop jaws throughout the continent. The Road King® Classic boasts laced wheels, fat white-walls and gorgeous leather saddlebags with hard inserts so they keep their shape across the long miles. Slightly narrower new handlebars provide improved ergonomics. Fender tips, tank and seat valance all boast a metal emblem. The model is available with a fuel-injected, chrome-and-black Harley- Davidson® Twin Cam 88 engine. Specifications: Engine Type: 1449 cc, 4-Stroke, Air Cooled, V-Twin Engine Bore and Stroke: 95.3 mm x 101.6 mm Valves 2 valves/cylinder Claimed Horsepower: 67 hp (50 kW) @ 5200 rpm Maximum Torque: 110 Nm (81.1 ft. lbs) @ 3100 rpm Transmission type: 5 speed Final Drive: Belt Tire – Front: 130/90-16 Tire – Rear: 130/90-16 Brakes – Front: dual 292 mm discs with 4-piston calipers Brakes – Rear: single 292 mm disc with 4-piston calipers

Harley-Davidson Road King Classic Tour Pack INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-10-2010

download
1. Close the bag completely. Support the outside of the bag with a covered piece of soft material to prevent marring or scratching. 2. Position the template on the outside of the bag, centered between the buckles. Align the template along the gap between the seams as shown at right. Tape the template in place. 3. Drill all of the small holes on the template using a 1/4″ drill bit for the assembly holes. Drill or punch the 3/4″ hole for the lock. 4. Sandwich the lock. item 4, between items 3 and 5 as shown above in FIG.1. Fasten it to the bag with the black slotted blind screws (items 7). Sandwich the leather between the lock cover plate (item 6) on the outside and the lock assembly. It may be necessary to remove a section of excess overlapped leather. 5. Use the phillips head screws (item 7) provided to attach the spring loaded ratched bar assembly. 6. Lock operation. *a. rotate the locking bar down as the bag is closed * * so that it is started into the lock aseembly. *b. check that the bag straps are outside of the bag. *c. Press the bag lid down as your help to align the * * bag lock assembly with the locking ratched bar. the ratchet bar whill operate smoothly into the * * lock when properly aligned.

Harley Davidson Road King Lightbar installation manual

0

Filed Under (Harley Davidson) by admin on 06-03-2012

download
This product is designed to mount in the lowest, visible section of the motorcycle windshield. 1. Install the 3 housing edge seals (1 long seal and 2 short seals) onto the lightbar as shown (Fig. 1). Make sure that the seal is oriented so that the lip curls inward (Fig 2). 2. Remove the 3 screws shown from the upper section of the windscreen (Fig. 3.). CAUTION! DO NOT LOOK DIRECTLY AT THESE LED’SWHILE THEY ARE ON. MOMENTARY BLINDNESS AND/OR EYE DAMAGE COULD RESULT! IMPORTANT WARNING! WARNING! All customer supplied W ires that connect to the positive terminal of the battery must be sized to supply at least 125% of the maximum operating current and FUSED at the battery to carry that load. DO NOT USE CIRCUIT BREAKERS WITH THIS PRODUCT! Fig. 1 Fig. 4 Fig. 3 Fig. 2 3. Position the lightbar into its mounting position behind the windscreen. When properly positioned, the holes in the lightbar mounting tabs will be aligned with the vacant holes through the windscreen. 4. Using the mounting hardware included with the lightbar, secure the lightbar to the windscreen assembly. 5. Route the wires to their respective destinations (Fig. 4). It is left to the installation technician’s discretion to select a path for these wires that will both protect them from possible damage and not interfere with the operation of any other vehicle components or equipment

Harley-Davidson Road King Classic Saddlebag Locks INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 24-10-2010

download
1. Cut off the back stud (at the pointed end of the emblem) with a hacksaw. Hacksaw must have a fine tooth metal cutting blade. Allow blade to slide along the flat edges of the emblem as shown. 3. Place washer (J) over emblem stud and insert threaded stud through the hole in the backing plate (L). Place cloverleaf spring (K) over the stud and onto the backing plate with the dome facing up. Place flat washer (J) and nylon cap nut (I) on the stud and tighten until a smooth open/close rotation is achieved. See illustration at right. Emblem should snap in place and not rattle* 2. Thread the front stud with the tap provided. OIL THE STUD FIRST. Thread the stud square, using a socket or wrench. Make no more than a half turn at one time, always backing up one-half turn each time. 4. Pin template on the bag with #10 screws (T) provided. Make two 5/16″ holes where shown. Make one 3/4″ hole where shown with a punch, hole saw or drill bit. If drilling the 3/4″ hole always cut the leather off first using a sharp knife. Punches, either knock-out type or gasket type do the best job without removing the leather layer

Harley-Davidson Road King Handlebar Removal and Installation Manual

0

Filed Under (Harley Davidson) by admin on 18-03-2012

download
If the wire length appears to be too short, you will have to lengthen the wires. If that’s the case, I must stress that soldering your wires is far superior to using butt splices. Wiring can be pulled from the splices and the splices themselves will take up a lot of room, making your harness bulky. To extend your wires, ensure the wire segments you are going to splice into the harness are of the same gauge as the original harness. Also, it’s a good idea to cut all of the wire segments now, ahead of time, to the same measured length. This will ensure that once all of the new wire Figure 4. Handlebar harness plug wires as they appear from the back of the plug (where the wires enter the plug from the harness) segments are spliced in, all of the finished wires are of the same length and the pins are lined up. Work from wire to wire, cutting them by staggering the cuts about an inch or so apart (see figure 5). This will prevent a bulge in your harness where all the soldering connections are. After cutting each wire, slide on a two-inch piece of heat shrink tubing before starting your soldering. Remove about ¾” of insulation from the ends of the two wire ends (one wire end being the harness, the other being the segment of new wire being spliced in). Halfway down the length of its exposed section, bend each wire 90 degrees and hook the two wire segments together at the bends. Holding the wires securely with a pair of pliers, twist them in opposite directions around each other. Make sure the ends of the wires are wrapped as tight as possible so their sharp points will not cut through the heat shrink tubing when it’s applied. Apply some soldering flux (a little is all you need) and solder the connection by first applying your soldering iron (or gun) to the wire and then applying the solder to the wire. You should not apply the solder directly to the iron as overheating the solder can lead to poorly made solder joints and improper conduction of electricity. When the connection has cooled, slide your heat shrink tubing over the joint and heat it so that the tubing shrinks, making a nice tight seal.

2010 Harley-Davidson FLHR Road King front and rear 4-piston braking system Installation

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
in Vivid Black with blue and silver pinstripes, six-speed. Air-cooled, Twin Cam 96™ engine with Electronic Sequential Port Fuel Injection (ESPFI), ABS, security system, cast wheels with independent front and rear 4-piston braking system. Motorcycle generously donated by Harley-Davidson Motor Company Police & Fleet Sales. MSRP excludes all taxes title/documentary fees, registration, tags, dealer prep, labor and installation charges, insurance, optional equipment and accessories, certificate of compliance or non-compliance fees, and finance charges. Delivery must be coordinated through Rockville Harley-Davidson by November 30, 2010. Winner is responsible for any applicable fees above. 6,000 tickets printed. Odds of winning are 1:6,000. Ticket holder need not be present to win. Licensed by the D.C. Lottery and Charitable Games Control Board. Must be 18 years or older to win. No substitutes, return for cash, or other models. As per IRS tax code, amounts paid for chances in a raffle do not qualify as a deductible charitable contribution. Taxes on prizes are the responsibility of the winner. Harley-Davidson is proud to be a sponsor of the National Law Enforcement Officers Memorial Fund. Harley-Davidson Motor Company is a prize provider only, and Harley-Davidson, Inc., and Harley-Davidson Motor Company have no responsibility regarding conduct or administration of the raffle.

Incoming search terms:

HAR:EY DAVIDSON FLHR/C/S (Road King) FRONT END LOWERING KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2011

download
Removal (Left and Right Forks) 1. Place suitable blocking under frame to raise front wheel several inches off the floor. For best results, use a hydraulic center stand on a level surface. 2. Refer to Touring Model Service Manual and remove front wheel, fender and brakes. 3. Refer to Touring Model Service Manual and remove headlamp nacelle. 4. Loosen fork cap bolt from fork tube plug at top of fork tube, but do not remove. 5. See Figure 1. Standing at front of vehicle, loosen pinch bolt (with lockwasher) on right side of lower fork bracket, but do not remove. 6. Spray glass cleaner on fork tube above the rubber fork stop. After lubricating surfaces, move fork stop up fork tube until it contacts bottom of upper fork bracket. 7. Holding fork slider to prevent fork from dropping, remove fork cap bolt from fork tube plug. Slide fork tube down and out of upper fork bracket, fork stop, lower fork bracket and slider cover. 1 WARNING 1 WARNING 1 WARNING 1 of 5 ® Kit Number 54614-05 Figure 1. Loosen Pinch Bolt on Lower Fork Bracket i04808 1 Fork cap bolt 2 Fork stop 3 Pinch bolt 8. Thread fork cap bolt back into fork tube plug to prevent loss of oil while handling. 9. Move forks to bench area. Place suitable drain pan on floor beneath vise. 10. Repeat Steps 2-6 to remove left fork. Left And Right Fork-Disassembly 1. Remove nuts, lockwashers, flat washers and axle holder from studs at end of fork slider. 2. See Figure 2. Obtain FORK TUBE HOLDER (Part Number HD-41177) and proceed as follows: a. Clamp end of tool in vise in a horizontal position with plastic knobs facing toward you. b. See Figure 3. With the fork cap bolt topside, clamp fork tube between rubber pads on inboard side of tool. Tighten knobs until fork tube is securely held. 3. Remove fork cap bolt from fork tube plug. Remove quad ring seal. Save bolt but discard quad ring seal. 4. Using wrench flat, slowly unthread fork tube plug from fork tube. Be aware that fork tube plug is under spring pressure, so have a firm grasp on plug as the last thread is turned. 5. Remove fork spring from fork tube. 6. Remove fork assembly from fork tube holder. 7. Turning fork upside down, drain fork oil into drain pan. For best results, slowly pump fork tube and slider at least 10 times. 8. Install fork spring back into fork tube. 9. Place a shop rag on the floor, and turning fork assembly upside down, press end of spring against rag. While compressing spring to prevent rotation of damper tube, remove 6mm screw from end of fork slider. Use air impact wrench for best results. 10. Remove and discard fork spring. 11. Remove and discard damper tube. 12. Remove wear ring and rebound spring. Discard rebound spring. Do not expand or stretch retaining clip to remove from fork tube or clip may become bent or distorted. 13. Using pick tool, remove retaining clip between fork slider and fork tube. 14. Remove fork tube from fork slider. NOTE To overcome any resistance, use the fork tube as a slide hammer, that is, first push fork tube into fork slider and then pull it outward with a moderate amount of force. Repeat this sequence until fork tube separates from fork slider. 15. Slide fork oil seal, slider spacer and slider bushing off end of fork tube. Discard fork oil seal and slider bushing. 16. Remove the lower stop. Right and Left Fork-Assembly Exercise caution to avoid scratching or nicking fork tube. Damaging tube can result in fork oil leaks after assembly. 1. See Service Parts Illustration. Obtain new Damper Tube (Item 7, Part Number 46532-04) from kit. Obtain new Rebound Spring (Item 8, Part Number 46273-02) from kit and install on opposite end. Install wear ring removed in step 12. 2. With the wear ring topside, slide new damper tube into fork tube, so that tube end drops through hole at bottom of fork tube. Install lower stop at end of damper tube. 3. Install fork slider in fork tube holder. Slide fork tube into fork slider. 4. If necessary, obtain new slider bushing (14) (Part Number 45940-84, not included). Coat slider bushing ID with clean fork oil. Slide slider bushing down fork tube. 5. Slide slider spacer down fork tube until it contacts slider bushing.

Incoming search terms:

Incoming search terms: