1998 honda valkyrie plate air guide

You search Auto repair manual PDF 1998 honda valkyrie plate air guide, if there are search results will appear below. If search results do not exist, please search by others keyword.



  1998 honda valkyrie plate air guide Direct Download speed 5282 Kb/s

  1998 honda valkyrie plate air guide Full Version speed 6162 Kb/s



MOUNTAIN BIKE AIR SHOCK SET-UP AND TUNING GUIDE

0

Filed Under (Tips and Review) by admin on 01-12-2010

download
DETAILED SET-UP 2. Installing Air Pressure – Remove the air cap from the Schrader valve on the end of the shock body. Attach the pump to the Schrader valve. Some people damage their pumps by screwing them on too far. As soon as the gauge registers pressure, screw 1/2 turn more and pump to the desired level. Use the release button on the pump to reduce air pressure. The hiss you hear when unscrewing the pump is only the air from the pump and not from the shock! Likewise, when you install the pump again, you will also hear a hiss as air from the shock fills the pump and reduces the registered pressure you previously installed. All perfectly normal when pressurizing the shock! After removing the pump, be sure to reinstall the Schrader valve cap. If the shock does not dampen properly after pressurizing, the air pressure may have been lost during pump removal as a result of a worn pump fitting o-ring that needs replacement. Do not ride the bike until the shock is properly pressurized. 3. Main Air Spring Pressure Adjustments – Air Spring adjustments are made by inflating or deflating the main air spring chamber. Since your IFP air pressure adjustment (outlined above) also affects your starting spring force, you should always adjust your IFP pressure before adjusting the main air spring pressure. You can refer to the online Quick Start guide at: www.progressivesuspension.com/literature.html for accurate main air spring pressure and sag settings matched to your bike model and body

Victory Freedom Engines Installation Instructions for S&S Air Cleaner Kit

0

Filed Under (Victory) by admin on 31-10-2010

download
1-Locate and remove the Intake Air Temperature Sensor (IATS) from the stock Polaris Victory air box. Locate the new position for the IATS on the bottom of the S&S air cleaner. Push the IATS in the lower air cleaner cover and turn1⁄ 4 turnin either direction, make sure you feel it lock into place. Inspect from the inside of the air cleaner to ensure that the barbs are locked into place. See Picture 1. 2-Using the stock Polaris Victory air box gasket (PN 5811908) and S&S supplied (Qty 4) M6 fasteners, assemble the lower air cleaner cover to the throttle body using 243 Blue Loctite®on the treads. Torque the M6 fasteners to 72-96 inch pounds. 3-Position the S&S pre-formed air filter onto the lower air cleaner cover ensuring that it fits into the machined groove. 4-Install the top air cleaner cover on top of the filter ensuring that it fits into the machined groove. 5-Make surethat the filter is situated in the machined grooves on both the top and bottom air cleaner covers. 6-Using 243 Blue Loctite on the threads of the S&S supplied (Qty 3) M6 fasteners tighten down top air cleaner cover evenly until seated. Finish torque the fasteners to 72-96 inch pounds. Now you’re ready for breather hose and barometric pressure hose routing. 7-Locate the S&S supplied 3⁄ 16 “reinforced hose and clamps. Push one end of the hose on the 3⁄ 16 “brass barb in the bottom air cleaner cover and slide clamp up around the end of the hose. The other end of the hose is for the Barometric Pressure Sensor (MAP). Route the hose towardthe back of the engine over the top of the rear rocker cover. 8-Remove the MAP sensor from the stock Polaris Victory air box. Remove the orange rubber gasket from the MAP sensor. Slide the S&S supplied clamp over the 3⁄ 16 “rubber hose that leads to the air cleaner. Push the barbed end of the MAP sensor into the 3⁄ 16 ” rubber hose and slide clamp up to the end of the hose around the barb. A small amount of lubricant may be applied to the barb on the MAP sensor to make installation easier. 2 S&S Air Cleaner Assembly 41-0021 (Calibration cardnot shown) Picture 1 CAUTION WARNING WARNING Plastic barb locked in recess.
9-Assemble and install breather hose as follows: A-Cut the stock Victory®hose on the straight section just behind the 90 degree bend as shown in Picture 2 . B-Slide an S&S supplied 1⁄ 2 “hose clamp over the modified stock breather hose. C-Install the S&S straight barb in Victory breather hose and position a hose clamp around hose end. D-Slide the 90-degree end of breather hose over the brass barb on the air cleaner cover and slide hose clamp in place. E-Position straight end of the S&S breather hose over the 1⁄ 2 “barb to connect to the Victory hose. Slide clamp over connection. F- See Pictures 3 and 4 for breather hose and barometric pressuresensor hose installation positions. NOTE: S&S breather hose can be cut for best fit

Incoming search terms:

HARLEY DAVIDSON TOURING LAYBACK LICENSE PLATE MOUNTING KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 28-02-2011

download
This kit fits all 1999 and later FLHR (Road King®) models, FLTR (Road Glide®) and FLHT (Electra Glide® standard) models having license plates measuring a maximum of 7-1/4 x 4-1/4 inches (184 x 108 mm). Also fits 2003 FLHRSEI2 (Screamin’ Eagle® Road King). Does not fit with Detachable Tour-Pak Rack, part number 53276-04. Does not fit 2002 FLHRSEI (Screamin’ Eagle Road King). Kit Contents See Figure 1. INSTALLATION 1. Remove the license plate from the vehicle (if installed). Remove the two hex head bolts holding the original equipment (O.E.) license-plate bracket in place. The bolts and license-plate bracket can be discarded. 2. See Figure 1. Install the new layback license plate holder (1) using the button-head hex socket screws (3) from the kit. Tighten the screws to 19 ft-lbs (25.8 Nm) . 4 1 3 7 5 2 6 is02737 1. License plate holder, layback 2. Foam pad (6) 3. Screw, button head, hex socket (2) 4. License plate frame 5. Set screw, socket head (2) 6. Hex key 7. Reflector assembly, Part Number 59365-07 Figure 1. Layback License Plate Mount Components 3. Position the license plate onto the foam pads (2) of the license plate holder, centering and aligning the plate parallel to the holder edges for best appearance. NOTE Slots in the inside top edge of the license plate frame (4) fit over the two tabs on the top edge of the license plate holder. 4. Hook the top of the license plate frame over the top edge of the holder. Swing the bottom edge of the frame inward, holding the license plate in position against the pads. 5. Use the hex key (6) from the kit to securely fasten the license plate frame to the holder with the two socket head set screws (5)

HONDA GL1500CD/ VALKYRIE Specifications

0

Filed Under (Honda) by admin on 29-01-2011

download
position when it comes to the environment. We continue to develop low-emission technologies for our current and future motorcycles, ATVs, scooters and personal watercraft. We already produce models that exceed the stringent 2008 CARB emissions requirements years ahead of schedule. And that’s the kind of performance everybody can appreciate. BE A RESPONSIBLE RIDER. Riding a motorcycle is an exercise in responsibility—to yourself, to others, to the environment and to the sport. So remember, wear a helmet, eye protection and protective clothing whenever you ride. Never ride under the influence of drugs or alcohol, and never use the street as a racetrack. Inspect your motorcycle before riding, read your owner’s manual, and see your local Honda Dealer concerning reimbursement through the Honda Rider’s Club of America™for Motorcycle Safety Foundation (MSF) rider training.* Always obey local laws, use common sense, and respect the rights of others when you ride. Make sure you have a proper license when riding on public roads, and never modify your motorcycle’s exhaust system. 03 SPECIFICATIONS ACCESSORIES VALKYRIE Log on to our website at honda.com for more information about Honda Genuine Accessories . On a bike like the Valkyrie, you can never have too much chrome. And that’s precisely why we offer our Chrome Sidecovers and Chrome Swingarm-Pivot cover to help really brighten up these areas. Here’s one of our most popular Valkyrie accessory options. These Leather Saddlebags look great, hold plenty, and match some of the other leather accessories we have available. Got a long trip planned, or is winter right around the corner? Then make sure you take a look at-or should we say take a look through-a Honda Genuine Accessories Windshield for your new Valkyrie. GL1500CD 1520cc liquid-cooled horizontally opposed six-cylinder with belt-driven overhead camshafts Six 28mm constant-velocity carburetors 71.0 x 64.0mm Solid-state digital Five-speed constant-mesh Shaft 150/80R-17 radial 180/70R-16 radial Dual-disc with twin-piston calipers 28.9 inches 66.5 inches 5.3 gallons, including 1.1 gallon reserve 681 pounds Black Windshield, leather saddlebags, chrome exhaust tips, chrome rear carrier, CB transceiver kit, passenger CB talk switch, studded backrest pad, studded main seat, studded rear seat, deluxe backrest pad

Incoming search terms:

Honda Valkyrie Air Horns Installation Instructions

0

Filed Under (Honda) by admin on 29-12-2010

download
Horns: Remove the stock horn by unplugging the wires and removing the 12mm acorn nut. This will leave an 8mm stud exposed. Notice in the hardware kit there are two brackets supplied. Locate the “L” bracket with a tab welded to it. Place the end with an angle cut close to the hole over the stud and secure with the acorn nut see photo(1) . Bolt the horn set to this bracket using the 5/16 ” x ¾” bolt and lock washer. ( NOTE: When installing with “Baker” air wings use the additional bracket, bolt & nut supplied to move the horns forward to clear the air wings) . Hose and wires: Plug the long hose into “Y” fitting on the horn set, plug the gray cord into original horn wires, and wrap the connections with electrical tape. Route both under fuel tank then back to right side cover go behind the ignition switch and between the frame rails. (A piece of stiff wire pushed from the back of the fuel tank to the front will make this much easier, Tape the wires and hose to this wire and pull back through. ) Wiring: See photo (2) Install white wire on compressor (­) terminal. Install red wire onto the compressor (+) terminal. Push hose onto compressor air fitting. Attach compressor to frame tube as shown with hose barb and mounting bolt tab straddling the frame using the two long cable ties provided. NOTE: Be sure air hose is not pinched or kinked. Attach gray cable wire terminal ends to relay terminals #85 and #86. (see wiring diagram) It doesn’t matter which wire goes to which terminal. Attach red wire to one of the remaining relay terminals. Attach the fuse wire to the remaining terminal of the relay. Remove the 1″ x 3″ black plastic cover from the main fuse holder (see photo 2A) . Attach the opposite end of the fuse to the upper­most screw. Re­install the cover. Attach white ground wire to side cover mount ing stud as shown in photo #2B

2009 Kawasaki ULTRA 250X/ 260X FUEL INJECTION CONTROLLERS And REGULATORS INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
The R&D high performance Air Filter Kit will improve acceleration and top speed performance by increasing air flow and reducing air temperatures that enter directly into the Ultra 250X’s air plenum box area. The O.E.M. air plenum box on the Ultra 250X is a great design that will flow plenty of air. However, the air that feeds the plenum box is heated by the engine. R&D has created an easy to install “flat filter” that installs directly in place of the large center access inspection cover located directly under the main glove box. The R&D Flat Air Filter insert will allow unrestricted fresh and cool air to enter the air plenum box area which will add power you can feel and a nice high performance tone. The R&D Performance Filter Kit also features two filters, one for each of the surge and blowoff protections valves. The O.E.M. surge valve recycles compressed hot air back into the air box plenum at idle and under deceleration conditions. The R&D surge and blowoff valve filter kit removes the air recycling hoses which will keep the hot air from entering the air plenum box reducing the engines intake air temperatures. The R&D Ultra 250X Air Filter Kit offers great performance tips on how to remove the restrictive air vent hoses which will further reduce the under seat ambient air temperatures. The R&D Filter system does not remove or alter the O.E.M. plenum box in any way, therefore there are no questions to be answered regarding water ingestion

Incoming search terms:

Air Shock Installation Instructions

0

Filed Under (Tips and Review) by admin on 24-11-2010

download
Air HoseInstallation. Choose the most convenient loca- tiononyour motorcycle for the air fill valve. Drilla 5/16″hole and install the air fill valve as shown in Figure 3orsecure air fill valve to frame tube. 2. Keep hose ends clean during installation because dirt can cause air leaks. 3. Install hose connector, tube clamp and two O-rings onto one end of the air hose (See Figures4&5) Apply rubber lubricant (soap solution, not oil) to the O-rings to ease installation on the air hose& into the shock absorber inlet. Plastic connector should just bottom on fitting. Do not overtighten! The function of the nut is to hold everything together in place, the O- rings do the sealing. Fin- gertightenonly (10 in/lb maximum). 4. After routing the air hose, trim the length to fit air fill valve. Install hose connector, tube clamp, and twoO-rings onto end of hose (See figures 4&5). Lubricate as above and assemble to air fill valve. Use the same procedure formating hose. Important —leaveasmall amount of slack in hose near shock absorber to allow for the slight move- mentofthe shock. Caution! Do not install hose near ex- haustsystem, battery or any other sharp edges or seat movement. Keep hoses clear of moving parts such as wheels or suspension components. Do not allow hoses to have excess slack and sag below the motorcycle. The hoses could catch on road surfaces or debris and could be damaged while the motorcycle is in motion. 5. If necessary the air hose can be secured along the motorcycle’swiringharness with tie-wraps. 6. Testing: Inflate system to 50 psi. Apply soapy water solution to all connections and check for air leaks. If there are any leaks, disconnect the suspected fitting and check for dirt or damage to the air line or the O-rings. Remove any dirt or foreign matter, re-lubricate the O-rings and reinstall. If unable to locate the leak, remove rubber boot from shocks and submerge pressurized components under water (in- cludingT-Valve) and check for leaks. If you cannot solve the air leak problem, please contact our technical staff for assistance

Honda VT1100 Shadow Guide Plug Patch Repair Manual

0

Filed Under (Honda) by admin on 24-04-2011

download
Find the guide plug.bn The guide plug is shown in the shop manual with the engine removed from the frame and the left crankcase cover removed. (You’ll find this illustration in the “ELECTRIC STARTER/STARTER CLUTCH” chapter in the “STARTER DRIVEN GEAR/STARTER CLUTCH REMOVAL” section.) It’s a little bit harder to find it on the bike. Start by following the yardstick to see where the guide plug is on my bike. To find it on your bike, lie on the ground (or, preferably a mechanics creeper) next to the bike (without the yardstick) and peek under the shift lever and over the frame There it is, just barely visible from the side of the bike. Here’s what a new one looks like: 2. Clean the guide plug and crankcase. From the front of the bike, clean the guide plug and crankcase with brake cleaner in a VERY focused spray. Let the cleaner evaporate before moving to the next step. Page 4 Rev: Draft 5/20/2007 Page 4 of 5 3. Reposition the guide plug. a. From the side of the bike, use the yardstick (or a long screwdriver if you prefer) to gently push the guide plug back into the crankcase. (Note the JB Weld from the previous patch operation.) b. From the front of the bike, gently push upward on the bottom of the upper tab (as shown below) or the bottom of the forward tab to rotate the guide plug into the proper position while maintaining pressure with the yardstick

HONDA CBX 750F (RC17) OWNERS MANUAL

0

Filed Under (Honda) by admin on 26-11-2010

download
Front air pressure adjustment: 1. Place the motorcycle on its centre stand. Do not use the side stand, or you will get false pressure readings. 2. Remove the front fork air valve cap (1). Check the air pressure. NOTE: Some pressure will be lost when removing the gauge from the valve. Determine the amount of loss and compensate accordingly. 3. Add air to the recommended pressure. NOTE: We recommend that you do not exceed the recommended air pressure or the ride will be harsh and uncomfortable. 4. Reinstall the front fork air valve cap. Rear air pressure adjustment: 1. Place the motorcycle on its centre stand. 2. Do not use the side stand, or you will get false pressure readings. 3. Remove the right side cover. 4. Remove the valve air cap (2). Check the air pressure with an air pressure gauge. NOTE: Some pressure will be lost when removing the gauge from the valve. Determine the amount of loss and compensate accordingly. 5. If required, add air up to the recommended pressure. 6. Reinstall the air valve cap (2) and the right side cover

Suzuki C50/ M50 Boulevard BIG AIR KIT INSTALLATION

0

Filed Under (Suzuki) by admin on 13-03-2012

download
1. Remove the (2) Bolts at the top of the stock air cleaner to the left and right of the oval rubber hose coming from under the fuel tank. 2. Loosen the hose clamp at the base of the oval rubber hose on the top of the air cleaner. 3. A male barb protrudes from the rear of the air cleaner that inserts into a rubber grommet mounted to the cylinders. Pull the air cleaner away from the cylinders firmly and you will feel the barb release. Now pull the upper section of the air cleaner downward to remove it from the oval snorkel tube from under the fuel tank. 4. Now you can reach to the rear of the box and unplug the electrical lead for the Air Sensor” which sits just about in the middle of the rear of the air cleaner. Now remove the breather hose at bottom of the air cleaner. 5. Set the air cleaner aside and turn it over to access the back. Remove the single bolt that secures the Air Sensor” (This sensor will be installed into the Aluminum Manifold of your new BAK assembly later) 6. Remove the lower mounting arm assembly from the cylinders. (You will not reuse this). 7. Using the (2) Dome head m6 x 15mm screws install the (2) #1 Arms to the rear (the side without the groove) of the backing plate, the shiny/chrome side of the arms should face outward. The smaller of the two holes in each arm is the one you place the screws through. Use the m6 Flange Nuts to secure the bolts at the rear of backing plate. Snug these up but do not tighten fully.

Incoming search terms: