Baja SC50 SCOOTER OWNER'S MANUAL

0

Filed Under (Bajaj) by admin on 26-11-2010

download
Engine oil level a) Check for leaks b) Tighten filler cap securely. c) Add oil if required. 2. Fuel level a) Add fuel as necessary. b) Do not overfill (no fuel in the filler neck). c) Do not mix oil with gas. d) Replace cap tightly. e) Do not refuel a hot engine. Allow engine to cool before adding fuel. 3. Warning decals a) Make sure all warning decals are legible and securely attached. b) Replace as necessary. 4. Tires a) Ensure that both tires have at least 1/8 in. tread depth at center. b) Both tires must be inflated to the pressure indicated on the tire sidewalls. c) Replace the tires id tread height is less then 1/8 in. at the center of tires. 5. Drive chain a) Check condition and tension. b) Lubricate and adjust tension as necessary. 6. Throttle a) Check for smooth operation. Make sure the throttle “snaps” back to idle. b) Check for frayed cable or damaged cable housing. Replace damaged cable. c) Check for mud, debris and ice in the throttle cable/mechanism. Clean out any contamination.

Baja BA 250 ATV OWNER'S MANUAL

0

Filed Under (Bajaj) by admin on 26-11-2010

download
FUEL AND OIL FUEL Proper fuel is very important for the engine. Ensure there is no dust, dirt, or water which has mixed in the fuel. Use regular unleaded gasoline with an octane number 90 or higher. ENGINE OIL Your 250cc ATV has a four-stroke engine. Please use oil as described in the chart below. By using prescribe oil, you will realize the best lubrication for engine. Use the chart to select a viscosity rating based on the temperature range in your area. NOTE: In very cold weather (below 5°F (-15°C), use SAE10W-30 for good starting and smooth operation. SAE 10W-30 SAE 20W-40 ENGINE TEMP. °C °F -30 -22 40 104 -10 14 0 32 10 50 20 68 30 86 -20 4 FUEL AND OIL 8 LOCATION OF LABELS Read and follow all of the warnings labels on your ATV. Make sure you understand all the labels. Keep the labels on the ATV. Do not remove them for any reason. If a label comes off or becomes difficult to read, you should get a replacement by contacting BAJA INC. 1 – Red Light – Reverse indicator Light illuminates when ATV is in Reverse. 2 – Green Light – Neutral indicator Light illuminates when ATV is in Neutral. 3 – Ignition key switch – Turn right (CW) “RUN”, Turn left (CCW) “OFF”. ATV will only start when ignition key is turned to the “RUN” position. Make sure ignition key switch is in the “OFF” position when not in use

Baja DR70 Dirt Bike OWNER'S MANUAL

0

Filed Under (Bajaj) by admin on 25-11-2010

download
Before Starting the Engine/Motor 1. Engine oil level a) Check for leaks b) Tighten filler cap securely. c) Add oil if required. 2. Fuel level a) Add fuel as necessary. b) Do not overfill (no fuel in the filler neck). c) Do not mix oil with gas. d) Replace cap tightly. e) Do not refuel a hot engine. Allow engine to cool before adding fuel. 3. Warning decals a) Make sure all warning decals are legible and securely attached. b) Replace as necessary. 4. Tires a) Ensure that both tires are in safe riding condition. b) Both tires must be inflated to the pressure indicated on the tire sidewalls. 5. Drive chain a) Check condition and tension. b) Lubricate and adjust tension as necessary. 6. Throttle a) Check for smooth operation. Make sure the throttle “snaps” back to idle. b) Check for frayed cable or damaged cable housing. Replace damaged cable. c) Check for mud, debris and ice in the throttle cable/mechanism. Clean out any contamination. 5 SAFETY GEAR A DOT approved motorcycle helmet is the most important part of you safety gear. A DOT approved motorcycle helmet can help prevent a serious head injury. Choose a helmet that fits snugly. Motorcycle dealers can help in selecting a good quality helmet which fits properly.

Bajaj Removing And refitting Automatic Cam Chain Tensioner

0

Filed Under (Bajaj) by admin on 31-10-2010

download
1. Remove the 2 Flanged Bolts securing the Tensioner Assembly. 2. Remove Tensioner Assembly from the engine block. 3. Unscrew and remove Lock Bolt. 4. Remove Pushrod, Ball & Retainer, Spring and “O” ring. Clean parts thoroughly and apply grease to the Balls & Retainer. Re-assembly procedure : 1. Place Spring on Pushrod and compress the spring beyond the hole in the Pushrod. 2. Insert a pin or wire into the hole in the Pushrod to hold the Spring in its’ compressed position. 3. Place Balls & Retainer onto Pushrod. 4. Insert Pushrod into the Tensioner body with the small flat on the Pushrod facing, and aligned with, the Locking Bolt hole. 5. Insert the Locking Bolt and tighten it against the small flat on the Pushrod to lock the Pushrod in the compressed position. Remove the pin that’s holding the Spring compressed. 6. Install the Tensioner assembly onto the cylinder block and install and tighten both Flanged Bolts. Be sure that the “O” ring has been installed at the base of the flange. 7.Looosen the Lock Bolt to release the Pushrod, then re-tighten the lock bolt

2002 Chetak And 2003 Legend Evaporative Emission Control System Hookup

0

Filed Under (Bajaj) by admin on 31-10-2010

download
2002 Legend engines have the carburetor air vent hose connected between the 2 way valve and the canister, with a 108 main jet in the carburetor. The 2003 Legend engines have the air vent connected as shown in this diagram and the main jet increased to 120 to compensate for the reduced bowl pressure. All 2003, and subsequent Legend and Chetak engines, will have this hookup as shown with 120 size main jets. Warning: Seemingly small changes can make a big difference in altering the fuel/air ratio. Disconnect hoses or make changes at your peril. There is no horsepower to be gained by disconnecting this passive emission control system

Incoming search terms: