Suzuki C50/ M50 Boulevard BIG AIR KIT INSTALLATION

0

Filed Under (Suzuki) by admin on 13-03-2012

download
1. Remove the (2) Bolts at the top of the stock air cleaner to the left and right of the oval rubber hose coming from under the fuel tank. 2. Loosen the hose clamp at the base of the oval rubber hose on the top of the air cleaner. 3. A male barb protrudes from the rear of the air cleaner that inserts into a rubber grommet mounted to the cylinders. Pull the air cleaner away from the cylinders firmly and you will feel the barb release. Now pull the upper section of the air cleaner downward to remove it from the oval snorkel tube from under the fuel tank. 4. Now you can reach to the rear of the box and unplug the electrical lead for the Air Sensor” which sits just about in the middle of the rear of the air cleaner. Now remove the breather hose at bottom of the air cleaner. 5. Set the air cleaner aside and turn it over to access the back. Remove the single bolt that secures the Air Sensor” (This sensor will be installed into the Aluminum Manifold of your new BAK assembly later) 6. Remove the lower mounting arm assembly from the cylinders. (You will not reuse this). 7. Using the (2) Dome head m6 x 15mm screws install the (2) #1 Arms to the rear (the side without the groove) of the backing plate, the shiny/chrome side of the arms should face outward. The smaller of the two holes in each arm is the one you place the screws through. Use the m6 Flange Nuts to secure the bolts at the rear of backing plate. Snug these up but do not tighten fully.

Incoming search terms:

2007 SUZUKI SV650 CUP RULES

0

Filed Under (Suzuki) by admin on 22-02-2012

download
suzuki SV650 Cup motorcycles must meet the requirements of Lightweight Sportbike Equipment except as noted: a) The exhaust system may be replaced with commercially available aftermarket exhaust systems meeting mandatory track noise limits. b) The rear shock may be replaced with an after-market shock. c) Front forks must remain stock. Internal springs, valving, and oil may be changed with any aftermarket components. d) All riders must race on the same brand of tires. For 2007 the spec tire will be Pirelli . The Pirelli SuperCorsa Pro 120/70-17 SC1 (Super Soft) front and the Pirelli SuperCorsa Pro 160/60-17 SC2 (Soft) rear for dry weather and the Diablo Rain 120/70-17 SCR1 (Super Soft) front, 160/60-17 SCR1 (Super Soft) rear for wet weather conditions. e) Steel braided brake lines may be used to replace stock lines. Calipers and rotors must remain stock. (After market brake pads are acceptable.) f) Horsepower limit: 75hp measured at the rear wheel (Sanctioning body to enforce if required). g) Suzuki SV Cup Machines must weigh no less than 365 pounds in the same condition in which they finish the race, including all fluids such as oil, water and fuel. Weights will be checked immediately following races, and no fluid may be added prior to the determination of weight or before the post race horsepower check on the dyno.

MPS Sport Bike Auto Shift Installation Manuals

0

Filed Under (Suzuki) by admin on 21-02-2012

download
The first thing to do is remove the seat, fuel tank, and possibly the front fairing if equipped. You will need plenty of room to work. Electrical Connections – You will need to locate and test a few things on your bike before you start wiring. A good ground, an ignition switched 12 volt power source, the horns, and the ignition coils. We have plug n play style harnesses available for some bikes. Check the web site for specific models. Control Box Wiring Coils – Most four cylinder motorcycles use either a individual firing system or a waste spark system. Waste spark is by far the most common. All four cylinder bikes with only two coils use a waste spark system. Most late model four cylinder sport bikes use waste spark systems even though they have four individual coils. Bikes with a waste spark systems will need the 360 calibrated unit. The 360 calibrated Sport Bike Autoshifts are identified by the 360 engraved into the box below the wire lead exit. The P/N for these boxes has the 360 as a suffix. (P/N 1-0299-360) Some of the newest fuel injected bikes (Hayabusa, GSXR1000, ZX12) that have cam sync sensors are individual firing. These bikes will require 720 calibration and will have no outside identifiers and the P/N 1-0299. The Sport Bike Auto Shift has four brown wire leads that are connected to the negative of each individual coil on a four coil system. You will notice that the connector for the four brown wires has a molded in ridge that marks the brown wire that is used as the rpm sensor. This must be connected to the number one cylinder coil negative wire.

SUZUKI Hayabusa, GSXR 1000, GSXR 750, GSXR 600 Sport Brake Lever INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 21-02-2012

download
Before you install your new ASV brake lever, you MUST choose the correct brake light switch tab to install. You will find in the package with this lever one plastic bag with four smaller bags inside of it. One bag has two small phillips screws. The other three bags have small black aluminum blocks (light switch tabs) with labels on them. Part# BRC511-H is ONLY for HONDA motorcycles. Part# BRC511-STK is for all SUZUKI, TRIUMPH and 05-06 KAWASAKI ZX636R motorcycles ONLY. Part# BRC511-K is for all KAWASAKI motorcycles EXCEPT the 05-06 ZX636R . Choose the correct tab for your bike and install it onto the lever as shown in photo 2b using the two small Phillips head screws provided. It is recommended that you use locktite or another type of thread locking adhesive to make sure these screws do not come loose. Be sure to tighten these screws as tight as you can without stripping them. The brake stop / light tab is required for your ASV brake lever to work properly Carefully place the lever into the master cylinder while inserting the plunger rod into the barrel hole as shown in photo 4. Install the main pivot bolt, and tighten it until it is snug against the master cylinder. Do not over-tighten, as it could cause the lever to bind in the master cylinder

Suzuki GSX-R 1000 AFR Tuner INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 20-02-2012

download
The installation of the AFR Tuner should be done by experienced technicians only. Always disconnect the battery from the motorcycle before making any modification to the wiring harness. Remove the negative terminal from the battery before starting the installation work. The quality of the installation work greatly affects the reliability of the AFR Tuner and the motorcycle. Work precisely and very carefully when modifying the wiring harness of the vehicle. Always double check that the wire you are about to cut or tap into is the correct one. The ECM or the AFR Tuner can be destroyed by a faulty installation. 3.2. Installing the AFR Tuner to the wiring harness 3.2.1. Main cable The AFR Tuner connects to the motorcycle through its Main connector . Figure 2 shows the wiring diagram and the necessary modifications, which needs to be made when installing the unit into the fuel injection system of the motorcycle. Information about the ECM terminal numbers and wire colors for some popular motorcycles can be found in Chapter 6 . The best location for installing the AFR Tuner main unit is at the passenger seat area of the motorcycle mounted in the trunk space or on the subframe under the fairing, as this place provides protection from engine heat and the weather. Electrical contact between the metal casing of the AFR Tuner and the rear subframe must be prevented by using insulating material, such as the included self adhesive velcro strips. If necessary use some cable ties to secure the unit in place. The installation of the AFR Tuner into the wiring harness involves tapping into some wires and cutting others while connecting the two ends to the AFR Tuner. The harness modifications are best done near the ECM, since most of the wires can be found there. Part of the wiring modifications are related to connecting the AFR Tuner in-line between the ECM and the fuel injectors. In such cases when the motorcycle is equipped with primary and secondary injectors the AFR Tuner has to be installed on the primary injectors, which operate under all engine conditions. Correct grounding of the AFR Tuner is very important for electrical noise reduction. The above mentioned insulation of the metal case from the motorcycle frame is necessary for the same reason, which is to avoid the forming of a ground loop. An even more important requirement is the correct connection of the three ground wires of the AFR Tuner. As shown on Figure 2 , these three wires must be led out separately to the ECM and connected together at same point where the ECM ground wire is tapped into. This point should be as close to the ECM terminal as possible. For best quality of the electrical contacts all connections should be done by soldering and covering the exposed part of the wire with heat shrink tubing. For reliability reasons do not use clip on type wire taps

Suzuki C-90 VL 1500LC Rear Lowering Kit INSTALLATION AND REMOVAL MANUAL

0

Filed Under (Suzuki) by admin on 20-02-2012

download
1. Decide how far you would like to lower your bike. Refer to the hole-index chart in these instructions to determine the proper mounting location holes for the drop you want to achieve. 2. Secure motorcycle to bike lift and raise the motorcycle so the rear wheel is unweighted. 3. For easiest access to the linkage remove the tool kit holder from the left side of the bike. 4. Loosen and remove the two self-locking nuts and flat washers from connecting arm bolts from the left side of the motorcycle. 5. Slide connecting arm bolts out (it may be necessary to push bushing back to the left side to allow bolt head to drop below frame. Reinstall in the same manner). Replace stock connecting arms with your new Baron connecting arms. The end with the single hole goes down and attaches to relay arm. The end with three holes goes up and attaches to the frame. Use the hole that lowers the rear your chosen amount. Reinstall bolts, washers and nuts. Torque the two connecting arm nuts to 35 foot-pounds (48 Nm). Remove motorcycle from lift. NOTE : We recommend that you set the shock spring preload to a higher setting, especially if the motorcycle will be used for carrying a passenger or heavy loads.

SUZUKI PKT-045 V-STROM LEFT FRONT PANEL Installation Manual

0

Filed Under (Suzuki) by admin on 19-02-2012

download
STEP #1 – Remove the seat & the left side fairings. See the Suzuki service manual. STEP #2 – Drill a 18mm hole into the panel (11/16″ hole saw recommended and is available on our site) where shown [A]. If the hole is too small for the socket open it with emery cloth or a file. Watch the clearance behind the panel; make sure the socket has room. Attach the socket to the panel; use a dab of Silicone on the socket and jam nut. Important: Do NOT use Loctite or over-tighten. STEP #3 – Install the cable starting at the battery through to the front of the bike. Route the cable under the bracket [B]. You’ll find it a bit tight to get through between the frame and motor [C]. Ty-wrap the cable to the frame. Run the cable up to the front fairing. Slip the fuse-holder in the location shown [D]. Disconnect the black and red battery terminals. Connect the ground wire to the bolt [E]. You can cut a notch in the ref boot [F]. Connect the red wire to the battery posts as follows: RED WIRE = BATTERY POSITIVE STEP #4 – Reconnect the positive & negative battery terminals. Install the fuse in the fuse-holder. The center terminal is plus and the outer ring is negative (see dwg below). Apply either dielectric grease or Vaseline to terminals. Connect the red wire to the POSITIVE terminal and the black wire to the NEGATIVE terminal. Use a voltmeter to check if the polarity is correct. STEP #5 – Apply the remaining ty-wrap to the wiring harness where needed. Do NOT allow the harness to directly contact the motor or exhaust.

SUZUKI M50 / C50 Fuel Injected Models INSTALLATION INSTRUCTIONS

0

Filed Under (Suzuki) by admin on 19-02-2012

download
1. Remove seat and left side covers. 2. Remove fuel tank. We highly recommend you consult the factory service manual for proper removal of fuel tank. Remove fuel tank rear mounting bracket 3. Route wiring harness under frame by fuel tank rear mounting bracket and up left side of the engine. (Fig. 1) 4. Unplug the TPS connector (black) and connect the two white 3-pin connectors in-line with the factory TPS connector. (Fig. 2) 5. Disconnect the factory connector from rear injector and connect to Fuelpak connector. (Fig. 3) 6. Connect other Fuelpak connector to injector. (Fig. 4) 7. Route black wire to battery negative connection as shown. (Fig. 5) 8. Attach Fuelpak to Fuelpak harness and mount next to battery with Velcro. (Fig. 6) 9. Follow the service manual to reinstall the fuel tank.

Suzuki M 109 WINDSHIELD INSTALLATION AND OWNER'S MANUAL

0

Filed Under (Suzuki) by admin on 18-02-2012

download
Position the motorcycle securely on its stand or a work stand. Cover the front fender and fuel tank with a cloth to avoid scratches from dropped tools. 1. Use the above diagram toidentify left from right Lower and Upper Mount Brackets. Figure 1 2. Cut each of the clamp spacers in half to make 8 pieces, each 2.5 x 1.55″. 3. Apply one spacer to the inside of each mount bracket. Figure 2 Figure 1 Figure 2 N28201 and N28202 WINDSHIELD INSTALLATION AND OWNER’S MANUAL for SuzukiĀ®M109 Right and Left side of Motorcycle is determined while sitting on the bike. Determine left from right Upper bracket. Washer angles inboard about 5 degrees. Note, Angle distinguishes Right from Left Lower Mount Bracket 1 2 4 3 5 6 8 9 10 National Cycle, Inc. Maywood, IL 60153-0158 USA 708-343-0400 / Fax: 708-343-0625 www.nationalcycle.com / e mail:info@nationalcycle.com Page 1 of 3 10-114056-000 08/07 / Rev B. 03/08 7 3, Left Upper Bracket 4, Right Upper Bracket About 5 0 inboard angle
INSTALLATION Measurements provided for clamp location. From this point you can adjust the brackets 1″ (22mm) higher if you prefer keeping in mind, position of the front nose of windshield should have a minimum of 1/2″ (13mm) clearance from cowling . Figure 3. Right Side Lower Mount Assembly 1. Start on the Right Side of motorcycle. At the top of the fork, place one inner black clamp on the fork tube. Figure 4 2. Hook the RIGHT SIDE lower mount bracket (2) to the inside clamp. Figure 5 3. Slide assembly down fork so bottom edge of bracket is 1.75″ (44mm) from top of lower triple clamp. Adjust bracket so flat in bracket runs parallel with motorcycle. Figure 6 and 7 4. Loosely install one M8 x 16 screw. (6mm Hex Key) Figure 7 Right Side Upper Mount Assembly 5. Place the second inside black clamp on the right fork tube.

Suzuki M- 109 Front Head Pipe Installation Manuals

0

Filed Under (Suzuki) by admin on 18-02-2012

download
1. Remove seat (Fig 1) remove right side (Fig 2) panel with allen 6mm bolt and push-pin snap. (Fig 3) Figure 1 Figure 2 Figure 3
- 3 – 2. Remove 6mm bolt on heat shield and remove heat shield. (Fig 4) Figure 4 3. Remove two 8mm bolts on top muffler and remove two 8mm stock bolts on bottom muffler and remove mufflers. (Fig.5 & 6) Figure 5 Figure 6 4. Remove frame cover with stock allen 6mm bolt. (Fig 7) Figure 7 FFF – 4 – 5. Loosen brake pedal bolts to allow more room to remove the exhaust. (Fig 8) Figure 8 6. Remove exhaust system by removing stock 8mm bolts on exhaust flanges. (Fig 9) Figure 9 7. Unplug EXCVA wire connectors. (Fig 10) Figure 10 – 5 – 8. Remove three 8mm stock mufflers mounting brackets bolts as shown. (Fig 11) Figure 11 ffff 9. Remove EXCVA unit from the stock muffler bracket. (Fig 12) Figure 12 10. Remove the stock pulley from the EXCVA actuator unit as shown. (Fig 13)

Incoming search terms: