XR 600 Dual Sport Kit Installation Manual

0

Filed Under (Pulsar) by admin on 27-10-2010

download
1. Get a degree in Mechanical and Electrical Engineering. (Just kidding!) 2. Remove the side panels, seat, and gas tank. 3. Unplug the headlight and taillight from the stock wiring and remove. 4. Locate the AC voltage regulator mounted on the left side of the frame backbone, (Fig.1) unplug from wiring harness, and remove the regulator. This regulator is located above the air box on ’87 and earlier XR 600′s and 500′s. AC Regulator (Remove) Pulsar Coil Alternator (Stator) Wiring Alternator (Stator) Contains both exciter coil and lighting coils Figure 1: If you are colorblind or even think you might be a little color blind, now is the time to get someone to assist you. Successful installation of the kit requires good color recognition. You want to go riding this weekend, don’t you? 5. A three wire group consisting of a black/red wire, a green wire, and a white/yellow wire (may appear light gray/yellow) are the output leads from the stator. 1990 and earlier models only have two wires coming up from the alternator, a black/red wire and a blue wire. On 1991 – 1999 XR 600′s, unplug the green wire and the white/yellow wire. (This should have already been done 3 when you removed the voltage regulator in Step 4.) On 1990 and earlier XR 600′s see the Stator Modification Instructions enclosed. 6. Temporarily disconnect the black/red wire and remove the rubber boot that shields the wire bundle. Reconnect the black/red wire making sure that it plugs in tightly, as this lead is responsible for powering the bike’s ignition. 7. Voltage Regulator Installation: The voltage regulator/rectifier mounts to the top right rear corner of the air box (Photo 1). Use the template provided to determine the location at which to drill the two 1/4 inch mounting holes in the air box lid. The outside edge of the regulator should be nearly flush with the outside edge of the air box when mounted properly.

Pulsar XR 650R ELECTRIC-START KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Pulsar) by admin on 27-10-2010

download
1. Remove the seat, fuel tank, side panels, muffler, and headers. 2. Disconnect the stator wires from their corresponding mates underneath the seat (trace the wires up from the left side case.) Un-route the stator wiring so it hangs free from the left side case. 3. Remove the stock shift lever and the left side engine case cover. You do not need to drain the oil from the engine. 4. Unbolt and remove the stator and wiring from the stock cover. Do not cut any wires. 5. The stock pulsar coil (small black box hanging from the stator) will have to be modified slightly to clear the ring gear before installation into the new cover. Remove (file or grind) about .030 inches of material from the base of the pulsar coil so that the base is flush with the face of the rest of the coil as shown in Photos 1 and 2. File Here Photo 2 Make flush with this surface Remove material here Photo 1 6. Install the stator and modified pulsar coil into the new engine case cover as shown in Photo 3. Use the three provided Phillips head bolts, split lock-washers, and plastic cable clamps to secure the wiring as shown. You will need to pull about ½” of extra wire through the grommet (Photo 4) to give you enough wire length for the grommet to sit in its case cutout. To do this, remove the electrical tape from the end of the stator wires and pull each wire individually through the grommet. Neither of the stock metal wire guides will be used when reinstalling the stator into the new case (Photo 5). 5/16″ cable clamps 1/8″ cable clamp Photo 3 Photo 5 Not Used Pull extra wire through grommet Photo 4 7. Remove the stock flywheel nut (An air impact tool works best to remove this nut without turning the motor). Remove the flywheel using the flywheel puller provided. 8. Locate the T and F marks on the stock flywheel (Photo 6). The T mark is used to adjust valve clearances and its location needs to be transferred to the ring gear. Scribe a line in the edge of the flywheel in line with the T mark as shown in Photo 7

Incoming search terms:

Pulsar Electronic LED Turn Signal Flasher Unit Installation & Operation Instructions

0

Filed Under (Pulsar) by admin on 27-10-2010

download
1. Locate the stock flasher unit on your motorcycle and remove it. Refer to your motorcycle’s shop manual. 2. Using either the test light or voltmeter, connect or touch one lead to the chassis or ground. Turn on the ignition switch. 3. Then touch the probe of either the test-light or the other lead of the voltmeter to one of wires or contacts where the flasher was removed from. If using the test-light, the light will light up when the supply line has been located. If using the voltmeter, the meter will indicate a voltage value, if present. Important Notice: Verify which grounding type your motorcycle is using before performing one of the following procedures. This can simply be done by seeing which terminal of the battery is connected to the motorcycle’s chassis or frame. Figure 3 • Positive Earth: Connect the black wire (-V) into the contact that indicated power was present. Plug the white wire (O/P) into the other contact, which did not have any power present. Turn off the ignition switch. Cut off the connector on the red wire w/ fuse holder (+V); strip the insulation back about ¼” (6 mm) and install the ring terminal on the wire, then ground the ring terminal to a chassis bolt or screw. If ground is not available via the chassis, then connect to an earth (ground) wire from the wiring harness. • Negative Ground: Connect red wire w/ fuse holder (+V) into the contact that indicated power was present. Plug the white wire (O/P) into the other contact, which did not have any power present. Turn off the ignition switch. Cut off the connector on the black wire (-V); strip the insulation back about ¼” (6 mm) and install the ring terminal on the wire, then ground the ring terminal to a chassis bolt or screw. If ground is not available via the chassis, then connect to a ground wire from the wiring harness